Rubber & FoamSKU IP-SITS-3.8X7.7-25M-BLK
Silicone T Seal Profile – 3.8mm x 7.7mm – 25m Coil
A solid silicone T seal with a deep 2mm leg, made for narrow slots that are at least 5mm deep. The leg pushes into the slot and grips its walls; the 3.8mm-wide head sits on the surface and closes the gap against dust, splash, draughts and heat. Each coil is one unbroken 25m length, available in seven colours at the same price.
At a glance
- Head 3.8mm wide × 2.6mm deep, with a flat face for even contact
- Leg 2.0mm wide × 5.1mm long; 7.7mm overall height
- 0.9mm shoulder each side of the leg, so the head covers small chips or burrs at the slot edge
- Solid silicone rubber, 60 Shore A, working range -50°C to +180°C
- Compound stated to meet FDA 21 CFR 177.2600 and EC 1935/2004 for food contact; WRAS approved material
- Black, white, translucent, red, green, blue or yellow: same size, same price
- Held in stock in every colour
Why choose the 3.8 × 7.7mm profile?
Most small T seals have a short leg of around 3mm. This one has a 5.1mm leg, so it sits deeper in the slot and is much harder to pull out when a door or lid drags across it. The firmer 60 Shore A compound helps here too: the head keeps its shape under a closing panel instead of rolling over. Choose it for slots about 2mm wide and 5mm or more deep, such as those in aluminium framing, fabricated steel door frames and machine hatches.
Typical uses
- Slot seals in aluminium profile frames for machine guards and enclosures
- Access doors on air handling units, fan coil housings and ductwork
- Inspection hatches on food, bakery and packaging machinery
- Lids and doors on warming cabinets, provers and drying ovens up to +180°C
- Colour-coded seals for hygiene zones (red, green, blue, yellow)
Technical drawing
![]()
Full specification
| Property | Value | Test method |
|---|---|---|
| Dimensions | ||
| Profile type | Solid T section, flat-faced head | – |
| Overall height | 7.7 mm | – |
| Head width | 3.8 mm | – |
| Head depth | 2.6 mm | – |
| Leg width | 2.0 mm | – |
| Leg length below head | 5.1 mm (reference) | – |
| Shoulder each side | 0.9 mm | – |
| Dimensional tolerance | Class E2 | ISO 3302-1:2014 |
| Length per coil | 25 m, one continuous length | – |
| Material and physical properties | ||
| Compound | Solid silicone rubber | – |
| Hardness | 60 Shore A | DIN ISO 48-4 |
| Density | 1.15 g/cm³ | DIN EN ISO 1183-1, method A |
| Tensile strength | 11 N/mm² (11 MPa) | ISO 37, type 1 |
| Elongation at break | 550 % | ISO 37, type 1 |
| Tear strength | 26 N/mm (26 kN/m) | ASTM D624, die B |
| Compression set | 31 % after 22 h at 175 °C | DIN ISO 815-1, type B, method A |
| Rebound resilience | 59 % | ISO 4662 |
| Service conditions | ||
| Working temperature | -50 °C to +180 °C | – |
| Environmental resistance | Ozone, UV, oxidation, weathering, corona discharge, cosmic and ionising radiation | – |
| Supply | ||
| Colours | Black, white, translucent, red, green, blue, yellow | – |
| Approx. weight | 23 g per metre (calculated from section and density) | – |
| Unit of sale | 1 coil of 25 m (£27.00 per metre inc VAT) | – |
Materials and compliance
These are the claims the manufacturer makes in writing for this exact profile and compound. Ask us for the certificate or declaration your file needs.
| Claim | What it means for you |
|---|---|
| FDA 21 CFR 177.2600 | The compound meets the US rule for rubber articles in repeated contact with food. |
| EC 1935/2004 | The compound meets the EU framework regulation for materials that come into contact with food. |
| WRAS approved material | The material is accepted for contact with drinking water in UK water fittings. |
| Free from TSE/BSE by-products | No animal-derived ingredients that carry TSE/BSE risk. |
| Phthalate free | Made without phthalate plasticisers. |
Approvals cover the material as supplied. Whether your finished assembly complies also depends on its design, cleaning regime and the other materials in it, so check against your own requirements.
Will it fit my slot?
Measure the slot width and depth. The leg is 2.0mm wide, so it grips best in a slot of about 1.8–2.0mm. The slot must be at least 5.1mm deep so the head can sit down flat; a deeper slot is fine. If the slot is shallower than 5mm, look at our 3mm × 6.5mm or 4mm × 6.5mm T seals instead, which have shorter legs.
How much do I need?
Add up the length of every slot and allow about 5% for trimming and joints. Example: a machine guard door 600mm × 400mm needs 2.0m, or about 2.1m with allowance, so one 25m coil seals 11 doors of that size.
Fitting tips
- Clear old seal, grease and grit out of the slot and let it dry
- Start partway along a straight side, not at a corner
- Press the leg in with your thumb or a small plastic roller as you go
- Lay the seal into corners rather than pulling it round: stretched silicone shrinks back and opens a gap
- Cut slightly long with a sharp knife and push the ends together; a dab of silicone adhesive keeps the joint closed
FAQ: frequently asked questions
What slot does it fit?
A slot about 1.8–2.0mm wide and at least 5.1mm deep. The head is 3.8mm wide, so it overlaps the slot by 0.9mm each side and covers the edges.
Which way up does it go?
The 2mm leg goes into the slot and the wider, flat head sits on the surface facing the door, lid or panel it seals against.
Can it be used near ovens and heaters?
It is rated to +180°C continuous, so it suits oven and warming-cabinet doors, drying equipment and heater housings where the seal stays at or below that temperature. For hotter positions, ask us about a higher-rated profile.
Is it safe near food or drinking water?
The compound is stated to meet FDA 21 CFR 177.2600 and EC 1935/2004 for food contact, and it is a WRAS approved material. We can send the declaration if your audit needs it.
How accurate are the dimensions?
The profile is extruded to ISO 3302-1 class E2, the normal tolerance class for extruded rubber sections. Check your slot against the drawing before ordering.
Will it flatten over time?
Silicone recovers well. This compound has a compression set of 31% after 22 hours at 175°C and 59% rebound resilience, so it keeps pushing back through repeated heat cycles.
What glue works with it?
Use a silicone adhesive or silicone sealant. Most general-purpose glues and contact adhesives will not bond to silicone rubber.
Can I buy a shorter length?
This listing is a full 25m coil. For a cut length or a large quantity, contact us for a quote.
Is every colour the same price?
Yes. All seven colours are £675.00 per 25m coil inc VAT (£27.00 per metre), so you can colour-code by area at no extra cost.
Complete your project
- Silicone T Seal Profile – 3mm x 6.5mm (shorter leg, shallower slots)
- Silicone T Seal Profile – 4mm x 6.5mm
- Silicone T-Section Seal – 10mm x 10mm
Not sure it will fit? Send us a photo or the slot width and depth and we will check it for you. Contact our team.
Product details
| SKU | IP-SITS-3.8X7.7-25M-BLK |
|---|---|
| Weight | 1.32 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone T Seal Profile – 3.8mm x 7.7mm – 25m Coil