
Rubber & FoamSKU IP-PES-19X12-10M
Polyethylene Sponge Strip – 19mm x 12mm, Self-Adhesive – Closed-Cell PE Foam, Grey – 10m Roll
A thick, soft, self-adhesive polyethylene sponge strip, 19mm wide x 12mm thick, for sealing and cushioning larger gaps of about 10mm: equipment and enclosure doors, lids, hatches, cabinet and locker doors, vehicle, trailer and boat panels, and machine guards. It is also a good shock-absorbing bumper and anti-vibration pad. The foam is closed-cell and cross-linked, so it does not soak up water, and it seals with only a 15–20% squeeze. The adhesive is factory-applied to the 19mm face: peel the liner and press it on. Grey, supplied as one continuous 10m strip from UK stock.
At a glance
- Size: 19mm wide x 12mm thick, flat rectangular section; adhesive on the 19mm face
- Seals a closed gap of roughly 9.6–10.2mm (15–20% compression)
- Closed-cell, cross-linked PE foam with a fine, even cell structure that spreads pressure and recovers after repeated impacts
- Very wide temperature range: −60°C to +100°C in use
- Light and soft: 20g per metre; 33 kg/m³ block density; cuts with scissors or a sharp knife
- Value: £47.37 per 10m strip inc VAT, which is about £4.74 per metre
Typical uses
- Dust, air and splash seals on cabinet, enclosure, locker and hatch doors with a 10mm closing gap
- Door, lid and window seals in vehicles, trailers, horseboxes, boats, caravans and transport bodies
- Shock-absorbing bumpers and door stops on lids, hatches and machine guards
- Vibration isolators and anti-rattle pads under panels, covers and equipment
- Cushioning and lining strips for case inserts, packing and tool cases
- General cut-to-length gaskets
Technical drawing

Nominal dimensions in mm, free state before compression, drawn at true proportion (1.58 : 1). The 12mm thickness is the foam only; the adhesive and liner sit under the 19mm face.
How it seals

Stick the strip flat on the frame or flange with the 19mm face down. When the door or lid closes, the foam is squeezed by 15–20% (from 12mm to about 9.6–10.2mm), which is enough for a dust, air and splash seal. The wide 19mm face gives a large bonding area, so the strip stays put on frames that are slightly uneven.
Which size do I need?
Measure the gap between the frame and the closed door or lid (a stack of coins, a rule or a ball of putty pressed shut). Pick a strip about 20–25% thicker than the gap. If the gap varies, size for the largest gap and check the door still closes easily.
| Strip | Width x thickness | Seals a gap of about |
|---|---|---|
| PE sponge strip 10 x 6mm | 10 x 6mm | 4.8–5.1mm |
| PE sponge strip 25 x 6mm (wider face) | 25 x 6mm | 4.8–5.1mm |
| PE sponge strip 50 x 8mm (very wide) | 50 x 8mm | 6.4–6.8mm |
| PE sponge strip 16 x 10mm | 16 x 10mm | 8.0–8.5mm |
| PE sponge strip 19 x 12mm (this item) | 19 x 12mm | 9.6–10.2mm |
| PE sponge strip 25 x 12mm (wider face) | 25 x 12mm | 9.6–10.2mm |
Gap figures are worked out from each strip's thickness and the 15–20% sealing compression.
