Rubber & FoamSKU IP-SITS-4X8.5-SQ-25M-BLK
Silicone T Seal Profile – 4mm x 8.5mm – 25m Coil
A solid silicone T seal with a 2.2mm leg and a 4mm-wide head, made for narrow slots at least 5.5mm deep. The leg pushes into the slot and grips its walls, and the head sits on the surface to close the gap against dust, splash, draughts and heat. You can choose a square head or a chamfered head, in any of seven colours. Every option is the same price, and each coil is one unbroken 25m length.
At a glance
- Head 4.0mm wide × 3.0mm deep; leg 2.2mm wide; 8.5mm overall height (5.5mm leg below the head)
- Two head shapes: square, or chamfered with a 3.0mm flat top and an angled edge on one side
- 0.9mm shoulder each side of the leg, so the head covers the slot edges
- Solid silicone rubber, 60 Shore A, working range -50°C to +180°C
- The manufacturer states the compound meets FDA 21 CFR 177.2600 and EC 1935/2004 for food contact. It is a WRAS approved material.
- Black, white, translucent, red, green, blue or yellow, all at the same price
- Held in stock in every colour and both head shapes
Square or chamfered head: which do I need?
| Square head | Chamfered head | |
|---|---|---|
| Head shape | Full 4.0 × 3.0mm block with square corners | 3.0mm flat top, then an angled edge down to the 4.0mm full width on one side |
| Sealing face | Flat 4.0mm face | Flat 3.0mm face plus a sloping edge |
| Best for | Doors, lids and panels that close straight down onto the seal | Panels that slide or swing across the seal, where the angled edge acts as a lead-in. Also suits frames with a bevelled or rounded corner. |
| Fitting | Either way round | Fit the angled edge facing the direction the panel comes from |
| Leg, slot size, material, price | Identical: 2.2mm leg, 8.5mm overall, 60 Shore A silicone, £675.00 per 25m coil | |
Replacing an old seal? Look at its cut end. If the top is square, order Square. If one top corner is cut away at an angle, order Chamfered.
Typical uses
- Slot seals in aluminium profile frames for machine guards and enclosures
- Access doors on air handling units, fan coil housings and ductwork
- Inspection hatches on food, bakery and packaging machinery
- Lids and doors on warming cabinets, provers and drying ovens up to +180°C
- Colour-coded seals for hygiene zones (red, green, blue, yellow)
Technical drawing
![]()
Full specification
| Property | Value | Test method |
|---|---|---|
| Dimensions | ||
| Profile type | Solid T section; square or chamfered head | – |
| Overall height | 8.5 mm | – |
| Head width (overall) | 4.0 mm | – |
| Head depth | 3.0 mm | – |
| Flat top width, chamfered head | 3.0 mm (chamfer on one side only) | – |
| Leg width (base thickness) | 2.2 mm | – |
| Leg length below head | 5.5 mm (reference) | – |
| Shoulder each side | 0.9 mm | – |
| Suits slot | Approx. 2.0–2.2 mm wide, at least 5.5 mm deep | – |
| Dimensional tolerance | Class E2 | ISO 3302-1:2014 |
| Length per coil | 25 m, one continuous length | – |
| Material and physical properties | ||
| Compound | Solid silicone rubber | – |
| Hardness | 60 Shore A | DIN ISO 48-4 |
| Density | 1.15 g/cm³ | DIN EN ISO 1183-1, method A |
| Tensile strength | 11 N/mm² (11 MPa) | ISO 37, type 1 |
| Elongation at break | 550 % | ISO 37, type 1 |
| Tear strength | 26 N/mm (26 kN/m) | ASTM D624, die B |
| Compression set | 31 % after 22 h at 175 °C | DIN ISO 815-1, type B, method A |
| Rebound resilience | 59 % | ISO 4662 |
| Service conditions | ||
| Working temperature | -50 °C to +180 °C | – |
| Environmental resistance | Ozone, UV, oxidation, weathering, corona discharge, cosmic and ionising radiation | – |
| Supply | ||
| Head shapes | Square, chamfered | – |
| Colours | Black, white, translucent, red, green, blue, yellow | – |
| Approx. weight | About 28 g per metre for the square head, slightly less for the chamfered head (calculated from section and density) | – |
| Unit of sale | 1 coil of 25 m (£27.00 per metre inc VAT) | – |
Materials and compliance
These are the claims the manufacturer makes in writing for this exact profile and compound. Ask us if your file needs the certificate or declaration.
