Rubber & FoamSKU IP-SITS-9X8-25M-BLK
Silicone T Seal Profile – 9mm x 8mm, Barbed Push-In Leg – 60 Shore A – 25m Coil
A wide-headed silicone T seal with a barbed push-in leg. The flat head is 9mm wide and 2.7mm thick, so it gives a broad, soft sealing face. Under the head, a short 2.16mm neck leads into a 4mm long barb that swells to about 3.7mm and then closes to a flat 2.16mm tip. Push the tip into a slot and the barb squeezes in and locks behind the slot walls. The profile is 8mm tall overall. It is made in a medium 60 Shore A silicone with low compression set, rated from -50°C to +180°C, in seven colours at one price. Each coil is one unbroken 25m length.
At a glance
- Head 9mm wide × 2.7mm thick, flat on both faces
- Barbed leg 5.3mm long below the head: 2.16mm neck, a 4mm barb about 3.7mm at its widest, and a flat 2.16mm tip
- 8mm overall height
- About 3.4mm of head each side of the leg, so the head covers both edges of the slot
- 60 Shore A silicone with a 31% compression set (22 h at 175°C): it springs back well after long clamping at heat
- Working range -50°C to +180°C
- The manufacturer states the compound meets FDA 21 CFR 177.2600 and EC 1935/2004 for food contact. It is a WRAS approved material.
- Black, white, translucent, red, green, blue or yellow, all at the same price
- Held in stock in every colour
Typical uses
- Oven, prover and dryer doors with a slot in the frame, up to +180°C
- Inspection hatches and covers on food, bakery and brewing equipment
- Heating enclosures, furnace panels and temperature-controlled ducting
- Control cabinet, enclosure and machine-guard doors
- Marine and outdoor hatches and window frames, where UV and ozone crack other rubbers
- Electronics bays and trim joints in vehicles and plant
- Colour-coded seals for hygiene zones (red, green, blue, yellow)
Technical drawing
![]()
Full specification
| Property | Value | Test method |
|---|---|---|
| Dimensions | ||
| Profile type | Solid T section: flat head, centred barbed leg | – |
| Overall height | 8 mm | – |
| Head width | 9 mm | – |
| Head thickness | 2.7 mm | – |
| Leg length below head | 5.3 mm (reference, 8 − 2.7) | – |
| Barb length (to tip) | 4 mm | – |
| Neck length | 1.3 mm (reference, 8 − 2.7 − 4) | – |
| Tip width (base thickness) | 2.16 mm, flat | – |
| Neck width | About 2.16 mm (scaled from the drawing) | – |
| Barb width at widest point | About 3.7 mm (scaled from the drawing) | – |
| Head overhang each side | About 3.4 mm (reference, leg centred) | – |
| Suits slot (our guidance) | Approx. 2.5–3.0 mm wide, at least 6 mm deep | – |
| Dimensional tolerance | Class E2 | ISO 3302-1:2014 |
| Length per coil | 25 m, one continuous length | – |
| Material and physical properties | ||
| Compound | Solid silicone rubber | – |
| Hardness | 60 Shore A | DIN ISO 48-4 |
| Density | 1.15 g/cm³ | DIN EN ISO 1183-1, method A |
| Tensile strength | 11 N/mm² (11 MPa) | ISO 37, type 1 |
| Elongation at break | 550 % | ISO 37, type 1 |
| Tear strength | 26 N/mm (26 kN/m) | ASTM D624, die B |
| Compression set | 31 % after 22 h at 175 °C | DIN ISO 815-1, type B, method A |
| Rebound resilience | 59 % | ISO 4662 |
| Service conditions | ||
| Working temperature | -50 °C to +180 °C | – |
| Environmental resistance | Ozone, UV, oxidation, weathering, corona discharge, cosmic and ionising radiation | – |
| Supply | ||
| Colours | Black, white, translucent, red, green, blue, yellow | – |
| Approx. weight (calculated from the ≈39 mm² section and the density) | About 45 g per metre, 1.1 kg per coil | – |
| Unit of sale | 1 coil of 25 m (£27.00 per metre inc VAT) | – |
| Our part numbers | IP-SITS-9X8-25M-<colour> (BLK, WHT, TRN, RED, GRN, BLU, YEL) | – |
Materials and compliance
These are the claims the manufacturer makes in writing for this profile. Ask us if your file needs the certificate or declaration.
| Claim | What it means for you |
|---|---|
| FDA 21 CFR 177.2600 | The compound meets the US rule for rubber articles in repeated contact with food. |
| EC 1935/2004 | The compound meets the EU framework regulation for materials that come into contact with food. |
| WRAS approved material | The material is accepted for contact with drinking water in UK water fittings. |
| Free from TSE/BSE by-products | No animal-derived ingredients that carry TSE/BSE risk. |
| Phthalate free | Made without phthalate plasticisers. |
The approvals cover the material as supplied. Whether your finished assembly complies also depends on its design, its cleaning regime and the other materials in it, so check it against your own requirements.
