
Rubber & FoamSKU IP-FKMC-1
FKM Fluoroelastomer Solid Rubber Cord – 75° Shore A – Per Metre
Price shown updates with the option you pick.
This FKM solid rubber cord is a black, 75° Shore A fluoroelastomer cord for making heat- and chemical-resistant seals, O-rings and gaskets. It is sold per metre in 26 diameters from 1mm to 14mm, so you can cut exactly the length your groove or joint needs.
At a glance
- Solid round FKM fluoroelastomer cord – no bore, black
- 75° Shore A hardness for a firm, well-shaped seal
- Rated -30°C to +200°C for hot engine, oven and process duty
- Resists fuels, oils and many corrosive chemicals
- Good weather, ozone and UV resistance for exterior seals
- 26 diameters including common O-ring cord sizes (1.78, 2.62, 3.53, 5.33mm)
- Priced per metre; minimum lengths apply on smaller diameters
Typical uses
- Splicing custom O-rings and FKM cord seals for flanges and covers
- High-temperature gaskets on ovens, dryers and process equipment
- Fuel and oil system seals in transport and plant maintenance
- Groove seals on chemical-handling covers and inspection hatches
Which one do I need?
| Cord diameter | Typical fit |
|---|---|
| 1mm to 2.62mm | Small O-ring grooves, instrument covers and fine gland seals (1.78mm and 2.62mm match common O-ring cross-sections) |
| 3mm to 5.7mm | General flange and cover grooves; 3.53mm and 5.33mm match standard O-ring sections |
| 6mm to 9.5mm | Larger hatch and door grooves, oven and dryer seals |
| 10mm to 14mm | Heavy covers, wide gaps and large-section custom seals |
As a rule, choose a cord 20–30% deeper than the groove so it is compressed when the cover closes.
Technical drawing
Specification
| Material | FKM fluoroelastomer |
| Profile | Solid round cord |
| Diameters | 1mm to 14mm (26 sizes) |
| Hardness | 75° Shore A |
| Colour | Black |
| Operating temperature | -30°C to +200°C |
| Tensile strength | 7.5 MPa |
| Elongation at break | 180% |
| Compression set | 30% (22 hours at 100°C) |
| Unit of sale | Per metre (minimum 5m for 1mm to 5.7mm, 2m for 6mm to 9.5mm, 1m for 10mm and above) |
How much do I need?
Measure the centre line of the groove and add about 10mm for a clean butt joint. Example: a round flange groove with a 300mm centre-line diameter needs 3.14 x 300 = 942mm, so order 1 metre (or the minimum length for your diameter). Enter the number of metres as the quantity.
Fitting tips
- Clean the groove and mating faces so no grit holds the seal off its seat.
- Cut the ends square with a sharp blade and butt-join with a suitable cyanoacrylate adhesive for a continuous ring.
- Lay the cord into the groove without stretching it – stretching thins the section.
- Close the cover evenly so the cord is compressed by the same amount all round.
Complete your project
- Solid Silicone Rubber Cord – 60 Shore A – lower-cost option where fuels are not present
- Translucent Silicone Solid Rubber Cord – 40° Shore A – 10m Coil – softer cord for light closing pressure
- White Silicone Sponge Cord – Closed Cell – 10m Roll – sponge cord for uneven surfaces
Questions
Can I use this FKM cord with fuels and oils?
Yes. FKM is chosen for its resistance to fuels, oils and many corrosive chemicals, and it holds its shape up to +200°C.
How do I make an O-ring from the cord?
Cut the length square, then bond the two ends with a cyanoacrylate rubber adhesive, holding them together for a few seconds.
What is the minimum order length?
5m for 1mm to 5.7mm cord, 2m for 6mm to 9.5mm and 1m for 10mm and above.
Is it suitable for outdoor seals?
Yes, FKM has good resistance to weathering, ozone and UV light.
Need help choosing the right size? Contact our team for advice.
Product details
| SKU | IP-FKMC-1 |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:FKM Fluoroelastomer Solid Rubber Cord – 75° Shore A – Per Metre