Rubber & FoamSKU IP-SITS-5X5-H2.5-25M-BLK
Silicone T Seal Profile – 5mm x 5mm, 2.5mm Head, 2mm Leg, 50 Shore A – 25m Coil
A soft push-fit groove seal with a deep, wide sealing face. This silicone T seal profile is a solid 5mm x 5mm extrusion with a deep flat head (5mm wide, 2.5mm deep) on a narrow 2mm leg. Press the leg into a slot in your frame and the head stands 2.5mm proud, giving more compression travel than a thin-headed seal. The compound is a soft 50 Shore A silicone, so doors and lids close onto it with less force. Supplied as one continuous 25m coil in seven colours.
£675.00 inc VAT per 25m coil, which is £27.00 per metre.
Two 5mm x 5mm T seals are made. This one has the deep 2.5mm head, 2mm leg and soft 50 Shore A compound. For tight 1mm gaps or a wider 3mm slot, see the 5mm x 5mm T seal with a 1.5mm head and 3.1mm leg, 60 Shore A.
At a glance
- Flat head 5.0mm wide and 2.5mm deep
- Leg 2.0mm wide and 2.5mm long: a push fit in a slot about 1.8–2.0mm wide and at least 2.5mm deep
- Overall height 5.0mm; the head stands 2.5mm proud of the frame before compression
- Soft solid silicone rubber, 50 Shore A, with 640% elongation and 58% rebound
- Works from -50°C to +180°C without hardening or going brittle
- Food-contact compound (FDA 21 CFR 177.2600 and EC 1935/2004) and WRAS approved material
- 25m coil in black, white, translucent, red, green, blue or yellow, all the same price
Typical uses
- Lids, guards and inspection hatches on food processing, packaging and brewing equipment
- Lightweight doors and panels that need a low closing force, such as cabinet and enclosure doors
- Oven, warming cabinet and drying room doors with a closed gap of about 2mm
- HVAC access panels, duct inspection doors and air handling unit casings with a narrow 2mm slot
- Colour-coded seals for hygiene zones (blue, green, yellow, red)
Technical drawing
![]()
Full specification
| Property | Value | Test method |
|---|---|---|
| Dimensions | ||
| Profile type | Solid T section, square-cut flat head, straight leg | – |
| Overall width (head) | 5.0 mm | – |
| Overall height | 5.0 mm | – |
| Head depth | 2.5 mm | – |
| Leg (base) width | 2.0 mm | – |
| Leg length below head | 2.5 mm (reference, 5.0 − 2.5) | – |
| Shoulder each side | 1.5 mm (reference, (5.0 − 2.0) ÷ 2, leg centred) | – |
| Suggested slot | About 1.8–2.0 mm wide, at least 2.5 mm deep | Guidance |
| Dimensional tolerance | Class E2 | ISO 3302-1:2014 |
| Length per coil | 25 m, one continuous length | – |
| Material and physical properties | ||
| Material | Solid silicone rubber | – |
| Hardness | 50 Shore A | DIN ISO 48-4 |
| Density | 1.15 g/cm³ | DIN EN ISO 1183-1 A |
| Tensile strength | 12 N/mm² (12 MPa) | ISO 37 Type 1 |
| Elongation at break | 640 % | ISO 37 Type 1 |
| Tear strength | 27 N/mm | ASTM D624 B |
| Compression set | 34 % after 22 h at 175 °C | DIN ISO 815-1 Type B, Method A |
| Rebound resilience | 58 % | ISO 4662 |
| Service conditions | ||
| Working temperature | -50 °C to +180 °C | – |
| Environmental resistance | Ozone, UV, oxidation, weathering, corona discharge, cosmic and ionising radiation | – |
| Supply | ||
| Colours | Black, white, translucent, red, green, blue, yellow (same profile and price) | – |
| Unit of sale | 1 coil of 25 m (£27.00 per metre) | – |
| Approximate weight | About 0.50 kg per 25 m coil (calculated from section area and density) | Calculated |
Materials and compliance claims
These are the claims the manufacturer states for this exact profile and compound. Ask us for the certificate or declaration you need for your technical file.
| Claim | What it means for you |
|---|---|
| FDA 21 CFR 177.2600 | The compound meets the US rule for rubber articles intended for repeated contact with food. |
| EC 1935/2004 | The compound meets the EU framework regulation for materials intended to come into contact with food. |
| WRAS approved material | The material is listed as suitable for contact with drinking water in UK water fittings. |
| Free from TSE/BSE by-products | No animal-derived ingredients that carry TSE/BSE risk. |
| Phthalate free | Made without phthalate plasticisers. |
Approvals apply to the material as supplied. Whether a finished assembly complies also depends on your design, cleaning regime and other materials, so check against your own requirements.
