Rubber & FoamSKU IP-SITS-6.4X6.6-25M-BLK
Silicone T Seal Profile – 6.4mm x 6.6mm – 25m Coil
A solid silicone T seal with a flat 6.4mm-wide flange, a rounded crown along the middle of the top, and a plain 3.2mm leg. It stands 6.6mm tall overall. Push the leg into a slot about 3.2mm wide; the flange sits on the frame and covers both slot edges, and the crown stands up as the first point of contact for a closing door, lid or panel. The compound is a medium 60 Shore A silicone, rated -50°C to +180°C. Seven colours, all at the same price, and each coil is one unbroken 25m length.
£675.00 inc VAT per 25m coil, which is £27.00 per metre.
At a glance
- Flange 6.4mm wide and 2.0mm thick, with a domed crown rising 1.0mm above it (about 3.0mm wide at its base)
- Solid leg 3.2mm wide and 3.6mm long: a push fit in a straight slot about 3.0–3.2mm wide and at least 3.6mm deep
- 6.6mm overall height; the top of the crown stands 3.0mm proud of the frame before compression
- 1.6mm shoulder each side of the leg, so the flange covers both slot edges
- Silicone rubber, 60 Shore A: 550% elongation, 59% rebound, 31% compression set after 22 h at 175°C
- The manufacturer states the compound meets FDA 21 CFR 177.2600 and EC 1935/2004 for food contact, and it is a WRAS approved material
- Black, white, translucent, red, green, blue or yellow, all at the same price, held in stock
Typical uses
- Lids, hoppers and inspection hatches on food processing, packaging and brewing equipment
- Oven, prover and warming cabinet doors, where the crown takes up a door that does not close square
- Machine guards, electrical and control cabinets with a 3.2mm seal slot
- HVAC access panels, duct inspection doors, furnace and heated enclosure doors
- Hatches, windows and structural joints on marine, construction and vehicle bodywork
- Colour-coded seals for hygiene zones (red, green, blue, yellow)
Technical drawing
![]()
Full specification
| Property | Value | Test method |
|---|---|---|
| Dimensions | ||
| Profile type | Solid T section: flat flange with a domed central crown, straight centred leg | – |
| Overall width (flange) | 6.4 mm | – |
| Overall height | 6.6 mm | – |
| Flange thickness | 2.0 mm | – |
| Leg (base) width | 3.2 mm | – |
| Leg length below flange | 3.6 mm | – |
| Crown height above flange | 1.0 mm (reference, 6.6 − 2.0 − 3.6) | – |
| Crown width at base | About 3.0 mm (reference, scaled from the manufacturer's drawing) | – |
| Height standing proud of the frame | 3.0 mm (reference, flange + crown) | – |
| Shoulder each side | 1.6 mm (reference, leg centred) | – |
| Suits slot | Approx. 3.0–3.2 mm wide, at least 3.6 mm deep (our guidance) | – |
| Dimensional tolerance | Class E2 | ISO 3302-1:2014 |
| Length per coil | 25 m, one continuous length | – |
| Material and physical properties | ||
| Compound | Solid silicone rubber | – |
| Hardness | 60 Shore A | DIN ISO 48-4 |
| Density | 1.15 g/cm³ | DIN EN ISO 1183-1, method A |
| Tensile strength | 11 N/mm² (11 MPa) | ISO 37, type 1 |
| Elongation at break | 550 % | ISO 37, type 1 |
| Tear strength | 26 N/mm (26 kN/m) | ASTM D624, die B |
| Compression set | 31 % after 22 h at 175 °C | DIN ISO 815-1, type B, method A |
| Rebound resilience | 59 % | ISO 4662 |
| Service conditions | ||
| Working temperature | -50 °C to +180 °C | – |
| Environmental resistance | Ozone, UV, oxidation, weathering, corona discharge, cosmic and ionising radiation | – |
| Supply | ||
| Colours | Black, white, translucent, red, green, blue, yellow | – |
| Approx. weight | About 30 g per metre, about 0.76 kg per coil (calculated from section and density) | – |
| Unit of sale | 1 coil of 25 m (£27.00 per metre inc VAT) | – |
Materials and compliance
These are the claims the manufacturer makes in writing for this exact profile and compound. Ask us if your file needs the certificate or declaration.
| Claim | What it means for you |
|---|---|
| FDA 21 CFR 177.2600 | The compound meets the US rule for rubber articles in repeated contact with food. |
| EC 1935/2004 | The compound meets the EU framework regulation for materials that come into contact with food. |
| WRAS approved material | The material is accepted for contact with drinking water in UK water fittings. |
| Free from TSE/BSE by-products | No animal-derived ingredients that carry TSE/BSE risk. |
| Phthalate free | Made without phthalate plasticisers. |
The approvals cover the material as supplied. Whether your finished assembly complies also depends on its design, its cleaning regime and the other materials in it, so check it against your own requirements.
