Rubber & FoamSKU IP-SITS-6X6.5-25M-BLK
Silicone T Seal Profile – 6mm x 6.5mm – 25m Coil
A deep-anchoring push-fit seal for slots that need a secure grip. This silicone T seal profile is a solid 6mm x 6.5mm extrusion with a square-edged flat head (6mm wide, 2mm deep) on a 2mm wide, 4.5mm long leg. The long leg sits deep in the slot so the seal stays put on doors and lids that open all day, while the head stands 2mm proud and gives the closing face a full 6mm contact band, with 2mm shoulders covering the frame either side. At 60 Shore A it is a mid-hardness silicone: soft enough to seal with modest closing force, firm enough to keep a clean square line. Supplied as one continuous 25m coil in seven colours.
£675.00 inc VAT per 25m coil, which is £27.00 per metre.
At a glance
- Flat head 6mm wide and 2mm deep, square edges, 2mm shoulder each side of the leg
- Leg 2mm wide and 4.5mm long: a push fit in a slot about 1.7–2.0mm wide and at least 4.5mm deep
- Overall height 6.5mm; the head stands 2mm proud of the frame before compression
- Mid-hardness solid silicone, 60 Shore A, with 550% elongation, 59% rebound and a low 31% compression set
- Works from -50°C to +180°C without hardening or going brittle
- Food-contact compound (FDA 21 CFR 177.2600 and EC 1935/2004) and WRAS approved material
- 25m coil in black, white, translucent, red, green, blue or yellow, all the same price
Typical uses
- Lids, guards and inspection hatches on food processing, packaging and brewing equipment
- Oven, proving cabinet and drying room doors that are opened and closed repeatedly at temperature
- HVAC access panels, duct inspection doors and heated enclosures
- Glazing and infill panels in deep-slotted aluminium or stainless frames
- Hatch, window and trim seals on marine and vehicle bodywork
- Colour-coded seals for hygiene zones (blue, green, yellow, red)
Technical drawing
![]()
Full specification
| Property | Value | Test method |
|---|---|---|
| Dimensions | ||
| Profile type | Solid T section, flat square-edged head, straight leg | – |
| Overall width (head) | 6.0 mm | – |
| Overall height | 6.5 mm | – |
| Head depth | 2.0 mm | – |
| Leg (base) width | 2.0 mm | – |
| Leg length below head | 4.5 mm (reference, 6.5 − 2.0) | – |
| Shoulder overhang each side | 2.0 mm (reference, (6.0 − 2.0) ÷ 2) | – |
| Suggested slot | About 1.7–2.0 mm wide, at least 4.5 mm deep | Guidance |
| Dimensional tolerance | Class E2 | ISO 3302-1:2014 |
| Length per coil | 25 m, one continuous length | – |
| Material and physical properties | ||
| Material | Solid silicone rubber | – |
| Hardness | 60 Shore A | DIN ISO 48-4 |
| Density | 1.15 g/cm³ | DIN EN ISO 1183-1 A |
| Tensile strength | 11 N/mm² (11 MPa) | ISO 37 Type 1 |
| Elongation at break | 550 % | ISO 37 Type 1 |
| Tear strength | 26 N/mm | ASTM D624 B |
| Compression set | 31 % after 22 h at 175 °C | DIN ISO 815-1 Type B, Method A |
| Rebound resilience | 59 % | ISO 4662 |
| Service conditions | ||
| Working temperature | -50 °C to +180 °C | – |
| Environmental resistance | Ozone, UV, oxidation, weathering, corona discharge, cosmic and ionising radiation | – |
| Supply | ||
| Colours | Black, white, translucent, red, green, blue, yellow (same profile and price) | – |
| Unit of sale | 1 coil of 25 m (£27.00 per metre) | – |
Materials and compliance claims
These are the claims the manufacturer states for this exact profile and compound. Ask us for the certificate or declaration you need for your technical file.
| Claim | What it means for you |
|---|---|
| FDA 21 CFR 177.2600 | The compound meets the US rule for rubber articles intended for repeated contact with food. |
| EC 1935/2004 | The compound meets the EU framework regulation for materials intended to come into contact with food. |
| WRAS approved material | The material is listed as suitable for contact with drinking water in UK water fittings. |
| Free from TSE/BSE by-products | No animal-derived ingredients that carry TSE/BSE risk. |
| Phthalate free | Made without phthalate plasticisers. |
Approvals apply to the material as supplied. Whether a finished assembly complies also depends on your design, cleaning regime and other materials, so check against your own requirements.
