Rubber & FoamSKU IP-SILP-15X10-BLACK
Silicone L Profile – 15mm x 10mm, 60 Shore A – 25m Coil
Silicone L profile 15mm x 10mm is a heavy-wall right-angle angle trim with a 15mm base leg, a 10mm upright and solid 5-6mm walls, made to protect and seal exposed edges and corners. It is sold per 25m coil in seven colours.
At a glance
- Unequal L section: 15mm base leg with a 6mm wall and 10mm upright leg with a 5mm wall
- Thick, solid walls make it a hard-wearing rubber edge protector and corner buffer
- 60 Shore A silicone that stays flexible from -50°C to +180°C
- Material stated as FDA compliant and WRAS approved
- Resists UV, ozone and weathering for indoor or outdoor use
- Seven colours, supplied as one continuous 25m coil
Typical uses
- Corner guard on machine frames, guard panels and enclosure doors
- Silicone corner seal for hatches, cabinets and HVAC panels
- Food and drink processing equipment needing colour-coded trims
- Buffer strip on steps, ledges and sheet edges that take knocks
Which one do I need?
| Profile | Best suited to |
|---|---|
| 15mm x 11.5mm, 2mm wall | A lighter, thinner trim where flexibility matters more than impact protection |
| 14mm x 10mm | Similar footprint with a slightly narrower base |
| 15mm x 10mm (this profile) | Heavy 5-6mm walls on a 15mm base for corners that take regular knocks |
| 15mm x 12mm, 5mm thick | Same heavy wall with a taller 12mm upright to cover a deeper edge |
| 16mm x 10mm | A slightly wider base for more bonding area |
Technical drawing
Specification
| Profile | L section (angle), unequal legs |
| Base leg | 15mm wide, 6mm wall |
| Upright leg | 10mm high, 5mm wall |
| Material | Silicone rubber |
| Hardness | 60 Shore A |
| Tensile strength | 11 N/mm² |
| Elongation at break | 550% |
| Tear strength | 26 N/mm |
| Operating temperature | -50°C to +180°C |
| Compliance | FDA compliant material, WRAS approved |
| Colours | Black, blue, green, red, translucent, white, yellow |
| Unit of sale | 25m coil |
How much do I need?
Add up the length of every edge you want to cover and allow about 5% for trimming and mitred corners. For example, guarding the two vertical front corners and top edge of four 1.8m x 0.9m cabinets needs 4 x (1.8 + 1.8 + 0.9) = 18m, plus 5% = 18.9m, so a single 25m coil covers the job.
Fitting tips
- Clean the surface with isopropyl alcohol so it is dry and free of oil before fitting.
- Because the walls are thick, cut with a long, sharp blade in one stroke for a square end.
- Mitre the corners at 45° and butt the ends tightly for a neat, continuous trim.
- Bond with a silicone adhesive sealant along both legs for a permanent or watertight fix.
Complete your project
- Silicone L Profile – 15mm x 12mm – 25m Coil
- Silicone L Profile – 14mm x 10mm – 25m Coil
- Silicone L Profile – 16mm x 10mm – 25m Coil
Questions
Is this angle trim stiff or flexible?
At 60 Shore A it is flexible enough to follow gentle curves by hand, while the 5-6mm walls give it a firm, cushioned feel on corners.
Will this silicone corner seal take heat?
Yes. It is rated from -50°C to +180°C, so it suits oven surrounds, hot-air ducts and cold stores alike.
Can it be used in food production areas?
The silicone is stated as FDA compliant, and the colour options support colour-coded hygiene zones.
How is it fixed?
It is an L section, so it does not clip on. Bond it with a silicone adhesive sealant, following the adhesive maker's surface preparation advice.
Need help choosing a size or colour? Contact our technical team and we will be glad to advise.
Product details
| SKU | IP-SILP-15X10-BLACK |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone L Profile – 15mm x 10mm, 60 Shore A – 25m Coil