Will it fit my slot?
Measure the slot's width and depth. The leg is a plain 3.2mm, so it pushes in snugly in a slot of 3.0–3.2mm. A slightly wider slot works if you run a bead of silicone adhesive along it first. The slot should be at least 3.6mm deep so the flange sits down flat on the frame; a deeper slot is fine. The flange then covers 1.6mm of frame each side of the slot.
How much do I need?
Add up the length of every slot and allow about 5% for trimming and joints. For example, a 600mm × 400mm door needs 2.0m, or about 2.1m with the allowance, so one 25m coil seals 11 doors of that size.
Fitting tips
- Clear any old seal, grease and grit out of the slot, and let it dry
- Mark the length on the seal with a non-permanent pen before you cut
- Start partway along a straight side, not at a corner, and press the leg in with your thumb or a small plastic roller
- Lay the seal into corners rather than pulling it round them. Stretched silicone shrinks back and opens a gap.
- Smooth the flange flat on both sides of the slot so it bears evenly along its length
- Cut the end slightly long with a sharp knife and push the ends together; a dab of silicone adhesive keeps the joint closed
FAQ: frequently asked questions
What slot does it fit?
A straight-sided slot about 3.0–3.2mm wide and at least 3.6mm deep. The 3.2mm leg is a snug push fit in that range, and the 6.4mm flange overlaps the slot by 1.6mm each side.
Which way up does it go?
The plain 3.2mm leg goes into the slot. The flange sits on the frame with the domed crown facing the door, lid or panel it seals against.
What does the domed crown do?
The crown touches the closing panel first, along a narrow line, so the seal makes contact even if the door sits slightly out of square. As the door closes further the crown squashes down and the contact band widens towards the flange.
How hard is it?
60 Shore A, a medium silicone. It is soft enough to seal with normal closing force and firm enough to hold its shape in the slot. Its 59% rebound means it springs back each time the door opens.
Can it be used near ovens and heaters?
It is rated to +180°C. That suits oven, prover and warming-cabinet doors, drying equipment and heater housings, as long as the seal itself stays at or below that temperature. It stays flexible down to -50°C.
Is it safe near food or drinking water?
The manufacturer states the compound meets FDA 21 CFR 177.2600 and EC 1935/2004 for food contact, and it is a WRAS approved material. We can send the declaration if your audit needs it.
Will it stay in the slot without glue?
In a 3.0–3.2mm slot the leg grips by friction, which is enough for most lids and doors. On a sliding door, a vibrating machine or a slot that is a little oversize, run a thin bead of silicone adhesive in the slot first.
How accurate are the dimensions?
The profile is extruded to ISO 3302-1 class E2, the normal tolerance class for extruded rubber sections. Check your slot against the drawing before you order.
Will it flatten over time?
It has a compression set of 31% after 22 hours at 175°C. That is a hot, demanding test; at normal room or warm service temperatures the seal keeps springing back for a long time.
How do I cut and join it?
Cut it with a sharp knife or heavy shears. To join it, use a silicone adhesive or silicone sealant; most general-purpose glues and contact adhesives will not bond to silicone rubber.
Is every colour the same price?
Yes. All seven colours cost £675.00 per 25m coil inc VAT (£27.00 per metre).
Complete your project
- Silicone T Seal Profile – 6.1mm x 6.5mm (deep flat head, 3.6mm leg, soft 40 Shore A)
- Silicone T Seal Profile – 5mm x 8.5mm (same 3.2mm leg, narrower head, 50 Shore A)
- Silicone T Seal Profile – 5.8mm x 7.5mm (domed head, ribbed leg)
Not sure it will fit? Send us a photo, or the width and depth of the slot, and we will check it for you. Contact our team.
Product details
| SKU | IP-SITS-6.4X6.6-25M-BLK |
|---|---|
| Weight | 2.2 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone T Seal Profile – 6.4mm x 6.6mm – 25m Coil