Rubber & FoamSKU IP-SITS-10X8-L4-25M-BLK
Silicone T Seal Profile – 10mm x 8mm, 4mm Leg (2.6mm Head) – 60 Shore A – 25m Coil
A solid silicone T seal with a wide, thin head: 10mm across and 2.6mm deep, on a 4mm push-in leg, 8mm tall overall. Press the leg into a slot about 3.8–4.0mm wide and the flat head lies across the frame, covering 3.0mm of face either side of the slot. The door, lid or panel closes onto that broad, low head, so you get a wide contact band without a tall seal that stops the door shutting. Moulded in 60 Shore A silicone for -50°C to +180°C, it comes in seven colours, all at the same price, in one unbroken 25m coil.
Check the leg before you order. We stock two different 10mm × 8mm silicone T seals. This one has a 4mm leg and 2.6mm head. The other has a 3mm leg and 3.0mm head: see the 3mm leg version.
At a glance
- Head 10.0mm wide × 2.6mm deep; leg 4mm wide; 8.0mm overall (5.4mm of leg below the head)
- 3.0mm shoulder each side of the leg, so the head covers both slot edges with room to spare
- 60 Shore A solid silicone, working range -50°C to +180°C
- The manufacturer states the compound meets FDA 21 CFR 177.2600 and EC 1935/2004 for food contact, and it is a WRAS approved material
- Black, white, translucent, red, green, blue or yellow, all £675.00 per 25m coil (£27.00 per metre)
- Held in stock in every colour
Which 10 × 8mm T seal do I need?
| 4mm leg version | 3mm leg version | |
|---|---|---|
| Fits a slot about | 3.8–4.0mm wide, at least 5.4mm deep | 2.8–3.0mm wide, at least 5.0mm deep |
| Head | 10.0 × 2.6mm (lower) | 10.0 × 3.0mm (slightly taller) |
| Shoulder each side | 3.0mm | 3.5mm |
| Hardness and compound | 60 Shore A silicone | 60 Shore A silicone (same compound) |
| Our part number | IP-SITS-10X8-L4-25M | IP-SITS-10X8-L3-25M |
| This listing | View |
The material is identical; only the leg and head depth differ. Choose by the width of your slot, because the leg must grip it. A 4mm leg will not go into a 3mm slot, and a 3mm leg will be loose in a 4mm slot.
Typical uses
- Perimeter seals on oven, prover and warming-cabinet doors up to +180°C
- Access doors and inspection hatches on food, bakery and packaging machinery
- Joints between stainless cabinets, panels and enclosures in food and pharma plants
- Machine guards and aluminium profile frames with a routed or extruded slot
- Air handling units, duct access panels and heater housings
- Outdoor and marine enclosures, where UV and ozone crack ordinary rubbers
- Colour-coded seals for hygiene zones (red, green, blue, yellow) or visible inspection (white, translucent)
Technical drawing
![]()
Full specification
| Property | Value | Test method |
|---|---|---|
| Dimensions | ||
| Profile type | Solid T section, square-cut flat head, centred leg | – |
| Overall height | 8.0 mm | – |
| Head width | 10.0 mm | – |
| Head depth | 2.6 mm | – |
| Leg width (base thickness) | 4.0 mm | – |
| Leg length below head | 5.4 mm (reference, 8.0 − 2.6) | – |
| Shoulder each side | 3.0 mm (reference, leg centred) | – |
| Suits slot (our guidance) | Approx. 3.8–4.0 mm wide, at least 5.4 mm deep | – |
| Dimensional tolerance | Class E2 | ISO 3302-1:2014 |
| Length per coil | 25 m, one continuous length | – |
| Material and physical properties | ||
| Compound | Solid silicone rubber | – |
| Hardness | 60 Shore A | DIN ISO 48-4 |
| Density | 1.15 g/cm³ | DIN EN ISO 1183-1, method A |
| Tensile strength | 11 N/mm² (11 MPa) | ISO 37, type 1 |
| Elongation at break | 550 % | ISO 37, type 1 |
| Tear strength | 26 N/mm (26 kN/m) | ASTM D624, die B |
| Compression set | 31 % after 22 h at 175 °C | DIN ISO 815-1, type B, method A |
| Rebound resilience | 59 % | ISO 4662 |
| Service conditions | ||
| Working temperature | -50 °C to +180 °C | – |
| Environmental resistance | Ozone, UV, oxidation, weathering, corona discharge, cosmic and ionising radiation | – |
| Supply | ||
| Colours | Black, white, translucent, red, green, blue, yellow | – |
| Approx. weight | About 55 g per metre, 1.37 kg per coil (calculated from the 47.6 mm² section and density) | – |
| Unit of sale | 1 coil of 25 m (£27.00 per metre inc VAT) | – |
| Our part number | IP-SITS-10X8-L4-25M-<colour> | – |
Materials and compliance
These are the claims the manufacturer makes in writing for this profile. Ask us if your file needs the declaration.
