
Rubber & FoamSKU IP-PES-10X3-10M
Polyethylene Sponge Strip – 10mm x 3mm Self-Adhesive – 10m Roll
A slim, 10mm wide x 3mm thick strip of dark grey closed-cell, cross-linked polyethylene (XLPE) foam with a self-adhesive backing on the 10mm face. Peel the liner, press it on, and it seals small gaps of about 2.5mm against dust, draughts and water. Sold as one continuous 10m roll (£1.18 per metre inc VAT), held in stock in the UK.
At a glance
- Size: 10mm wide x 3mm thick, 10m per roll
- Fixing: pressure-sensitive adhesive on the wide (10mm) face, white peel-off liner
- Seals with only 15-20% squeeze, so it suits a closed gap of about 2.4-2.6mm
- Closed cell: under 1% water absorption over 7 days
- Working temperature: -60°C to +100°C
- Light and resilient: 33 kg/m³, recovers after repeated knocks
Technical drawing

Specifications
| Property | Value | Test method / source |
|---|---|---|
| Width | 10 mm | Nominal, supplier drawing |
| Thickness (free state) | 3 mm | Nominal, supplier drawing |
| Cross-section | Solid rectangle, 30 mm² | Calculated from 10 x 3 mm |
| Length per roll | 10 m, continuous | Supplier |
| Adhesive face | 10 mm face, with peel-off liner | Supplier drawing |
| Material | Cellular polyethylene (PE) foam | Supplier |
| Cell structure | Closed cell, cross-linked, fine uniform cells | Supplier |
| Colour | Dark grey | Supplier |
| Density (block) | 33 kg/m³ | Not stated by supplier |
| Density (range) | 28-38 kg/m³ | Not stated by supplier |
| Tensile strength | > 250 kPa (0.25 MPa) | Not stated by supplier |
| Elongation at break | > 170 % | Not stated by supplier |
| Compressive strength at 10 % deflection | 35-55 kPa | Not stated by supplier |
| Compressive strength at 25 % deflection | 55-85 kPa | Not stated by supplier |
| Compressive strength at 50 % deflection | 120-170 kPa | Not stated by supplier |
| Compression set (22 h at 23°C) | 15 % | Not stated by supplier |
| Water absorption (7 days) | < 1 % | Not stated by supplier |
| Working temperature | -60°C to +100°C | Supplier |
| Compression needed to seal | 15-20 % | Supplier |
| Suggested closed gap | 2.4-2.6 mm | Calculated from 3 mm at 15-20 % squeeze |
| Weight | 0.01 kg/m (about 0.1 kg per 10 m roll) | Supplier |
| Hardness, tear strength, dimensional tolerance | Not published for this product | Ask us if you need them |
The supplier publishes these values without naming the test standards, so we have not added any. Values are typical, not guaranteed minimums.
Materials and compliance
This strip is closed-cell, cross-linked polyethylene foam with a pressure-sensitive adhesive backing. The closed cells keep water out, and cross-linking gives it a fine, even structure that spreads pressure and resists crushing from repeated impacts.
The supplier does not state any food-contact (FDA, EC 1935/2004), drinking-water (WRAS), fire-rating, REACH or RoHS approval for this product, so we do not claim one. If you need a declaration for your application, contact us before ordering.
Typical uses
- Dust and splash seals on enclosure doors, lids, access panels and inspection hatches
- Low-profile door and window seals in vehicles, boats, caravans and trailers
- Anti-rattle and vibration isolation strips under covers, trims and panels
- Shock-absorbing cushion strips and case inserts where space is tight
- Thin gaskets for small flanges and housings
Which size do I need?
| 12.5mm x 2mm | Thinnest option, for gaps of about 1.6-1.7mm. |
| 10mm x 3mm | This product. A narrow seal for gaps of about 2.4-2.6mm on flanges 10mm or wider. |
| 10mm x 4mm | Same width, a little thicker, for gaps of about 3.2-3.4mm. |
| 10mm x 6mm | Same width, twice as thick, for gaps of about 5mm or uneven surfaces. |
How much do I need?
Each roll is 10 metres. Add up the length to be sealed and divide by 10, rounding up. Example: three enclosure doors with a 1.6m perimeter each need 4.8m, so one roll; a 26m run needs three rolls.
Fitting
- Clean the surface with isopropyl alcohol or a degreaser and let it dry; the adhesive needs a clean, dry, dust-free surface.
- Fit above about +10°C if you can; adhesive tack drops on cold surfaces.
- Peel back a short length of liner at a time and lay the strip without stretching it.
- Press firmly along the whole length to bed the adhesive in, then allow time for it to build full strength before heavy use.
- Check the closed gap is about 2.4-2.6mm so the foam is squeezed by 15-20%.
Frequently asked questions
Which side is the adhesive on?
The wide 10mm face. The strip lies flat, 3mm high, with the adhesive against your surface.
What gap will a 3mm strip seal?
A closed gap of about 2.4-2.6mm, which squeezes the foam by the 15-20% it needs to seal. If your gap is bigger, choose the 10 x 4mm or 10 x 6mm strip; if the lid will not close, choose the 12.5 x 2mm strip.
What can I use it for?
Dust, draught and splash seals on cabinets, enclosures, hatches, vehicle and caravan doors and windows, plus anti-rattle strips and thin cushioning pads.
What is polyethylene sponge, and is it waterproof?
It is a closed-cell, cross-linked polyethylene foam. Because the cells are sealed it absorbs less than 1% water over 7 days, so it will not soak up water like open-cell sponge.
What temperatures can it take?
The foam is rated for -60°C to +100°C in service. Fit it on a surface above about +10°C so the adhesive grips well.
How do I cut and join it?
Cut it with scissors or a sharp knife. At corners either bend the strip round or cut two square ends and butt them tightly together; avoid gaps at joins, as that is where leaks start.
Will it stick to rough or painted surfaces?
Yes, it sticks to most clean smooth and lightly textured surfaces, including painted metal, plastics and glass. Very rough, oily or low-energy plastics (such as PE or PP) may need a primer.
Is it in stock?
Yes, we hold it in stock in the UK. Orders placed before the cut-off are dispatched the same day.
Complete your project
- Polyethylene Sponge Strip 10mm x 4mm, 10m roll
- Polyethylene Sponge Strip 10mm x 6mm, 10m roll
- Polyethylene Sponge Strip 12.5mm x 2mm, 10m roll
Need help choosing? Call +44 1282 277786 or email sales@industrial-polymers.co.uk.
Product details
| SKU | IP-PES-10X3-10M |
|---|---|
| Weight | 0.26 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Polyethylene Sponge Strip – 10mm x 3mm Self-Adhesive – 10m Roll