Rubber & FoamSKU IP-SITS-6X4.5-25M-BLK
Silicone T Seal Profile – 6mm x 4.5mm – 25m Coil
A firm, low-profile push-fit seal with the widest flat face in this height. This silicone T seal profile is a solid 6mm x 4.5mm extrusion with a square-edged flat head (6mm wide, 2.5mm deep) on a 2mm wide leg. Press the leg into a narrow slot and the head stands 2.5mm proud, giving the closing door, lid or panel a full 6mm contact band, while the shoulders cover a generous 2mm of frame either side. At 80 Shore A it is a hard-wearing silicone that keeps its square edges and resists being pulled out of the slot. Supplied as one continuous 25m coil in seven colours.
£675.00 inc VAT per 25m coil, which is £27.00 per metre.
At a glance
- Flat head 6mm wide and 2.5mm deep, square edges, 2mm shoulder each side of the leg
- Leg 2mm wide and 2mm long: a push fit in a slot about 1.8–2.0mm wide and at least 2mm deep
- Overall height only 4.5mm, for low-clearance frames; the head stands 2.5mm proud before compression
- Firm solid silicone, 80 Shore A, with 440% elongation and 54% rebound
- Works from -50°C to +180°C without hardening or going brittle
- Food-contact compound (FDA 21 CFR 177.2600 and EC 1935/2004) and WRAS approved material
- 25m coil in black, white, translucent, red, green, blue or yellow, all the same price
Typical uses
- Lids, guards and inspection hatches on food processing, packaging and brewing equipment
- Oven, warming cabinet and drying room doors with a narrow 2mm seal slot
- HVAC access panels, duct inspection doors and heated enclosures
- Thin glazing and infill panels in aluminium or stainless frames, where the wider head hides the slot edge
- Hatch, window and trim seals on marine and vehicle bodywork
- Colour-coded seals for hygiene zones (blue, green, yellow, red)
Technical drawing
![]()
Full specification
| Property | Value | Test method |
|---|---|---|
| Dimensions | ||
| Profile type | Solid T section, flat square-edged head, straight leg | – |
| Overall width (head) | 6.0 mm | – |
| Overall height | 4.5 mm | – |
| Head depth | 2.5 mm | – |
| Leg (base) width | 2.0 mm | – |
| Leg length below head | 2.0 mm (reference, 4.5 − 2.5) | – |
| Shoulder overhang each side | 2.0 mm (reference, (6.0 − 2.0) ÷ 2) | – |
| Suggested slot | About 1.8–2.0 mm wide, at least 2.0 mm deep | Guidance |
| Dimensional tolerance | Class E2 | ISO 3302-1:2014 |
| Length per coil | 25 m, one continuous length | – |
| Material and physical properties | ||
| Material | Solid silicone rubber | – |
| Hardness | 80 Shore A | DIN ISO 48-4 |
| Density | 1.20 g/cm³ | DIN EN ISO 1183-1 A |
| Tensile strength | 10 N/mm² (10 MPa) | ISO 37 Type 1 |
| Elongation at break | 440 % | ISO 37 Type 1 |
| Tear strength | 28 N/mm | ASTM D624 B |
| Compression set | 78 % after 22 h at 175 °C | DIN ISO 815-1 Type B, Method A |
| Rebound resilience | 54 % | ISO 4662 |
| Service conditions | ||
| Working temperature | -50 °C to +180 °C | – |
| Environmental resistance | Ozone, UV, oxidation, weathering, corona discharge, cosmic and ionising radiation | – |
| Supply | ||
| Colours | Black, white, translucent, red, green, blue, yellow (same profile and price) | – |
| Unit of sale | 1 coil of 25 m (£27.00 per metre) | – |
Materials and compliance claims
These are the claims the manufacturer states for this exact profile and compound. Ask us for the certificate or declaration you need for your technical file.
| Claim | What it means for you |
|---|---|
| FDA 21 CFR 177.2600 | The compound meets the US rule for rubber articles intended for repeated contact with food. |
| EC 1935/2004 | The compound meets the EU framework regulation for materials intended to come into contact with food. |
| WRAS approved material | The material is listed as suitable for contact with drinking water in UK water fittings. |
| Free from TSE/BSE by-products | No animal-derived ingredients that carry TSE/BSE risk. |
| Phthalate free | Made without phthalate plasticisers. |
Approvals apply to the material as supplied. Whether a finished assembly complies also depends on your design, cleaning regime and other materials, so check against your own requirements.
