Rubber & FoamSKU IP-SITS-4.5X5.8-25M-BLK
Silicone T Seal Profile – 4.5mm x 5.8mm – 25m Coil
A push-fit groove seal with a rounded sealing face. This silicone T seal profile is a solid 4.5mm x 5.8mm extrusion with a domed head (4.5mm wide, 2.5mm deep, top formed to a 3mm radius) on a 2.4mm wide leg. Press the leg into a slot in your frame and the head stands 2.5mm proud. Because the crown is curved, the closing door or lid meets a narrow line of contact first, so the seal beds in evenly even when the closing face is not perfectly parallel. Medium 60 Shore A silicone, supplied as one continuous 25m coil in seven colours.
£675.00 inc VAT per 25m coil, which is £27.00 per metre.
At a glance
- Domed head 4.5mm wide and 2.5mm deep overall, with a 3mm radius crown
- Leg 2.4mm wide and 3.3mm long: a push fit in a slot about 2.2–2.4mm wide and at least 3.3mm deep
- Overall height 5.8mm; the head stands 2.5mm proud of the frame before compression
- Solid silicone rubber, 60 Shore A, with 550% elongation and 59% rebound
- Works from -50°C to +180°C without hardening or going brittle
- Food-contact compound (FDA 21 CFR 177.2600 and EC 1935/2004) and WRAS approved material
- 25m coil in black, white, translucent, red, green, blue or yellow, all the same price
Typical uses
- Lids, guards and inspection hatches on food processing, packaging and brewing equipment
- Door seals on ovens, warming cabinets, drying rooms and heated enclosures
- HVAC access panels, duct inspection doors and air handling unit casings
- Glazing and panel infill seals in aluminium or stainless frames with a narrow slot
- Hatch and window seals on marine and vehicle bodywork
- Colour-coded seals for hygiene zones (blue, green, yellow, red)
Technical drawing
![]()
Full specification
| Property | Value | Test method |
|---|---|---|
| Dimensions | ||
| Profile type | Solid T section, domed head, straight leg | – |
| Overall width (head) | 4.5 mm | – |
| Overall height | 5.8 mm | – |
| Head depth (including dome) | 2.5 mm | – |
| Head crown radius | R 3 mm | – |
| Leg (base) width | 2.4 mm | – |
| Leg length below head | 3.3 mm (reference, 5.8 − 2.5) | – |
| Suggested slot | About 2.2–2.4 mm wide, at least 3.3 mm deep | Guidance |
| Dimensional tolerance | Class E2 | ISO 3302-1:2014 |
| Length per coil | 25 m, one continuous length | – |
| Material and physical properties | ||
| Material | Solid silicone rubber | – |
| Hardness | 60 Shore A | DIN ISO 48-4 |
| Density | 1.15 g/cm³ | DIN EN ISO 1183-1 A |
| Tensile strength | 11 N/mm² (11 MPa) | ISO 37 Type 1 |
| Elongation at break | 550 % | ISO 37 Type 1 |
| Tear strength | 26 N/mm | ASTM D624 B |
| Compression set | 31 % after 22 h at 175 °C | DIN ISO 815-1 Type B, Method A |
| Rebound resilience | 59 % | ISO 4662 |
| Service conditions | ||
| Working temperature | -50 °C to +180 °C | – |
| Environmental resistance | Ozone, UV, oxidation, weathering, corona discharge, cosmic and ionising radiation | – |
| Supply | ||
| Colours | Black, white, translucent, red, green, blue, yellow (same profile and price) | – |
| Unit of sale | 1 coil of 25 m (£27.00 per metre) | – |
Materials and compliance claims
These are the claims the manufacturer states for this exact profile and compound. Ask us for the certificate or declaration you need for your technical file.
| Claim | What it means for you |
|---|---|
| FDA 21 CFR 177.2600 | The compound meets the US rule for rubber articles intended for repeated contact with food. |
| EC 1935/2004 | The compound meets the EU framework regulation for materials intended to come into contact with food. |
| WRAS approved material | The material is listed as suitable for contact with drinking water in UK water fittings. |
| Free from TSE/BSE by-products | No animal-derived ingredients that carry TSE/BSE risk. |
| Phthalate free | Made without phthalate plasticisers. |
Approvals apply to the material as supplied. Whether a finished assembly complies also depends on your design, cleaning regime and other materials, so check against your own requirements.
Will it fit my groove?
This profile is made for a straight-sided slot about 2.2–2.4mm wide and at least 3.3mm deep. A slot a little narrower than the 2.4mm leg gives a firm grip fit; a slot the same width or slightly wider will still hold, but add a thin bead of silicone adhesive along the bottom. The 4.5mm head overhangs the slot by about 1.05mm on each side, so the frame needs at least that much flat land either side of the slot for the shoulders to sit on.
![]()
How much do I need?
Measure every slot and add about 5% for trimming and joints. Example: an oven door with a 600mm x 450mm groove needs 2.1m, so one 25m coil does about 11 doors with allowance.
Fitting tips
- Clean old seal and debris out of the slot and let it dry
- Start in the middle of a long side, not at a corner
- Press the leg in with your thumb or a plastic roller until the shoulders sit flat on the frame
- Do not stretch the seal as you go: stretched silicone shrinks back and opens gaps at the joints
- Cut slightly long with a sharp knife or shears and push the ends together for a tight butt joint; a dab of silicone adhesive keeps it closed
FAQ: frequently asked questions
Which way up does it go?
The 2.4mm leg goes into the slot. The rounded crown of the head faces outwards, towards the door, lid or panel that closes onto it.
How big a gap does it close?
The head stands 2.5mm proud of the frame. For a reliable seal, design for roughly 20–30% squeeze of the head, so a closed gap of about 1.8–2.0mm between the frame and the closing face.
What slot size do I need?
A straight slot about 2.2–2.4mm wide and at least 3.3mm deep. Check your slot against the drawing before ordering, or send us the dimensions and we will check it.
Why a domed head rather than a flat one?
The curved crown starts sealing on a narrow line and spreads as it compresses, so it copes better with slightly uneven or angled closing faces and needs less force to seal at first contact than a flat face of the same width.
Will it survive heat?
It is rated from -50°C to +180°C, so it suits ovens, warming cabinets, dryers and machinery that runs hot, as well as cold stores.
Is it safe near food or drinking water?
Yes. The compound is stated to meet FDA 21 CFR 177.2600 and EC 1935/2004 for food contact, and it is a WRAS approved material. Ask for the certificate if your audit needs it.
How do I cut and join it?
Cut square with a sharp knife or shears. Butt the ends together and bond with a silicone adhesive; at corners you can run the seal round in one piece if the slot radius allows, or mitre and bond it.
How tight are the dimensions?
The profile is extruded to ISO 3302-1 class E2, a standard tolerance class for extruded rubber.
Can I order a shorter length or a different colour mix?
This listing is a full 25m coil in one colour. For cut lengths, mixed colours or larger quantities, contact us for a quote.
Complete your project
- Silicone T Seal Profile – 4.3mm x 4.5mm (softer 50 Shore A, shorter leg)
- Silicone T Seal Profile – 4mm x 6.5mm (narrower head)
- Silicone T Seal Profile – 4mm x 8.5mm (deeper leg)
Not sure this profile matches your slot? Send us a photo or the slot dimensions and we will check it. Contact our team.
Product details
| SKU | IP-SITS-4.5X5.8-25M-BLK |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone T Seal Profile – 4.5mm x 5.8mm – 25m Coil