Specification
| Property | Value | Test method / source |
|---|---|---|
| Profile and dimensions | ||
| Profile | Flat rectangular foam strip, self-adhesive one face | – |
| Width (adhesive face) | 19 mm | Nominal, manufacturer data |
| Thickness (foam only) | 12 mm | Nominal, manufacturer data |
| Width-to-thickness ratio | 1.58 : 1 | Calculated from nominal sizes |
| Adhesive position | On the 19 mm (widest) face, with peel-off liner | Manufacturer data and drawing |
| Length | 10 m continuous strip | – |
| Weight | 0.02 kg/m (about 0.2 kg per 10 m strip) | Manufacturer data |
| Recommended closed gap | ≈ 9.6–10.2 mm | Derived from 12 mm and 15–20% compression |
| Dimensional tolerance | Not stated by the manufacturer for this profile | – |
| Material | ||
| Material | Cellular polyethylene (PE) | Manufacturer data |
| Cell structure | Closed cell, cross-linked, fine and uniform | Manufacturer data |
| Colour | Grey | – |
| Density (block) | 33 kg/m³ | Manufacturer data, method not stated |
| Density (range) | 28–38 kg/m³ | Manufacturer data, method not stated |
| Hardness | Not stated for this foam (soft, low-density) | – |
| Mechanical properties | ||
| Tensile strength | > 250 kPa (> 0.25 MPa) | Manufacturer data, method not stated |
| Elongation at break | > 170 % | Manufacturer data, method not stated |
| Compressive strength at 10% deflection | 35–55 kPa | Manufacturer data, method not stated |
| Compressive strength at 25% deflection | 55–85 kPa | Manufacturer data, method not stated |
| Compressive strength at 50% deflection | 120–170 kPa | Manufacturer data, method not stated |
| Compression set, 22 h at 23 °C | 15 % | Manufacturer data, method not stated |
| Tear strength | Not stated for this product | – |
| Compression needed to seal | 15–20 % | Manufacturer data |
| Environment | ||
| Working temperature | −60 °C to +100 °C | Manufacturer data |
| Water absorption | No figure given for this size; closed-cell structure resists water uptake | Manufacturer data (descriptive) |
Materials and compliance
The strip is closed-cell, cross-linked polyethylene foam with a pressure-sensitive adhesive backing. The manufacturer does not state any product approvals (for example food contact, fire rating, REACH or RoHS) for this strip, so we do not claim any. If you need a declaration for your application, ask us before ordering and we will check what is available.
Fitting tips
- Clean the surface with isopropyl alcohol or a degreaser and let it dry. Fit above about +10°C if you can, since the adhesive grabs better when warm.
- Peel back a short length of liner at a time and press the strip down as you go. Do not stretch it, or it will shrink back and open gaps at the ends.
- Press firmly along the full length to bed the adhesive in. The bond gets stronger over the first day; leave it a few hours before closing a tight door on it.
- At 12mm thick the strip will not bend round a tight corner on its 19mm face: cut and butt the ends, or cut a 45° mitre for a neat square corner.
Frequently asked questions
What gap does this strip seal?
About 9.6mm to 10.2mm when closed. It only needs a 15–20% squeeze to seal. For a gap of about 8mm choose the 16 x 10mm strip; for 5mm, the 10 x 6mm.
Which face is the adhesive on?
The 19mm (wide) face, so the strip lies flat and stands 12mm proud of the surface.
Can I use it outdoors, in the wet or in the cold?
Yes. The closed cells resist water uptake and the foam works from −60°C to +100°C. For long-term outdoor exposure to strong sun, check it at intervals, as with any PE foam.
How do I cut and join it?
Scissors or a sharp knife cut it cleanly; a long blade gives the squarest cut at 12mm thick. Join lengths by butting the ends tightly together; on a seal, put the joint along a straight run where the door presses hardest, not at a corner.
Will it stick to painted metal, plastic, glass or wood?
Yes, to most clean, dry, rigid surfaces, smooth or slightly rough. Very low-energy plastics (some PP and PE mouldings) and dusty or oily surfaces stick less well. Clean and test a short piece first.
Will it stop knocks and vibration?
Yes. It is soft (35–55 kPa at 10% squeeze), so it gives easily on contact, and it recovers well (15% compression set after 22 hours), so it keeps cushioning after repeated knocks. That suits door bumpers, lid stops and anti-vibration pads.
How much do I get?
One continuous 10m strip, about 0.2kg. A 1000 x 600mm cabinet door has a 3.2m perimeter, so one strip seals three such doors.
Is it in stock?
Yes. It is held in stock in the UK and ships from our warehouse.
Need help choosing a size or a material? Contact our team on +44 1282 277786 or sales@industrial-polymers.co.uk.
Product details
| SKU | IP-PES-19X12-10M |
|---|---|
| Weight | 0.44 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Polyethylene Sponge Strip – 19mm x 12mm, Self-Adhesive – Closed-Cell PE Foam, Grey – 10m Roll