
Rubber & FoamSKU IP-PES-16X10-10M
Polyethylene Sponge Strip – 16mm x 10mm, Self-Adhesive – Closed-Cell PE Foam, Grey – 10m Roll
A chunky, self-adhesive polyethylene sponge strip, 16mm wide x 10mm thick, for sealing gaps of about 8mm to 8.5mm on cabinet and enclosure doors, hatches, lids, vehicle and caravan lockers, sheds and equipment cases, and for cushioning and anti-vibration pads where a soft, deep strip is needed. The foam is closed-cell and cross-linked, so it does not soak up water, and it seals with only a 15–20% squeeze. The adhesive is factory-applied to the 16mm face: peel the liner, press it on, done. Grey, supplied as one continuous 10m strip from UK stock.
At a glance
- Size: 16mm wide x 10mm thick, flat rectangular section; adhesive on the 16mm face
- Seals at 15–20% compression, so a closed gap of roughly 8.0–8.5mm
- Closed-cell, cross-linked PE foam: under 1% water absorption over 7 days
- Very wide temperature range: −60°C to +100°C in use
- Light and soft: 33 kg/m³ block density; cuts with scissors or a sharp knife
- Value: £39.21 per 10m strip inc VAT, which is about £3.92 per metre
Typical uses
- Dust, draught and splash seals on electrical, control and instrument enclosure doors with a wider gap
- Door, hatch and locker seals on cabinets, sheds, vehicles, caravans and boats
- Gaskets for covers, inspection plates and equipment cases
- Vibration isolation and anti-rattle pads between panels, trims, tanks and brackets
- Shock-absorbing cushions, edge buffers and case inserts
Technical drawing

Nominal dimensions in mm, free state before compression. The 10mm thickness is the foam only; the adhesive and liner sit under the 16mm face.
How it seals

Stick the strip flat on the frame or flange with the 16mm face down. When the door or lid closes, the foam is squeezed by 15–20% (from 10mm to about 8.0–8.5mm), which is enough for an air- and watertight seal. Because the cells are fine and even, the pressure spreads along the strip and the foam recovers after repeated closing and knocks.
Which size do I need?
Measure the gap between the frame and the closed door or lid (feeler gauges, or a stack of card). Pick a strip about 20–25% thicker than the gap. If the gap varies along its length, go thicker.
| Strip | Width x thickness | Seals a gap of about |
|---|---|---|
| PE sponge strip 10 x 6mm | 10 x 6mm | 4.8–5.1mm |
| PE sponge strip 25 x 6mm | 25 x 6mm | 4.8–5.1mm |
| PE sponge strip 16 x 10mm (this item) | 16 x 10mm | 8.0–8.5mm |
| PE sponge strip 19 x 12mm | 19 x 12mm | 9.6–10.2mm |
| PE sponge strip 25 x 12mm (wider) | 25 x 12mm | 9.6–10.2mm |
Gap figures are worked out from each strip's thickness and the 15–20% sealing compression.
Specification
| Property | Value | Test method / source |
|---|---|---|
| Profile and dimensions | ||
| Profile | Flat rectangular foam strip, self-adhesive one face | – |
| Width (adhesive face) | 16 mm | Nominal, manufacturer data |
| Thickness (foam only) | 10 mm | Nominal, manufacturer data |
| Adhesive position | On the 16 mm (widest) face, with peel-off liner | Manufacturer data |
| Length | 10 m continuous strip | – |
| Weight | 0.01 kg/m as stated by the manufacturer (about 0.1 kg per 10 m strip) | Manufacturer data |
| Recommended closed gap | ≈ 8.0–8.5 mm | Derived from 10 mm and 15–20% compression |
| Dimensional tolerance | Not stated by the manufacturer for this profile | – |
| Material | ||
| Material | Cellular polyethylene (PE) | Manufacturer data |
| Cell structure | Closed cell, cross-linked, fine and uniform | Manufacturer data |
| Colour | Grey | Manufacturer data |
| Density (block) | 33 kg/m³ | Manufacturer data, method not stated |
| Density (range) | 28–38 kg/m³ | Manufacturer data, method not stated |
| Hardness | Not stated for this foam (soft, low-density) | – |
| Mechanical properties | ||
| Tensile strength | > 250 kPa (> 0.25 MPa) | Manufacturer data, method not stated |
| Elongation at break | > 170 % | Manufacturer data, method not stated |
| Compressive strength at 10% deflection | 35–55 kPa | Manufacturer data, method not stated |
| Compressive strength at 25% deflection | 55–85 kPa | Manufacturer data, method not stated |
| Compressive strength at 50% deflection | 120–170 kPa | Manufacturer data, method not stated |
| Compression set, 22 h at 23 °C | 15 % | Manufacturer data, method not stated |
| Tear strength | Not stated for this product | – |
| Compression needed to seal | 15–20 % | Manufacturer data |
| Environment | ||
| Working temperature | −60 °C to +100 °C | Manufacturer data |
| Water absorption, 7 days | < 1 % | Manufacturer data, method not stated |
Materials and compliance
The strip is closed-cell, cross-linked polyethylene foam with a pressure-sensitive adhesive backing. The manufacturer does not state any product approvals (for example food contact, fire rating, REACH or RoHS) for this strip, so we do not claim any. If you need a declaration for your application, ask us before ordering and we will check what is available.
Fitting tips
- Clean the surface with isopropyl alcohol or a degreaser and let it dry. Fit above about +10°C if you can, since the adhesive grabs better when warm.
- Peel back a short length of liner at a time and press the strip down as you go. Do not stretch it, or it will creep back and leave gaps.
- Run a thumb or roller along the full length to bed the adhesive in. The bond gets stronger over the first day.
- At 10mm deep this strip does not bend tightly: cut and butt the ends at corners, or cut a 45° mitre for a neat square corner.
Frequently asked questions
What gap does this strip seal?
About 8.0mm to 8.5mm when closed. It only needs a 15–20% squeeze to seal. A tighter gap still works but the door needs more force to close; a gap close to or over 10mm will not seal.
Which face is the adhesive on?
The 16mm (wide) face, so the strip lies flat and stands 10mm proud of the surface.
Can I use it outdoors or where it gets wet?
Yes. The closed cells absorb less than 1% water over 7 days and the foam works from −60°C to +100°C. For long-term outdoor exposure to strong sun, check it at intervals, as with any PE foam.
How do I cut and join it?
Scissors or a sharp knife cut it cleanly. Join lengths by butting the ends tightly together; on a seal, put the joint where the door or lid presses hardest, not at a corner.
Will it stick to painted metal, plastic or wood?
Yes, to most clean, dry, rigid surfaces, smooth or slightly rough. Very low-energy plastics (some PP and PE mouldings) and dusty or oily surfaces stick less well. Clean and test a short piece first.
Is it good for vibration and cushioning?
Yes. It is soft (35–55 kPa at 10% squeeze) and recovers well (15% compression set), and the 10mm depth gives plenty of travel, so it works as an anti-rattle pad, buffer or case insert.
How much do I get?
One continuous 10m strip. Order several strips for longer runs.
Is it in stock?
Yes. It is held in stock in the UK and ships from our warehouse.
Need help choosing a size or a material? Contact our team on +44 1282 277786 or sales@industrial-polymers.co.uk.
Product details
| SKU | IP-PES-16X10-10M |
|---|---|
| Weight | 0.22 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Polyethylene Sponge Strip – 16mm x 10mm, Self-Adhesive – Closed-Cell PE Foam, Grey – 10m Roll