Will it fit my slot?
Measure the slot's width and depth. The barb is about 3.7mm at its widest, so it needs a slot narrower than that to grip: about 2.5–3.0mm suits it. The tip and neck are 2.16mm, so the leg starts easily and the barb squeezes in behind. The slot should be at least 6mm deep, so the 5.3mm leg goes fully in and the head sits flat on the surface. In a slot narrower than about 2.2mm the barb will be hard to push home; in one wider than about 3.3mm it will not grip, so choose a different T seal. These slot sizes are our guidance from the geometry, not a manufacturer figure, so try a short length first.
Why 60 Shore A?
60 Shore A is a medium silicone, about as firm as a car tyre tread. It is soft enough for the 2.7mm thick head to compress and close a gap, and firm enough for the barb to hold in its slot. Its compression set is low: 31% after 22 hours at 175°C. That means it recovers well when a door clamps on it at heat for long periods, which suits oven and prover doors.
How much do I need?
Add up the length of every slot and allow about 5% for trimming and joints. For example, a 600mm × 400mm door needs 2.0m, or about 2.1m with the allowance, so one 25m coil seals 11 doors of that size.
Fitting tips
- Clear any old seal, grease and grit out of the slot, and let it dry
- Start partway along a straight side, not at a corner
- Line the flat tip up with the slot and press the head down with your thumb or a small plastic roller as you go, until the barb clicks home and the head sits flat. A drop of soapy water helps it slide in.
- At tight corners, cut a small V-notch out of the head so it lies flat
- Cut the end slightly long with a sharp knife and push the ends together; a dab of silicone adhesive keeps the joint closed
FAQ: frequently asked questions
What slot does it fit?
A slot about 2.5–3.0mm wide and at least 6mm deep (our guidance). The head is 9mm wide, so it overlaps the slot by about 3mm each side and hides the edges.
Which way up does it go?
The barbed leg goes into the slot, flat tip first. The flat 9mm head sits on the surface and faces the door, lid or panel it seals against.
How far does it stand proud?
2.7mm, the thickness of the head. Set the door so it compresses the head by about a quarter to a third of that, roughly 0.7–0.9mm.
Can I fit it without a slot?
The barbed leg is made to lock in a slot. On a flat surface, choose a self-adhesive or flat strip seal instead, or ask us.
Can it be used on ovens and heaters?
Yes. It is rated to +180°C continuous and stays flexible down to -50°C. Its low compression set means it keeps sealing on doors that clamp shut at heat.
Is it safe near food or drinking water?
The manufacturer states the compound meets FDA 21 CFR 177.2600 and EC 1935/2004 for food contact, and it is a WRAS approved material. We can send the declaration if your audit needs it.
How accurate are the dimensions?
The profile is extruded to ISO 3302-1 class E2, the normal tolerance class for extruded rubber sections. Check your slot against the drawing before you order.
How do I cut and join it?
Cut it with a sharp knife or shears. To join it, use a silicone adhesive or silicone sealant. Most general-purpose glues and contact adhesives will not bond to silicone rubber.
Is every colour the same price?
Yes. All 7 colours cost £675.00 per 25m coil inc VAT (£27.00 per metre).
Complete your project
- Silicone T Seal Profile – 9mm x 14mm (same head width, longer leg)
- Silicone T Seal Profile – 7mm x 9mm (narrower head, 60 Shore A)
- Silicone T Seal Profile – 5mm x 9mm (slim head, 60 Shore A)
Not sure it will fit? Send us a photo, or the width and depth of the slot, and we will check it for you. Contact our team.
Product details
| SKU | IP-SITS-9X8-25M-BLK |
|---|---|
| Weight | 2.65 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone T Seal Profile – 9mm x 8mm, Barbed Push-In Leg – 60 Shore A – 25m Coil