Will it fit my groove?
This profile is made for a narrow, straight-sided slot about 1.8–2.0mm wide and at least 2mm deep. The compound is firm (80 Shore A), so it will not squash into a slot much narrower than 1.8mm. A slot the same width as the 2mm leg or slightly wider will still hold, but add a thin bead of silicone adhesive along the bottom. The 6mm head overhangs the slot by 2mm on each side, so the frame needs at least that much flat land either side of the slot for the shoulders to sit on.
![]()
How much do I need?
Measure every slot and add about 5% for trimming and joints. Example: a cabinet door with a 600mm x 450mm groove needs 2.1m, so one 25m coil does about 11 doors with allowance.
Fitting tips
- Clean old seal and debris out of the slot and let it dry
- Start in the middle of a long side, not at a corner
- Press the leg in with your thumb or a plastic roller until the shoulders sit flat on the frame; a firm 80 Shore A seal may need a light tap with a rubber mallet
- Do not stretch the seal as you go: stretched silicone shrinks back and opens gaps at the joints
- Cut slightly long with a sharp knife or shears and push the ends together for a tight butt joint; a dab of silicone adhesive keeps it closed
FAQ: frequently asked questions
Which way up does it go?
The 2mm leg goes into the slot. The flat 6mm face of the head faces outwards, towards the door, lid or panel that closes onto it.
How big a gap does it close?
The head stands 2.5mm proud of the frame. A firm 80 Shore A seal needs more closing force per millimetre of squeeze than a soft one, so as a guide design for about 15–25% squeeze of the head: a closed gap of roughly 1.9–2.1mm between the frame and the closing face. For a larger or uneven gap, a softer or taller profile will do it with less force.
What slot size do I need?
A straight slot about 1.8–2.0mm wide and at least 2mm deep, with at least 2mm of flat frame either side. Check your slot against the drawing before ordering, or send us the dimensions and we will check it.
How is it different from the 5.5mm x 4.5mm T seal?
Same compound, same 2mm leg and same 4.5mm height. The head is 0.5mm wider (6mm instead of 5.5mm), so each shoulder covers 2mm of frame instead of 1.75mm. Choose this one for a wider contact band or to hide a slightly chipped slot edge.
Why choose a hard 80 Shore A seal?
Harder silicone keeps its square edges, resists cuts, scuffs and being pulled from the slot, and gives a crisp, flat finish line. The trade-off is a higher closing force and a compression set of 78% after 22 hours at 175°C, so under sustained heat and squeeze it will take on a permanent set. For doors that are opened and closed at high temperature all day, a softer, lower-set grade may last longer; ask us if you are unsure.
Will it survive heat?
It is rated from -50°C to +180°C, so it suits ovens, warming cabinets, dryers and machinery that runs hot, as well as cold stores.
Is it safe near food or drinking water?
Yes. The compound is stated to meet FDA 21 CFR 177.2600 and EC 1935/2004 for food contact, and it is a WRAS approved material. Ask for the certificate if your audit needs it.
How do I cut and join it?
Cut square with a sharp knife or shears. Butt the ends together and bond with a silicone adhesive. Because the compound is firm, mitre and bond the corners rather than bending the seal round a tight corner.
How tight are the dimensions?
The profile is extruded to ISO 3302-1 class E2, a standard tolerance class for extruded rubber.
Can I order a shorter length or a different colour mix?
This listing is a full 25m coil in one colour. For cut lengths, mixed colours or larger quantities, contact us for a quote.
Complete your project
- Silicone T Seal Profile – 5.5mm x 4.5mm (same height and compound, 5.5mm head)
- Silicone T Seal Profile – 4.3mm x 4.5mm (same height, narrower head)
- Silicone T Seal Profile – 5mm x 5.9mm (80 Shore A, deeper 3mm leg)
Not sure this profile matches your slot? Send us a photo or the slot dimensions and we will check it. Contact our team.
Product details
| SKU | IP-SITS-6X4.5-25M-BLK |
|---|---|
| Weight | 2.2 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone T Seal Profile – 6mm x 4.5mm – 25m Coil