Rubber & FoamSKU IP-SIRU-4.1X9-25-BLACK
Silicone Round U Channel – 4.1mm x 9mm for 1.5mm Edges – 25m Coil
A silicone U channel 4.1mm across and 9mm tall, made for edges about 1.5mm thick: 16-gauge sheet steel and stainless, aluminium sheet, thin glass, acrylic, polycarbonate and laminate. The slot is 7.5mm deep, the deepest in our slim silicone range, so it covers a lot of the edge and grips on by friction alone on most 1.5mm panels. The 1.3mm walls and fully rounded base give a soft, durable bumper along the exposed face. The compound is approved for food contact and drinking water (see Material compliance). Supplied as one continuous 25m coil in seven colours, all held in stock.
At a glance
- Fits edges about 1.5mm thick (roughly 1.3 to 1.8mm)
- 4.1mm wide x 9mm high, 1.5mm slot, 7.5mm slot depth, 1.3mm walls, 1.5mm solid rounded base
- Silicone rubber, 60 Shore A: flexible, and follows curves and corners
- Continuous service from -50°C to +180°C
- FDA 21 CFR 177.2600, EC 1935/2004 and WRAS approved compound
- Unaffected by UV, ozone and weather, so it will not crack or harden outdoors
- Black, blue, green, red, translucent, white or yellow, all at the same price
- 25m coil, about £27.00 per metre inc VAT
Technical drawing
![]()
Typical uses
- Capping the edges of 1.5mm stainless guards, hoppers, chutes and covers on food and packaging lines
- Lining cut-outs and gland-plate edges in 1.5mm enclosures so cable insulation cannot chafe
- Cushioning glass or polycarbonate in cabinet doors, inspection windows and display cases
- Edge trim on tank lids, access hatches and covers in contact with drinking water
- Edge protection on oven, heater, dryer and lighting panels where rubber or PVC trims would degrade
- Colour-coding guards, trays and fixtures by line, zone or allergen
Which size do I need?
Measure the edge thickness and choose the slot that matches it most closely.
| Silicone U channel | Slot / edge thickness |
|---|---|
| Silicone Round U Channel 3mm x 5mm | 1mm |
| Silicone Round U Channel 3.2mm x 7.8mm | 1.2mm, 5mm deep |
| Silicone Round U Channel 4.1mm x 9mm (this one) | 1.5mm, 7.5mm deep |
| Silicone U Channel 7.1mm x 13mm | 4mm |
| Silicone U Channel 15mm x 20mm | 10mm |
Specification
| Property | Value | Test method |
|---|---|---|
| Profile and dimensions | ||
| Profile | Round-bottom U channel (push-on edge trim) | – |
| Overall width | 4.1 mm | – |
| Overall height | 9.0 mm | – |
| Slot (grip) width | 1.5 mm | – |
| Slot depth | 7.5 mm | – |
| Wall thickness | 1.3 mm each side | – |
| Base | 1.5 mm solid, full-round bottom (R2.05) | – |
| Fits panel / edge | 1.5 mm nominal | – |
| Dimensional tolerance | Class E2 | ISO 3302-1:2014 |
| Weight (calculated) | approx. 27 g per metre, approx. 0.7 kg per 25 m coil | From cross-section and density |
| Material properties (typical) | ||
| Material | Silicone rubber (VMQ) | – |
| Hardness | 60 Shore A | DIN ISO 48-4 |
| Density | 1.15 g/cm³ | DIN EN ISO 1183-1 A |
| Tensile strength | 11 N/mm² (11 MPa) | ISO 37 Type 1 |
| Elongation at break | 550 % | ISO 37 Type 1 |
| Tear strength | 26 N/mm (26 kN/m) | ASTM D624 B |
| Compression set | 31 % after 22 h at 175 °C | DIN ISO 815-1 Type B, Method A |
| Rebound resilience | 59 % | ISO 4662 |
| Operating temperature | -50 °C to +180 °C continuous | – |
| Environmental resistance | Ozone, UV, oxidation, weathering, cosmic and ionising radiation, corona discharge | – |
| Supply | ||
| Colours | Black, blue, green, red, translucent, white, yellow | – |
| Unit of sale | One continuous 25 m coil | – |
Material compliance
The manufacturer's datasheet for this exact profile states that its silicone compound meets:
- FDA 21 CFR 177.2600: the US regulation for rubber articles in repeated contact with food
- EC 1935/2004: the EU and UK framework regulation for food-contact materials
- WRAS approved: approved for contact with drinking (potable) water in the UK
- Free from TSE/BSE by-products: no animal-derived ingredients of TSE/BSE concern
- Phthalate-free: contains no phthalate plasticisers
These approvals apply to the material. Whether a finished assembly complies depends on its design and use. Compliance documents are available on request: contact our team.
How much do I need?
Add up every edge you want to cover and allow about 5% for trimming and joints. Example: ten stainless guard panels, each 800 x 400mm with trim on the top and both sides (1.6m each), need 16m, or about 16.8m with allowance. One 25m coil covers the job with spare.
Fitting tips
- Deburr the edge and wipe off oil and dust before fitting
- Start at one end and press the channel on with your thumb, working along the edge; the deep slot needs a firm push to seat fully
- Cut slightly over length with a sharp knife and push the ends together for a tight butt joint
- On edges under 1.3mm, or where it must be sealed or permanent, run a bead of silicone or polyurethane sealant into the slot first
Questions
What edge thickness will it fit?
The slot is 1.5mm. Silicone stretches a little, so edges from about 1.3mm to 1.8mm usually hold well. On thinner edges add a little silicone sealant so it cannot slide off; for 1.2mm edges the 3.2mm x 7.8mm channel is the closer fit.
How is it different from the 3.2mm x 7.8mm channel?
This profile has a wider 1.5mm slot that is 7.5mm deep instead of 5mm, and thicker 1.3mm walls. It suits heavier 1.5mm sheet and covers more of the edge face on each side.
Is it suitable for food equipment?
Yes. The compound is stated to meet FDA 21 CFR 177.2600 and EC 1935/2004, so it suits guards, covers and panels on food processing, packaging and catering equipment.
Can it be used with drinking water?
Yes. The material is WRAS approved for contact with potable water.
Is it suitable for hot equipment or outdoor use?
Yes. It is rated for continuous use from -50°C to +180°C and resists UV, ozone and weathering.
How do I cut and join it?
Cut it square with a sharp craft knife or scissors. For a neat joint, butt the two ends together; for a sealed joint, bond them with a silicone adhesive.
Will it go round corners?
Yes. At 60 Shore A and 4.1mm wide it bends easily round curves. On a sharp 90° corner, cut a small V notch in the base or butt two lengths together.
How accurate are the dimensions?
It is extruded to ISO 3302-1 tolerance class E2, the standard precision class for rubber extrusions, so allow a few tenths of a millimetre either way on the nominal sizes.
Is it in stock?
Yes. All seven colours are held in stock, so orders go out quickly, as shown by the dispatch message above.
Can I order a shorter length or a bulk quantity?
This listing is a full 25m coil. For cut lengths or multiple coils, ask our team for a quote.
Are all colours the same price?
Yes. Every colour is the same profile, the same compound and the same price.
Need help choosing an edge trim or seal? Call +44 1282 277786, email sales@industrial-polymers.co.uk or contact our team.
Product details
| SKU | IP-SIRU-4.1X9-25-BLACK |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone Round U Channel – 4.1mm x 9mm for 1.5mm Edges – 25m Coil