
Rubber & FoamSKU IP-PES-10X4-10M
Polyethylene Sponge Strip – 10mm x 4mm, Self-Adhesive – Closed-Cell PE Foam, Dark Grey – 10m Roll
A thin, self-adhesive polyethylene sponge strip, 10mm wide x 4mm thick, for sealing small gaps of about 3.2mm to 3.4mm on enclosure lids, cabinet doors, hatches, cases and panels, and for padding and anti-rattle jobs where a soft, low strip is needed. The foam is closed-cell and cross-linked, so it does not soak up water, and it seals with only a 15–20% squeeze. The adhesive is factory-applied to the 10mm face: peel the liner, press it on, done. Dark grey, supplied as one continuous 10m strip from UK stock.
At a glance
- Size: 10mm wide x 4mm thick, flat rectangular section; adhesive on the 10mm face
- Seals at 15–20% compression, so a closed gap of roughly 3.2–3.4mm
- Closed-cell, cross-linked PE foam: under 1% water absorption over 7 days
- Very wide temperature range: −60°C to +100°C in use
- Light and soft: 10g per metre; 33 kg/m³ block density; cuts with scissors or a sharp knife
- Value: £16.38 per 10m strip inc VAT, which is about £1.64 per metre
Typical uses
- Dust, draught and splash seals on electrical, control and instrument enclosure lids
- Door and window seals on cabinets, sheds, vehicles, caravans and boats where the gap is small
- Gaskets for covers, inspection plates and equipment cases
- Vibration isolation and anti-rattle pads between panels, trims and brackets
- Shock-absorbing cushions and case inserts in packaging
Technical drawing

Nominal dimensions in mm, free state before compression. The 4mm thickness is the foam only; the adhesive and liner sit under the 10mm face.
How it seals

Stick the strip flat on the frame or flange with the 10mm face down. When the lid or door closes, the foam is squeezed by 15–20% (from 4mm to about 3.2–3.4mm) and that is enough for an air- and watertight seal. Because the cells are fine and even, the pressure spreads along the strip and the foam recovers after repeated closing and knocks.
Which size do I need?
Measure the gap between the frame and the closed lid or door (feeler gauges or a stack of card). Pick a strip about 20–25% thicker than the gap. If the gap varies along its length, go thicker.
| Strip | Width x thickness | Seals a gap of about |
|---|---|---|
| PE sponge strip 10 x 3mm | 10 x 3mm | 2.4–2.6mm |
| PE sponge strip 10 x 4mm (this item) | 10 x 4mm | 3.2–3.4mm |
| PE sponge strip 10 x 6mm | 10 x 6mm | 4.8–5.1mm |
| PE sponge strip 16 x 10mm | 16 x 10mm | 8–8.5mm |
Gap figures are worked out from each strip's thickness and the 15–20% sealing compression.
Specification
| Property | Value | Test method / source |
|---|---|---|
| Profile and dimensions | ||
| Profile | Flat rectangular foam strip, self-adhesive one face | – |
| Width (adhesive face) | 10 mm | Nominal, manufacturer data |
| Thickness (foam only) | 4 mm | Nominal, manufacturer data |
| Adhesive position | On the 10 mm (widest) face, with peel-off liner | Manufacturer data |
| Length | 10 m continuous strip | – |
| Weight | 0.01 kg/m (about 0.1 kg per 10 m strip) | Manufacturer data |
| Recommended closed gap | ≈ 3.2–3.4 mm | Derived from 4 mm and 15–20% compression |
| Dimensional tolerance | Not stated by the manufacturer for this profile | – |
| Material | ||
| Material | Cellular polyethylene (PE) | Manufacturer data |
| Cell structure | Closed cell, cross-linked, fine and uniform | Manufacturer data |
| Colour | Dark grey | – |
| Density (block) | 33 kg/m³ | Manufacturer data, method not stated |
| Density (range) | 28–38 kg/m³ | Manufacturer data, method not stated |
| Hardness | Not stated for this foam (soft, low-density) | – |
| Mechanical properties | ||
| Tensile strength | > 250 kPa (> 0.25 MPa) | Manufacturer data, method not stated |
| Elongation at break | > 170 % | Manufacturer data, method not stated |
| Compressive strength at 10% deflection | 35–55 kPa | Manufacturer data, method not stated |
| Compressive strength at 25% deflection | 55–85 kPa | Manufacturer data, method not stated |
| Compressive strength at 50% deflection | 120–170 kPa | Manufacturer data, method not stated |
| Compression set, 22 h at 23 °C | 15 % | Manufacturer data, method not stated |
| Tear strength | Not stated for this product | – |
| Compression needed to seal | 15–20 % | Manufacturer data |
| Environment | ||
| Working temperature | −60 °C to +100 °C | Manufacturer data |
| Water absorption, 7 days | < 1 % | Manufacturer data, method not stated |
Materials and compliance
The strip is closed-cell, cross-linked polyethylene foam with a pressure-sensitive adhesive backing. The manufacturer does not state any product approvals (for example food contact, fire rating, REACH or RoHS) for this strip, so we do not claim any. If you need a declaration for your application, ask us before ordering and we will check what is available.
Fitting tips
- Clean the surface with isopropyl alcohol or a degreaser and let it dry. Fit above about +10°C if you can, since the adhesive grabs better when warm.
- Peel back a short length of liner at a time and press the strip down as you go. Do not stretch it, or it will creep back and leave gaps.
- Run a thumb or roller along the full length to bed the adhesive in. The bond gets stronger over the first day.
- At corners, either bend the strip round a gentle radius or cut and butt the ends tightly together. For a sharp corner, cut a 45° mitre.
Frequently asked questions
What gap does this strip seal?
About 3.2mm to 3.4mm when closed. It only needs a 15–20% squeeze to seal. A tighter gap still works but the lid needs more force to close; a gap close to or over 4mm will not seal.
Which face is the adhesive on?
The 10mm (wide) face, so the strip lies flat and stands 4mm proud of the surface.
Can I use it outdoors or where it gets wet?
Yes. The closed cells absorb less than 1% water over 7 days and the foam works from −60°C to +100°C. For long-term outdoor exposure to strong sun, check it at intervals, as with any PE foam.
How do I cut and join it?
Scissors or a sharp knife cut it cleanly. Join lengths by butting the ends tightly together; on a seal, put the joint where the lid or door presses hardest, not at a corner.
Will it stick to painted metal, plastic or wood?
Yes, to most clean, dry, rigid surfaces, smooth or slightly rough. Very low-energy plastics (some PP and PE mouldings) and dusty or oily surfaces stick less well. Clean and test a short piece first.
Is it good for vibration and rattles?
Yes. It is soft (35–55 kPa at 10% squeeze) and recovers well (15% compression set), so it works as a thin anti-rattle pad between panels, trims and brackets.
How much do I get?
One continuous 10m strip, which is about 0.1kg. Order several strips for longer runs.
Is it in stock?
Yes. It is held in stock in the UK and ships from our warehouse.
Need help choosing a size or a material? Contact our team on +44 1282 277786 or sales@industrial-polymers.co.uk.
Product details
| SKU | IP-PES-10X4-10M |
|---|---|
| Weight | 0.22 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Polyethylene Sponge Strip – 10mm x 4mm, Self-Adhesive – Closed-Cell PE Foam, Dark Grey – 10m Roll