
Rubber & FoamSKU IP-IELCP-127X28X23-4.5-BLACK
Rubber Cable Protector – 127mm x 28mm, 23mm Hole – 4.5m or 9m Length
Price shown updates with the option you pick.
This rubber cable protector 127mm x 28mm is a low-profile floor cover that shields power cables, air lines and hoses up to 23mm diameter where people, trolleys and vehicles cross them. It is sold as a single length of 4.5m in black, or 9m in black or grey, with a split snap-fit base so cables push in from underneath without threading.
At a glance
- 127mm wide x 28mm high, gently sloped low-profile hump
- Single 23mm diameter cable channel
- Snap-fit split base: push cables in from below, no threading
- Tough natural rubber / SBR blend, 75° ± 5° Shore A
- UV stable for long outdoor use
- Fire tested to BS 476 Part 7 Class 3, halogen free
- Low profile suits wheelchairs and reduces trip hazards
Typical uses
- Covering power leads across warehouse and factory floors
- Protecting cables and air lines in machine shops
- Temporary cable runs on construction sites and at events
- Walkways and areas with light vehicle and trolley traffic
Which one do I need?
| Protector | Size (W x H) | Cable channel | Best for |
|---|---|---|---|
| Multi-compartment, low profile | 83mm x 14mm | several small cables | Offices, walkways, flat leads |
| Rubber, 2 channel | 108mm x 14mm | two small channels | Light foot traffic, data and power |
| This rubber cable protector | 127mm x 28mm | one 23mm round hole | Single power cable or hose, foot and light vehicle traffic |
| Multi-compartment, deeper | 120mm x 24mm | several compartments | Several cables side by side |
Technical drawing
Specification
| Profile | Low hump, single round channel, split base |
| Size | 127mm wide x 28mm high |
| Cable hole | 23mm diameter |
| Material | Natural rubber / SBR blend |
| Hardness | 75° ± 5° Shore A |
| Fire test | BS 476 Part 7 Class 3 |
| Halogens | None |
| Colour | Black (4.5m or 9m) or grey (9m) |
| Unit of sale | One length, 4.5m or 9m |
How much do I need?
Measure the full width of the route people or vehicles cross and add about 0.5m each side so the cable is covered where it turns. Example: a 3.5m wide warehouse aisle needs 3.5 + 0.5 + 0.5 = 4.5m, exactly one 4.5m length; a 7m wide yard crossing needs about 8m, so choose a 9m length and trim the spare. Lengths can be cut with a sharp knife.
Fitting tips
- Unroll the protector and let it relax at room temperature so it lies flat before fitting.
- Sweep the floor clean so grit does not wear the underside or let it creep.
- Open the split base, press the cable up into the 23mm channel and let the base close behind it.
- Keep the run straight across the traffic route and avoid sharp bends where the cable exits.
- Check the cable outer diameter is 23mm or less before ordering.
Complete your project
- Rubber Cable Protector – 108mm x 14mm, 2 Channel – Per Length
- Multi-Compartment Cable Protector – 120mm x 24mm – Per Length
- Hazard Warning Cable Protector – 83mm x 16mm – Single Length
Questions
What size cable fits the 127mm x 28mm rubber cable protector?
Any single cable, air line or hose up to 23mm outside diameter fits the round channel.
Do I need to thread the cable through?
No. The split base snaps open so you push the cable in from underneath, then it closes and holds the cable.
Can it be used outdoors?
Yes. The NR/SBR rubber is UV stable for extended outdoor use.
Is it safe for wheelchairs and pedestrians?
Yes. The low, gently sloped 28mm profile lets wheelchairs and trolleys cross and reduces trip hazards.
Which colours and lengths are available?
Black in 4.5m or 9m lengths, and grey in a 9m length.
Not sure which size you need? Contact our team and we will help you choose.
Product details
| SKU | IP-IELCP-127X28X23-4.5-BLACK |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Rubber Cable Protector – 127mm x 28mm, 23mm Hole – 4.5m or 9m Length