Rubber & FoamSKU IP-SITS-5X8.5-25M-BLK
Silicone T Seal Profile – 5mm x 8.5mm – 25m Coil
A solid silicone T seal with a 5mm-wide, 2.5mm-thick head on a 3.2mm leg, 8.5mm tall overall. Push the leg into a slot about 3.0–3.2mm wide and the flat head sits on the surface, closing the gap against dust, splash, draughts and heat. The compound is a soft 50 Shore A silicone, so the head compresses easily under a light door or lid. Seven colours, all at the same price, and each coil is one unbroken 25m length.
At a glance
- Head 5.0mm wide × 2.5mm thick; leg 3.2mm wide; 8.5mm overall height (6.0mm of leg below the head)
- 0.9mm shoulder each side of the leg, so the head covers both slot edges
- Soft solid silicone rubber, 50 Shore A, working range -50°C to +180°C
- The manufacturer states the compound meets FDA 21 CFR 177.2600 and EC 1935/2004 for food contact. It is a WRAS approved material.
- Black, white, translucent, red, green, blue or yellow, all at the same price
- Held in stock in every colour
Typical uses
- Slot seals in machine guards, enclosures and aluminium profile frames
- Access doors on air handling units, fan coil housings and ductwork
- Inspection hatches on food, bakery and packaging machinery
- Lids and doors on ovens, provers, warming cabinets and dryers up to +180°C
- Catering equipment: refrigeration trims and counter joints
- Marine hatches and outdoor enclosures, where UV and ozone crack other rubbers
- Colour-coded seals for hygiene zones (red, green, blue, yellow)
Technical drawing
![]()
Full specification
| Property | Value | Test method |
|---|---|---|
| Dimensions | ||
| Profile type | Solid T section, square-cut head, centred leg | – |
| Overall height | 8.5 mm | – |
| Head width | 5.0 mm | – |
| Head thickness | 2.5 mm | – |
| Leg width (base thickness) | 3.2 mm | – |
| Leg length below head | 6.0 mm (reference, 8.5 − 2.5) | – |
| Shoulder each side | 0.9 mm (reference, leg centred) | – |
| Suits slot | Approx. 3.0–3.2 mm wide, at least 6 mm deep | – |
| Dimensional tolerance | Class E2 | ISO 3302-1:2014 |
| Length per coil | 25 m, one continuous length | – |
| Material and physical properties | ||
| Compound | Solid silicone rubber | – |
| Hardness | 50 Shore A | DIN ISO 48-4 |
| Density | 1.15 g/cm³ | DIN EN ISO 1183-1, method A |
| Tensile strength | 12 N/mm² (12 MPa) | ISO 37, type 1 |
| Elongation at break | 640 % | ISO 37, type 1 |
| Tear strength | 27 N/mm (27 kN/m) | ASTM D624, die B |
| Compression set | 34 % after 22 h at 175 °C | DIN ISO 815-1, type B, method A |
| Rebound resilience | 58 % | ISO 4662 |
| Service conditions | ||
| Working temperature | -50 °C to +180 °C | – |
| Environmental resistance | Ozone, UV, oxidation, weathering, corona discharge, cosmic and ionising radiation | – |
| Supply | ||
| Colours | Black, white, translucent, red, green, blue, yellow | – |
| Approx. weight | About 36 g per metre, about 0.9 kg per coil (calculated from section and density) | – |
| Unit of sale | 1 coil of 25 m (£27.00 per metre inc VAT) | – |
Materials and compliance
These are the claims the manufacturer makes in writing for this exact profile and compound. Ask us if your file needs the certificate or declaration.
| Claim | What it means for you |
|---|---|
| FDA 21 CFR 177.2600 | The compound meets the US rule for rubber articles in repeated contact with food. |
| EC 1935/2004 | The compound meets the EU framework regulation for materials that come into contact with food. |
| WRAS approved material | The material is accepted for contact with drinking water in UK water fittings. |
| Free from TSE/BSE by-products | No animal-derived ingredients that carry TSE/BSE risk. |
| Phthalate free | Made without phthalate plasticisers. |
The approvals cover the material as supplied. Whether your finished assembly complies also depends on its design, its cleaning regime and the other materials in it, so check it against your own requirements.
Will it fit my slot?
Measure the slot's width and depth. The leg is 3.2mm wide, so it grips best in a slot of about 3.0–3.2mm. The slot should be at least 6mm deep so the head can sit down flat; a deeper slot is fine. If your slot is nearer 2.7mm wide, our 4.5mm × 8.5mm T seal with a 2.7mm leg is a closer fit, and for a 2.2mm slot use the 4mm × 8.5mm.
How much do I need?
Add up the length of every slot and allow about 5% for trimming and joints. For example, a 600mm × 400mm guard door needs 2.0m, or about 2.1m with the allowance, so one 25m coil seals 11 doors of that size.
Fitting tips
- Clear any old seal, grease and grit out of the slot, and let it dry
- Start partway along a straight side, not at a corner
- Press the leg in with your thumb or a small plastic roller as you go
- Lay the seal into corners rather than pulling it round them. Stretched silicone shrinks back and opens a gap.
- Cut the end slightly long with a sharp knife and push the ends together; a dab of silicone adhesive keeps the joint closed
FAQ: frequently asked questions
What slot does it fit?
A slot about 3.0–3.2mm wide and at least 6mm deep. The head is 5mm wide, so it overlaps the slot by 0.9mm each side and covers the edges.
Which way up does it go?
The 3.2mm leg goes into the slot, and the wider head sits on the surface, facing the door, lid or panel it seals against.
How hard is it?
50 Shore A, a soft silicone. It squashes easily under a light lid or a hand-closed door, so it suits doors with low closing force. For a firmer seal of a similar size, see the 70 Shore A 4.5mm × 8.5mm profile.
Can it be used near ovens and heaters?
It is rated to +180°C continuous. That suits oven and warming-cabinet doors, drying equipment and heater housings, as long as the seal itself stays at or below that temperature. It stays flexible down to -50°C.
Is it safe near food or drinking water?
The manufacturer states the compound meets FDA 21 CFR 177.2600 and EC 1935/2004 for food contact, and it is a WRAS approved material. We can send the declaration if your audit needs it.
How accurate are the dimensions?
The profile is extruded to ISO 3302-1 class E2, the normal tolerance class for extruded rubber sections. Check your slot against the drawing before you order.
Will it flatten over time?
It has a compression set of 34% after 22 hours at 175°C and a rebound resilience of 58%, so it springs back well and keeps sealing through repeated heat cycles.
How do I cut and join it?
Cut it with a sharp knife or shears. To join it, use a silicone adhesive or silicone sealant; most general-purpose glues and contact adhesives will not bond to silicone rubber.
Is every colour the same price?
Yes. All seven colours cost £675.00 per 25m coil inc VAT (£27.00 per metre).
Complete your project
- Silicone T Seal Profile – 4.5mm x 8.5mm (2.7mm leg, 70 Shore A)
- Silicone T Seal Profile – 4mm x 8.5mm (2.2mm leg)
- Silicone T Seal Profile – 5mm x 5.9mm (shorter leg)
Not sure it will fit? Send us a photo, or the width and depth of the slot, and we will check it for you. Contact our team.
Product details
| SKU | IP-SITS-5X8.5-25M-BLK |
|---|---|
| Weight | 2.2 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone T Seal Profile – 5mm x 8.5mm – 25m Coil