
Rubber & FoamSKU IP-IPEDP-11X9.5-9
EPDM D Section Door Seal – 11mm x 9.5mm for 2mm Panels – 9m to 30m Coil
Price shown updates with the option you pick.
This EPDM D section door seal, 11mm x 9.5mm, pushes straight onto a 2mm panel or flange edge. Its hollow D bulb stands about 5.7mm proud of the panel face and squashes against the door frame or mating panel as it closes, keeping out rain, draughts and dust and cushioning light knocks. It is made from solid black EPDM rubber (65–75 IRHD) and is sold as one continuous length from 9m to 29m, or as a full 30m coil.
At a glance
- Profile: 11mm wide x 9.5mm high "e" section, a hollow D bulb above a 2mm channel and a 9.5mm x 1.8mm lower lip
- Fits 2mm panel, sheet or flange edges; no adhesive needed on a clean, tight edge
- Solid EPDM, 65–75 IRHD: 10 MPa tensile, 500% elongation, 21% compression set (22h at 70°C)
- Ozone tested with no cracks; excellent weathering and UV resistance for outdoor use
- One unbroken length from 9m to 29m, or a full 30m coil at a lower price per metre
- Held in UK stock for fast dispatch; cuts cleanly with a sharp knife and is 100% recyclable
Technical drawing

Specifications
| Property | Value | Test method / basis |
|---|---|---|
| Profile type | Hollow D bulb with a side channel and flat lower lip ("e" section), push-on | Manufacturer's profile drawing |
| Overall width (across the D bulb) | 11.0 mm | Nominal, manufacturer's drawing |
| Overall height (lip to top of bulb) | 9.5 mm | Nominal, manufacturer's drawing |
| Lower lip length | 9.5 mm | Nominal, manufacturer's drawing |
| Lower lip thickness | 1.8 mm | Nominal, manufacturer's drawing |
| Channel width / panel it fits | 2 mm (fits a 2 mm thick panel or flange edge) | Manufacturer's "to fit panel" figure |
| Channel depth | About 8 mm | Scaled from the manufacturer's drawing; not separately stated |
| Bulb height above the panel face | About 5.7 mm | Worked out from 9.5 mm overall, 1.8 mm lip and 2 mm channel |
| Hollow inside the bulb | About 8 mm wide × 3 mm high | Scaled from the manufacturer's drawing; not separately stated |
| Wall thickness | About 1.2 to 1.5 mm | Scaled from the manufacturer's drawing; not separately stated |
| Material | EPDM rubber (solid, not sponge) | Manufacturer datasheet |
| Colour | Black | - |
| Hardness | 65 to 75 IRHD, ±5° (about the same as Shore A) | IRHD; manufacturer datasheet |
| Tensile strength | 10.0 MPa | Manufacturer datasheet; standard not stated |
| Elongation at break | 500% | Manufacturer datasheet; standard not stated |
| Tear strength | 50 kN/m | Manufacturer datasheet; standard not stated |
| Compression set | 21% | 22 h at 70 °C; manufacturer datasheet |
| Ozone resistance | No cracks | 72 h at 40 °C, 25 pphm ozone; manufacturer datasheet |
| Heat ageing: change in tensile strength | +9% | 70 h at 70 °C; manufacturer datasheet |
| Heat ageing: change in elongation at break | 0% | 70 h at 70 °C; manufacturer datasheet |
| Weathering and UV | Excellent | Manufacturer rating |
| Heat and cold, flex fatigue, abrasion | Good | Manufacturer rating |
| Service temperature range | Not stated for this profile. Typical for EPDM: about -40 °C to +100 °C (typical for EPDM, not tested on this profile) | Tested point stated: aged at +70 °C with little change |
| Density | Not stated for this profile. Typical for solid EPDM: about 1.1 to 1.3 g/cm³ (typical for EPDM, not tested on this profile) | - |
| Dimensional tolerance | Not stated by the manufacturer. Dense rubber extrusions are usually made to BS ISO 3302-1 class E2 (typical, not stated for this profile) | Ask us if you need a stated tolerance |
| Supplied length | Any whole length from 9 m to 29 m as one continuous piece, or a full 30 m coil | - |
| Price per metre | £23.31/m inc VAT for 9–29 m; £16.54/m inc VAT as a full 30 m coil (£496.17) | - |
| Recyclable | Yes, 100% recyclable (manufacturer statement) | - |
Materials and compliance
Solid black EPDM rubber. The manufacturer rates it excellent for weathering and UV, good for heat, cold, repeated flexing and abrasion, and its ozone test (72 hours at 40°C, 25 pphm) showed no cracking. That makes it suitable inside and outdoors on vehicles, caravans, boats and cabinets. Like all EPDM it is not suited to contact with oils, fuels or petrol-based solvents.
