Rubber & FoamSKU IP-SITS-6.4X7-25M-BLK
Silicone T Seal Profile – 6.4mm x 7mm – 25m Coil
A firm, heavy-section T seal for 3.5mm slots that need a little more depth. This silicone T seal profile is a solid 6.4mm x 7mm extrusion with a deep, square-edged flat head (6.4mm wide, 3.2mm deep) on a thick 3.6mm wide leg that runs 3.8mm below the head. The long, heavy leg fills a 3.5mm-class slot almost completely and grips along its full depth, so the seal stays put on vibrating machinery and frequently opened doors. The head stands 3.2mm proud of the frame and gives the closing door, lid or panel a full 6.4mm flat contact band. In a medium 60 Shore A silicone, it holds a crisp, straight line and recovers well after compression. It comes as one continuous 25m coil in seven colours.
£675.00 inc VAT per 25m coil, which is £27.00 per metre.
At a glance
- Flat head 6.4mm wide and 3.2mm deep, square edges, 1.4mm shoulder each side of the leg
- Solid leg 3.6mm wide and 3.8mm long: a push fit in a straight slot about 3.4–3.6mm wide and at least 3.8mm deep
- Overall height 7mm; the head stands 3.2mm proud of the frame before compression
- Medium 60 Shore A silicone: 11 N/mm² tensile, 550% elongation, 59% rebound, 31% compression set after 22 h at 175°C
- Works from -50°C to +180°C without hardening or going brittle
- Food-contact compound (FDA 21 CFR 177.2600 and EC 1935/2004) and WRAS approved material
- 25m coil in black, white, translucent, red, green, blue or yellow, all the same price
Typical uses
- Lids, hoppers and inspection hatches on food processing, packaging and brewing equipment
- Oven, proving cabinet and warming cupboard doors running up to +180°C
- Machine guards and electrical or control cabinets with a deeper 3.5mm seal slot
- HVAC access panels, duct inspection doors, furnace and heated enclosure doors
- Hatch, window and structural joint seals on marine, construction and vehicle bodywork
- Electronics bays and trim joints where a firm, neat edge matters
- Colour-coded seals for hygiene zones (blue, green, yellow, red)
Technical drawing
![]()
Full specification
| Property | Value | Test method |
|---|---|---|
| Dimensions | ||
| Profile type | Solid T section, flat square-edged head, straight solid leg | – |
| Overall width (head) | 6.4 mm | – |
| Overall height | 7.0 mm | – |
| Head depth | 3.2 mm | – |
| Leg (base) width | 3.6 mm | – |
| Leg length below head | 3.8 mm (reference, 7.0 − 3.2) | – |
| Shoulder overhang each side | 1.4 mm (reference, (6.4 − 3.6) ÷ 2) | – |
| Suggested slot | About 3.4–3.6 mm wide, at least 3.8 mm deep | Guidance |
| Dimensional tolerance | Class E2 | ISO 3302-1:2014 |
| Length per coil | 25 m, one continuous length | – |
| Material and physical properties | ||
| Material | Solid silicone rubber | – |
| Hardness | 60 Shore A (medium) | DIN ISO 48-4 |
| Density | 1.15 g/cm³ | DIN EN ISO 1183-1 A |
| Tensile strength | 11 N/mm² (11 MPa) | ISO 37 Type 1 |
| Elongation at break | 550 % | ISO 37 Type 1 |
| Tear strength | 26 N/mm | ASTM D624 B |
| Compression set | 31 % after 22 h at 175 °C | DIN ISO 815-1 Type B, Method A |
| Rebound resilience | 59 % | ISO 4662 |
| Service conditions | ||
| Working temperature | -50 °C to +180 °C | – |
| Environmental resistance | Ozone, UV, oxidation, weathering, corona discharge, cosmic and ionising radiation | – |
| Supply | ||
| Colours | Black, white, translucent, red, green, blue, yellow (same profile and price) | – |
| Unit of sale | 1 coil of 25 m (£27.00 per metre) | – |
Materials and compliance claims
These are the claims the manufacturer makes for this exact profile and compound. Ask us for the certificate or declaration you need for your technical file.
| Claim | What it means for you |
|---|---|
| FDA 21 CFR 177.2600 | The compound meets the US rule for rubber articles intended for repeated contact with food. |
| EC 1935/2004 | The compound meets the EU framework regulation for materials intended to come into contact with food. |
| WRAS approved material | The material is listed as suitable for contact with drinking water in UK water fittings. |
| Free from TSE/BSE by-products | No animal-derived ingredients that carry TSE/BSE risk. |
| Phthalate free | Made without phthalate plasticisers. |
Approvals apply to the material as supplied. Whether a finished assembly complies also depends on your design, cleaning regime and other materials, so check against your own requirements.