| Claim | What it means for you |
|---|---|
| FDA 21 CFR 177.2600 | The compound meets the US rule for rubber articles in repeated contact with food. |
| EC 1935/2004 | The compound meets the EU framework regulation for materials that come into contact with food. |
| WRAS approved material | The material is accepted for contact with drinking water in UK water fittings. |
| Free from TSE/BSE by-products | No animal-derived ingredients that carry TSE/BSE risk. |
| Phthalate free | Made without phthalate plasticisers. |
The approvals cover the material as supplied. Whether your finished assembly complies also depends on its design, its cleaning regime and the other materials in it, so check it against your own requirements.
Will it fit my slot?
Measure the slot's width and depth. The leg is 4mm wide, so it grips best in a slot of about 3.8–4.0mm. The slot should be at least 5.4mm deep so the head can sit down on the frame; deeper is fine. The face either side of the slot needs about 3.0mm of flat land for the head to rest on. If your slot is nearer 3mm wide, you need the 3mm leg version instead.
How much do I need?
Add up the length of every slot and allow about 5% for trimming and joints. For example, a 600mm × 400mm oven or guard door needs 2.0m, or about 2.1m with the allowance, so one 25m coil seals 11 doors of that size.
Fitting tips
- Clear old seal, grease and grit out of the slot and let it dry
- Start partway along a straight side, not at a corner
- Press the leg in with your thumb or a small plastic roller as you go. A drop of soapy water helps it slide into a tight slot.
- If the slot is loose or the seal must not move, run a bead of silicone adhesive into the slot first
- Lay the seal into corners rather than pulling it round them; stretched silicone shrinks back and opens a gap. On tight corners, mitre the head and keep the leg continuous.
- Cut the end slightly long with a sharp knife and push the ends together; a dab of silicone adhesive keeps the joint closed
FAQ: frequently asked questions
What slot does it fit?
A slot about 3.8–4.0mm wide and at least 5.4mm deep. The head is 10mm wide, so it overlaps the slot by 3.0mm each side.
Which way up does it go?
The 4mm leg goes into the slot. The wide, flat head sits on the frame and faces the door, lid or panel it seals against.
What is the difference between your two 10mm × 8mm T seals?
The leg and the head depth. This one has a 4mm leg and a 2.6mm head. The other has a 3mm leg and a 3.0mm head. Both are the same 60 Shore A silicone. They are not interchangeable: pick the one whose leg matches your slot.
How much gap will it seal?
The head stands 2.6mm proud of the frame. It seals best where the closed door sits about 1–2mm above the frame, so the head is squeezed by roughly a third to a half of its depth. For bigger gaps, choose a taller profile.
Can it be used near ovens and heaters?
Yes. It is rated -50°C to +180°C, which suits oven, prover and warming-cabinet doors, dryers and heater housings, as long as the seal itself stays within that range.
Is it safe near food or drinking water?
The manufacturer states the compound meets FDA 21 CFR 177.2600 and EC 1935/2004 for food contact, and it is a WRAS approved material. We can send the declaration if your audit needs it.
How accurate are the dimensions?
The profile is extruded to ISO 3302-1 class E2, the normal tolerance class for extruded rubber sections. Check your slot against the drawing before you order.
Will it flatten over time?
Its compression set is 31% after 22 hours at 175°C, a demanding hot test, so it keeps its recovery well through repeated heat cycles.
How do I cut and join it?
Cut it with a sharp knife or shears. Join it with a silicone adhesive or silicone sealant; most general-purpose glues and contact adhesives will not bond to silicone rubber.
Is every colour the same price?
Yes. All 7 colours cost £675.00 per 25m coil inc VAT (£27.00 per metre).
Complete your project
- Silicone T Seal Profile – 10mm x 8mm, 3mm leg (3.0mm head)
- Silicone T Seal Profile – 9mm x 8mm, barbed push-in leg
- Silicone T Seal Profile – 10mm x 14mm (taller, for bigger gaps)
Not sure it will fit? Send us a photo, or the width and depth of the slot, and we will check it for you. Contact our team.
Product details
| SKU | IP-SITS-10X8-L4-25M-BLK |
|---|---|
| Weight | 3.31 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone T Seal Profile – 10mm x 8mm, 4mm Leg (2.6mm Head) – 60 Shore A – 25m Coil