Will it fit my groove?
This profile is made for a narrow, straight-sided slot about 1.7–2.0mm wide and at least 4.5mm deep. At 60 Shore A the leg squeezes slightly into a slot a touch under 2mm and grips along its full 4.5mm length. In a slot that is exactly 2mm or a little wider, add a thin bead of silicone adhesive along the bottom. If your slot is shallower than 4.5mm the head will not seat flat; trim the leg or choose a shorter profile such as the 6mm x 4.5mm. The frame needs at least 2mm of flat land either side of the slot for the shoulders to sit on.
![]()
How much do I need?
Measure every slot and add about 5% for trimming and joints. Example: a cabinet door with a 600mm x 450mm groove needs 2.1m, so one 25m coil does about 11 doors with allowance.
Fitting tips
- Clean old seal and debris out of the slot and let it dry
- Start in the middle of a long side, not at a corner
- Press the leg in with your thumb or a plastic roller until the shoulders sit flat on the frame along the whole run
- Do not stretch the seal as you go: stretched silicone shrinks back and opens gaps at the joints
- Cut slightly long with a sharp knife or shears and push the ends together for a tight butt joint; a dab of silicone adhesive keeps it closed
FAQ: frequently asked questions
Which way up does it go?
The 2mm leg goes into the slot. The flat 6mm face of the head faces outwards, towards the door, lid or panel that closes onto it.
How big a gap does it close?
The head stands 2mm proud of the frame. As a guide for a 60 Shore A seal, design for about 20–30% squeeze of the head: a closed gap of roughly 1.4–1.6mm between the frame and the closing face. For a larger gap, choose a taller-headed profile.
What slot size do I need?
A straight slot about 1.7–2.0mm wide and at least 4.5mm deep, with at least 2mm of flat frame either side. Check your slot against the drawing before ordering, or send us the dimensions and we will check it.
How is it different from the 6mm x 4.5mm T seal?
Same 6mm head width and 2mm leg width, but this leg is 4.5mm long instead of 2mm, so it anchors far deeper, and the head is 2mm deep instead of 2.5mm. It is also a softer 60 Shore A compound with a much lower compression set (31% against 78%), so it recovers better after long periods of squeeze and heat.
Is 60 Shore A soft or hard?
It is a medium hardness, roughly like a pencil eraser. It seals with moderate closing force, recovers well (59% rebound, 31% compression set after 22 hours at 175°C) and still holds a square, tidy edge.
Will it survive heat?
It is rated from -50°C to +180°C, so it suits ovens, warming cabinets, dryers and machinery that runs hot, as well as cold stores.
Is it safe near food or drinking water?
Yes. The compound is stated to meet FDA 21 CFR 177.2600 and EC 1935/2004 for food contact, and it is a WRAS approved material. Ask for the certificate if your audit needs it.
How do I cut and join it?
Cut square with a sharp knife or shears. Butt the ends together and bond with a silicone adhesive. For crisp corners, mitre and bond them rather than bending the seal round a tight radius.
How tight are the dimensions?
The profile is extruded to ISO 3302-1 class E2, a standard tolerance class for extruded rubber.
Can I order a shorter length or a different colour mix?
This listing is a full 25m coil in one colour. For cut lengths, mixed colours or larger quantities, contact us for a quote.
Complete your project
- Silicone T Seal Profile – 6mm x 4.5mm (same head width, short 2mm leg)
- Silicone T Seal Profile – 6mm x 5.2mm (40 or 80 Shore A)
- Silicone T Seal Profile – 7.5mm x 6.5mm (same height, wider head)
- Silicone T Seal Profile – 4mm x 6.5mm (same height, narrower head)
Not sure this profile matches your slot? Send us a photo or the slot dimensions and we will check it. Contact our team.
Product details
| SKU | IP-SITS-6X6.5-25M-BLK |
|---|---|
| Weight | 1.76 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone T Seal Profile – 6mm x 6.5mm – 25m Coil