Will it fit my groove?
This profile is made for a straight-sided slot about 1.8–2.0mm wide and at least 2.5mm deep. A slot a little narrower than the 2mm leg gives a firm grip fit; a slot the same width or slightly wider will still hold, but add a thin bead of silicone adhesive along the bottom, because the soft 50 Shore A leg grips less than a firmer grade. The 5mm head overhangs the slot by about 1.5mm on each side, so the frame needs at least that much flat land either side of the slot for the shoulders to sit on.
![]()
How much do I need?
Measure every slot and add about 5% for trimming and joints. Example: an oven door with a 600mm x 450mm groove needs 2.1m, so one 25m coil does about 11 doors with allowance.
Fitting tips
- Clean old seal and debris out of the slot and let it dry
- Start in the middle of a long side, not at a corner
- Press the leg in with your thumb or a plastic roller until the shoulders sit flat on the frame
- Do not stretch the seal as you go: soft silicone stretches easily, then shrinks back and opens gaps at the joints
- Cut slightly long with a sharp knife or shears and push the ends together for a tight butt joint; a dab of silicone adhesive keeps it closed
FAQ: frequently asked questions
Which way up does it go?
The 2mm leg goes into the slot. The flat 5mm face of the head faces outwards, towards the door, lid or panel that closes onto it.
How big a gap does it close?
The head stands 2.5mm proud of the frame. For a reliable seal, design for roughly 20–30% squeeze of the head, so a closed gap of about 1.75–2.0mm between the frame and the closing face. If your gap is only about 1mm, choose the 1.5mm-head version instead.
What slot size do I need?
A straight slot about 1.8–2.0mm wide and at least 2.5mm deep. Check your slot against the drawing before ordering, or send us the dimensions and we will check it.
What is the difference between the two 5mm x 5mm T seals?
Both are 5mm wide and 5mm tall. This one has a deeper 2.5mm head on a narrow 2mm leg in softer 50 Shore A, for bigger gaps, narrow slots and lower closing force. The other has a thin 1.5mm head on a wide 3.1mm leg in 60 Shore A, for tight gaps and wider slots.
Will it survive heat?
It is rated from -50°C to +180°C, so it suits ovens, warming cabinets, dryers and machinery that runs hot, as well as cold stores.
Is it safe near food or drinking water?
Yes. The compound is stated to meet FDA 21 CFR 177.2600 and EC 1935/2004 for food contact, and it is a WRAS approved material. Ask for the certificate if your audit needs it.
How do I cut and join it?
Cut square with a sharp knife or shears. Butt the ends together and bond with a silicone adhesive; at corners you can run the seal round in one piece if the slot radius allows, or mitre and bond it.
How tight are the dimensions?
The profile is extruded to ISO 3302-1 class E2, a standard tolerance class for extruded rubber.
Can I order a shorter length or a different colour mix?
This listing is a full 25m coil in one colour. For cut lengths, mixed colours or larger quantities, contact us for a quote.
Complete your project
- Silicone T Seal Profile – 5mm x 5mm, 1.5mm head, 3.1mm leg (60 Shore A)
- Silicone T Seal Profile – 4.3mm x 4.5mm (also soft 50 Shore A)
- Silicone T Seal Profile – 4.5mm x 5.8mm (domed head)
Not sure this profile matches your slot? Send us a photo or the slot dimensions and we will check it. Contact our team.
Product details
| SKU | IP-SITS-5X5-H2.5-25M-BLK |
|---|---|
| Weight | 1.32 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone T Seal Profile – 5mm x 5mm, 2.5mm Head, 2mm Leg, 50 Shore A – 25m Coil