Will it fit my groove?
This profile is made for a straight-sided slot about 3.4–3.6mm wide and at least 3.8mm deep. The 60 Shore A leg pushes into a slot a little under 3.6mm and grips firmly along its full length. In a slot that is exactly 3.6mm or a little wider, add a thin bead of silicone adhesive along the bottom. If the slot is shallower than 3.8mm, the head will not sit flat, so trim the leg or choose a shorter profile such as the 6.1mm x 6.5mm. The frame needs at least 1.4mm of flat land either side of the slot for the shoulders to sit on.
![]()
How much do I need?
Measure every slot and add about 5% for trimming and joints. For example, a cabinet door with a 600mm x 450mm groove needs 2.1m of seal, so one 25m coil covers about 11 doors with that allowance.
Fitting tips
- Clean old seal and debris out of the slot and let it dry
- Start in the middle of a long side, not at a corner
- Press the leg in with your thumb or a plastic roller until the shoulders sit flat on the frame along the whole run
- Do not stretch the seal as you go: stretched silicone shrinks back later and opens gaps at the joints
- Cut slightly long with a sharp knife or shears and push the ends together for a tight butt joint; a dab of silicone adhesive keeps it closed
FAQ: frequently asked questions
Which way up does it go?
The 3.6mm leg goes into the slot. The flat 6.4mm face of the head faces outwards, towards the door, lid or panel that closes onto it.
How big a gap does it close?
The head stands 3.2mm proud of the frame. As a guide for a 60 Shore A seal, design for about 15–25% squeeze of the head, which leaves a closed gap of roughly 2.4–2.7mm between the frame and the closing face.
What slot size do I need?
A straight slot about 3.4–3.6mm wide and at least 3.8mm deep, with at least 1.4mm of flat frame either side. Check your slot against the drawing before ordering, or send us the dimensions and we will check it.
How is it different from the 6.1mm x 6.5mm T seal?
Both have a 3.2mm deep head and a 3.6mm leg. This one has a slightly wider 6.4mm head and a longer 3.8mm leg (against 3.3mm), so it needs a deeper slot and holds more securely. It is also a firmer 60 Shore A compound, where the 6.1mm x 6.5mm is a soft 40 Shore A.
Is 60 Shore A soft or hard?
It is a medium hardness, roughly like a car tyre tread or a pencil eraser. It compresses under normal closing force, holds a crisp edge and resists being pulled out of the slot. If you need a very soft seal for light doors or uneven faces, choose a 40 Shore A profile.
Will it survive heat?
It is rated from -50°C to +180°C, so it suits ovens, warming cabinets, dryers and machinery that runs hot, as well as cold stores.
Is it safe near food or drinking water?
Yes. The manufacturer states that the compound meets FDA 21 CFR 177.2600 and EC 1935/2004 for food contact, and that it is a WRAS approved material. Ask for the certificate if your audit needs it.
How do I cut and join it?
Cut square with a sharp knife or shears. Butt the ends together and bond with a silicone adhesive. For crisp corners, mitre and bond them rather than bending the seal round a tight radius.
How tight are the dimensions?
The profile is extruded to ISO 3302-1 class E2, a standard tolerance class for extruded rubber.
Can I order a shorter length or a different colour mix?
This listing is a full 25m coil in one colour. For cut lengths, mixed colours or larger quantities, contact us for a quote.
Complete your project
- Silicone T Seal Profile – 6.1mm x 6.5mm (same head depth and leg width, shorter leg, soft 40 Shore A)
- Silicone T Seal Profile – 6mm x 8mm (4mm leg, 60 Shore A)
- Silicone T Seal Profile – 6mm x 6.5mm (slim 2mm leg, 60 Shore A)
Not sure this profile matches your slot? Send us a photo or the slot dimensions and we will check it. Contact our team.
Product details
| SKU | IP-SITS-6.4X7-25M-BLK |
|---|---|
| Weight | 2.43 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone T Seal Profile – 6.4mm x 7mm – 25m Coil