
Rubber & FoamSKU IP-WGS-22X16.25-11
EPDM Glazing Weatherstrip Seal 22mm x 16.25mm – For 4.75mm Glass & 2.6–3.25mm Panel – 11m to 30m
Price shown updates with the option you pick.
A 22mm x 16.25mm solid black EPDM glazing weatherstrip that locks glass, acrylic or polycarbonate up to 4.75mm thick into a 2.6mm to 3.25mm steel or aluminium panel. Once a filler strip is pressed into its top groove the seal grips both edges and gives an air-tight, water-tight joint that shrugs off sun, rain and frost. You get one continuous length cut to the size you choose, from 11m up to a full 30m coil.
At a glance
- Size: 22mm wide x 16.25mm high, solid EPDM rubber, black
- Glass slot: 4.75mm wide, 7mm deep: takes glazing up to 4.75mm thick
- Panel slot: 3.25mm wide, 8mm deep: fits 2.6mm to 3.25mm sheet
- Gap to leave: 7mm between the edge of the glass and the edge of the panel aperture
- Corners: bends round a 64mm minimum radius
- Temperature: -40°C to +90°C; resists UV, ozone and weathering
- Locking: needs a filler strip in the top groove (sold separately)
Technical drawing

How it fits

Typical uses
- Vision panels in machine guards, plant enclosures and control-room doors made from 3mm sheet
- Cab and body windows on agricultural, construction and utility vehicles
- Wheelhouse and cabin windows on workboats
- Kiosk, booth and portable-building glazing
- Replacing perished lock-strip glazing rubber on 3mm panels
Specification
| Property | Value | Test method / source |
|---|---|---|
| Overall width | 22.0 mm | Supplier drawing, nominal |
| Overall height | 16.25 mm | Supplier drawing, nominal |
| Glass slot width | 4.75 mm (glass up to 4.75 mm) | Supplier drawing |
| Glass slot depth | 7 mm | Supplier drawing |
| Panel slot width | 3.25 mm (panel 2.6–3.25 mm) | Supplier drawing |
| Panel slot depth | 8 mm | Supplier drawing |
| Glass-to-panel clearance | 7 mm | Supplier data |
| Minimum bend radius | 64 mm | Supplier data |
| Material | Solid EPDM (ethylene propylene diene monomer) | Supplier data |
| Colour | Black | – |
| Hardness | 65–75 IRHD | International Rubber Hardness Degrees |
| Tensile strength | 10 MPa | Supplier material data |
| Elongation at break | 500 % | Supplier material data |
| Tear strength | 50 kN/m | Supplier material data |
| Compression set | 21 % | 22 hours at 70 °C |
| Service temperature | -40 °C to +90 °C | Supplier data |
| Weight | 0.22 kg per metre | Supplier data |
| Density | about 1.1–1.4 g/cm³ | Typical for solid EPDM, not tested on this profile |
| Dimensional tolerance | about ±0.3–0.5 mm on these sizes | Typical for EPDM extrusions (ISO 3302-1 E2), not tested on this profile |
| Supplied as | One continuous length, 11 m to 29 m in 1 m steps, or a 30 m full coil | – |
Materials and compliance
This seal is extruded from solid EPDM rubber, chosen for its resistance to UV, ozone, rain and temperature swings outdoors. The manufacturer does not claim any food-contact, drinking-water, fire-rating or other formal approvals for this profile, so we do not claim them either. If your project needs a certificate, ask us before ordering.
Which size do I need?
| Seal size | Glass thickness | Panel thickness |
|---|---|---|
| 15mm x 12.5mm | Up to 3mm | 0.8mm – 1.6mm |
| 15mm x 13.5mm | 4.75mm | 1.2mm – 1.6mm |
| 22mm x 16.25mm (this seal) | Up to 4.75mm | 2.6mm – 3.25mm |
| 27mm x 25mm | Up to 6mm | 9.5mm |
The panel thickness decides the size. With 4.75mm glass in a 1.5mm panel choose 15mm x 13.5mm; in a 3mm panel choose this 22mm x 16.25mm seal.
How much do I need?
Add up the perimeters of all the openings and allow about 100mm per window for the joint. Example: four guard windows of 800mm x 600mm have a 2.8m perimeter each, so 4 x 2.9m = 11.6m. Choose the 12m length. Every length is supplied as one continuous piece, so you can run several windows from it.
Fitting
- Cut the aperture 7mm larger than the glass all round and radius the corners to at least 64mm. Tighter corners make the seal kink and leak.
- De-burr and clean the panel edge, then press the panel slot on, starting at the bottom centre and working round.
- Seat the glass in the opposite slot, easing the lip over the edge with a blunt plastic tool.
- Feed the filler strip into the top groove with a fitting tool. Soapy water helps it slide; never use oil or solvent on EPDM.
- Cut the seal slightly long and push the ends together so the joint is under light compression. Bond it with a rubber adhesive if you want it sealed permanently.
Complete your project
- Weather/glazing strip fitting tool for rubber filler strips
- Filler strip for this seal: ask us and we will match it to your order
Questions
Is the filler strip included?
No. The filler strip is a separate item. It is what clamps the glass and panel, so the seal will not hold without it.
Will it take acrylic or polycarbonate instead of glass?
Yes. Any rigid sheet up to 4.75mm thick fits the glass slot.
My panel is 2mm. Will it work?
No. The panel slot is made for 2.6mm to 3.25mm sheet. For thinner panels choose the 15mm x 13.5mm or 15mm x 12.5mm seal from the table above.
What is the tightest corner it will follow?
A 64mm radius. For square corners, mitre the seal at 45° and bond the joint with rubber adhesive.
How do I cut and join it?
Cut square with a sharp knife or fine-tooth saw. Butt the ends together at the bottom of the window under slight compression and bond them with a rubber adhesive.
What temperatures and weather can it take?
-40°C to +90°C. EPDM resists UV, ozone, rain and frost, so it is a good choice for outdoor windows on vehicles, boats and buildings.
Is it oil or fuel resistant?
EPDM is not designed for constant contact with oils, fuels or solvents. Splashes that are wiped off are fine, but for oily areas ask us about nitrile or neoprene profiles.
Do you keep it in stock?
Yes. Every length from 11m to 30m is cut from stock and dispatched from the UK.
Need help choosing a glazing seal? Contact our team, or call +44 1282 277786.
Product details
| SKU | IP-WGS-22X16.25-11 |
|---|---|
| Weight | 5.34 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM Glazing Weatherstrip Seal 22mm x 16.25mm – For 4.75mm Glass & 2.6–3.25mm Panel – 11m to 30m