| Claim | What it means for you |
|---|---|
| FDA 21 CFR 177.2600 | The compound meets the US rule for rubber articles in repeated contact with food. |
| EC 1935/2004 | The compound meets the EU framework regulation for materials that come into contact with food. |
| WRAS approved material | The material is accepted for contact with drinking water in UK water fittings. |
| Free from TSE/BSE by-products | No animal-derived ingredients that carry TSE/BSE risk. |
| Phthalate free | Made without phthalate plasticisers. |
The approvals cover the material as supplied. Whether your finished assembly complies also depends on its design, its cleaning regime and the other materials in it, so check it against your own requirements.
Will it fit my slot?
Measure the slot's width and depth. The leg is 2.2mm wide, so it grips best in a slot of about 2.0–2.2mm. The slot must be at least 5.5mm deep so the head can sit down flat; a deeper slot is fine. If your slot is 1.8–2.0mm wide, the 3.8mm × 7.7mm T seal with a 2.0mm leg is a closer fit. If it is shallower than 5.5mm, choose one of our shorter-leg T seals.
How much do I need?
Add up the length of every slot and allow about 5% for trimming and joints. For example, a 600mm × 400mm guard door needs 2.0m, or about 2.1m with the allowance, so one 25m coil seals 11 doors of that size.
Fitting tips
- Clear any old seal, grease and grit out of the slot, and let it dry
- Start partway along a straight side, not at a corner
- Press the leg in with your thumb or a small plastic roller as you go
- Chamfered head: keep the angled edge on the same side all the way round
- Lay the seal into corners rather than pulling it round them. Stretched silicone shrinks back and opens a gap.
- Cut the end slightly long with a sharp knife and push the ends together; a dab of silicone adhesive keeps the joint closed
FAQ: frequently asked questions
What slot does it fit?
A slot about 2.0–2.2mm wide and at least 5.5mm deep. The head is 4.0mm wide, so it overlaps the slot by 0.9mm each side and covers the edges.
What is the difference between the square and chamfered head?
Only the head. The square head is a full 4 × 3mm block. The chamfered head has a 3mm flat top with one corner angled away. The leg, height, material and price are the same.
Which way up does it go?
The 2.2mm leg goes into the slot, and the wider head sits on the surface, facing the door, lid or panel it seals against.
Can it be used near ovens and heaters?
It is rated to +180°C continuous. That suits oven and warming-cabinet doors, drying equipment and heater housings, as long as the seal itself stays at or below that temperature.
Is it safe near food or drinking water?
The manufacturer states the compound meets FDA 21 CFR 177.2600 and EC 1935/2004 for food contact, and it is a WRAS approved material. We can send the declaration if your audit needs it.
How accurate are the dimensions?
The profile is extruded to ISO 3302-1 class E2, the normal tolerance class for extruded rubber sections. Check your slot against the drawing before you order.
Will it flatten over time?
Silicone recovers well. This compound has a compression set of 31% after 22 hours at 175°C and a rebound resilience of 59%, so it keeps its seal through repeated heat cycles.
How do I cut and join it?
Cut it with a sharp knife or shears. To join it, use a silicone adhesive or silicone sealant; most general-purpose glues and contact adhesives will not bond to silicone rubber.
Is every option the same price?
Yes. Both head shapes in all seven colours cost £675.00 per 25m coil inc VAT (£27.00 per metre).
Complete your project
- Silicone T Seal Profile – 3.8mm x 7.7mm (2.0mm leg)
- Silicone T Seal Profile – 3.6mm x 8.6mm
- Silicone T Seal Profile – 4mm x 6.5mm (shorter leg)
Not sure it will fit? Send us a photo, or the width and depth of the slot, and we will check it for you. Contact our team.
Product details
| SKU | IP-SITS-4X8.5-SQ-25M-BLK |
|---|---|
| Weight | 1.54 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone T Seal Profile – 4mm x 8.5mm – 25m Coil