The manufacturer does not state any food-contact (FDA, EC 1935/2004), drinking-water (WRAS), REACH, RoHS or fire-rating approval for this profile, so we do not claim any. If your job needs a certified material, ask us before you order.
Typical uses
- Door, window and hatch edges on classic cars, caravans and motorhomes
- Bus, coach and rail vehicle panels and service doors
- Marine lockers, deck hatches and cabin doors
- Aviation ground equipment panels and access doors
- Steel electrical cabinets, enclosures and machine guards with 2mm sheet doors
Which one do I need?
| Your job | Best choice |
|---|---|
| 2mm panel edge, hollow D bulb sealing against a frame | This EPDM D section 11mm x 9.5mm |
| Bigger gap to close, same push-on D style | EPDM D section door seal 18mm x 13.75mm or 12.5mm x 9.5mm |
| 1mm to 2mm panel edge, bulb on top of a self-grip clip | EPDM self-grip door seal 15.5mm x 10mm |
| No panel edge to grip, stick-on seal needed | TPE sponge D profile 10mm x 8mm, adhesive backed |
How much do I need?
Measure every edge the seal will run along and add about 5% for trimming at the corners. Example: a steel cabinet door 1.8m high x 0.9m wide needs 2 x 1.8m + 2 x 0.9m = 5.4m, plus 5% = 5.7m, so the 9m minimum covers it with spare. Three identical doors need about 17m. Cut lengths cost £23.31 per metre inc VAT; the full 30m coil works out at £16.54 per metre, so from 22m upwards the coil is the cheaper buy.
Fitting tips
- Clean the 2mm edge and file off any burrs so the panel slides fully into the channel.
- Decide which face the bulb must seal against, then start at the least visible corner and push the channel on by hand, working along the edge.
- Lay the seal on relaxed; do not stretch it, or it can shrink back and leave gaps at the ends.
- At corners, either ease the seal round a generous radius or cut a neat mitre; butt the two ends tightly together.
- Cut with a sharp knife in one stroke so the hollow bulb is not crushed.
- Set the closed gap a little under 5.7mm so the bulb is lightly squeezed all round.
Questions
What panel thickness does this D section seal fit?
The channel is 2mm wide and about 8mm deep, made for 2mm sheet, panels and flanges. On thinner sheet it will be loose and may need a few dots of adhesive; for 1mm to 2mm edges a self-grip door seal is a better choice.
How big is it in real life?
The whole profile is 11mm wide and 9.5mm tall, about the width of a fingertip. Once fitted, the bulb stands about 5.7mm proud of the panel face, so it suits closed gaps of roughly 3mm to 5mm.
Can this EPDM door seal be used outdoors?
Yes. EPDM has excellent weathering, UV and ozone resistance, so it suits exterior doors, vehicles, caravans and marine hatches as well as indoor cabinets.
What temperature can it take?
The manufacturer does not give a range for this profile. It was heat aged for 70 hours at 70°C with almost no change, and EPDM typically works from about -40°C to +100°C (typical for EPDM, not tested on this profile).
Is the bulb solid or hollow, and is it sponge?
The bulb is hollow so it compresses easily, but the rubber itself is solid EPDM (65–75 IRHD), not sponge. That makes it tougher and more resistant to wear and knocks than a sponge seal.
How do I cut and join it?
Cut with a sharp knife or rubber cutter in one stroke. Join the ends with a tight butt joint; for a permanent, watertight joint use a cyanoacrylate (superglue) made for rubber on the cut faces.
Do I need glue to fit it?
Normally no. The channel grips a clean 2mm edge on its own. On a very smooth or slightly thin edge, a few dots of a rubber-compatible contact adhesive inside the channel stop it creeping.
Can I buy less than 9m, or more than 30m?
9m is the shortest length. Each order line is one continuous piece up to a full 30m coil; for longer runs, order more than one coil or contact us for a quote.
Need help choosing a seal? Contact our team on +44 1282 277786 or sales@industrial-polymers.co.uk and we will help you pick the right profile.
Product details
| SKU | IP-IPEDP-11X9.5-9 |
|---|---|
| Weight | 1.61 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM D Section Door Seal – 11mm x 9.5mm for 2mm Panels – 9m to 30m Coil