Rubber & FoamSKU IP-SITS-7.4X16.6-25M-BLK
Silicone T Seal Profile – 7.4mm x 16.6mm, Ribbed Head, Tapered Leg – 80 Shore A – 25m Coil
A firm silicone T seal with a deep, tapered push-in leg. The flat head is 7.4mm wide and 1.5mm thick, with a narrow 1.5mm rib running along the centre of its face. Under the head, a 14.3mm long leg starts 2.0mm wide and tapers to a rounded tip, so it drives easily into a narrow slot and wedges tight as it goes down. The profile is 16.6mm tall overall. It is made in a hard 80 Shore A silicone, rated from -50°C to +180°C, in seven colours at one price. Each coil is one unbroken 25m length.
At a glance
- Head 7.4mm wide × 1.5mm thick, with a 1.5mm wide centre rib on its face
- Leg 14.3mm long: 2.0mm wide under the head, tapering to a 0.8mm rounded tip (R0.4)
- 16.6mm overall, from the top of the rib to the tip of the leg
- 2.7mm shoulder each side of the leg, so the head covers both edges of the slot
- Hard 80 Shore A silicone: holds a straight line and will not roll in the slot
- Working range -50°C to +180°C
- The manufacturer states the compound meets FDA 21 CFR 177.2600 and EC 1935/2004 for food contact. It is a WRAS approved material.
- Black, white, translucent, red, green, blue or yellow, all at the same price
- Held in stock in every colour
Typical uses
- Narrow saw-cut or routed slots in oven, prover and dryer door frames up to +180°C
- Cover and splash strips on food, bakery and packaging machinery
- Control cabinet, enclosure and machine-guard doors with a thin seal groove
- Air handling units and ductwork access panels
- Panel joints and infill strips where a slim, neat line of seal is wanted
- Outdoor and marine enclosures, where UV and ozone crack other rubbers
- Colour-coded seals for hygiene zones (red, green, blue, yellow)
Technical drawing
![]()
Full specification
| Property | Value | Test method |
|---|---|---|
| Dimensions | ||
| Profile type | Solid T section: flat head with a centre rib, centred tapered leg | – |
| Overall height | 16.6 mm (rib top to leg tip) | – |
| Head width | 7.4 mm | – |
| Head thickness | 1.5 mm | – |
| Centre rib width | 1.5 mm | – |
| Centre rib height | 0.8 mm (reference, 16.6 − 1.5 − 14.3) | – |
| Leg length below head | 14.3 mm | – |
| Leg width under head (base thickness) | 2.0 mm | – |
| Leg tip | R0.4 mm round (0.8 mm wide) | – |
| Shoulder each side | 2.7 mm (reference, leg centred) | – |
| Suits slot (our guidance) | Approx. 1.5–2.0 mm wide, at least 15 mm deep | – |
| Dimensional tolerance | Class E2 | ISO 3302-1:2014 |
| Length per coil | 25 m, one continuous length | – |
| Material and physical properties | ||
| Compound | Solid silicone rubber | – |
| Hardness | 80 Shore A | DIN ISO 48-4 |
| Density | 1.20 g/cm³ | DIN EN ISO 1183-1, method A |
| Tensile strength | 10 N/mm² (10 MPa) | ISO 37, type 1 |
| Elongation at break | 440 % | ISO 37, type 1 |
| Tear strength | 28 N/mm (28 kN/m) | ASTM D624, die B |
| Compression set | 78 % after 22 h at 175 °C | DIN ISO 815-1, type B, method A |
| Rebound resilience | 54 % | ISO 4662 |
| Service conditions | ||
| Working temperature | -50 °C to +180 °C | – |
| Environmental resistance | Ozone, UV, oxidation, weathering, corona discharge, cosmic and ionising radiation | – |
| Supply | ||
| Colours | Black, white, translucent, red, green, blue, yellow | – |
| Approx. weight (calculated from the 32 mm² section and the density) | About 38 g per metre, 0.96 kg per coil | – |
| Unit of sale | 1 coil of 25 m (£27.00 per metre inc VAT) | – |
| Our part numbers | IP-SITS-7.4X16.6-25M-<colour> (BLK, WHT, TRN, RED, GRN, BLU, YEL) | – |
Materials and compliance
These are the claims the manufacturer makes in writing for this profile. Ask us if your file needs the certificate or declaration.
| Claim | What it means for you |
|---|---|
| FDA 21 CFR 177.2600 | The compound meets the US rule for rubber articles in repeated contact with food. |
| EC 1935/2004 | The compound meets the EU framework regulation for materials that come into contact with food. |
| WRAS approved material | The material is accepted for contact with drinking water in UK water fittings. |
| Free from TSE/BSE by-products | No animal-derived ingredients that carry TSE/BSE risk. |
| Phthalate free | Made without phthalate plasticisers. |
The approvals cover the material as supplied. Whether your finished assembly complies also depends on its design, its cleaning regime and the other materials in it, so check it against your own requirements.
Will it fit my slot?
Measure the slot's width and depth. The leg is 2.0mm wide under the head and narrows steadily to 0.8mm at the tip, so it suits a narrow slot of about 1.5–2.0mm. In a 1.6mm slot the top few millimetres of the leg are squeezed, and that wedge is what holds the seal. The slot should be at least 15mm deep so the head can sit down flat. If your slot is shallower, trim the leg tip with a sharp knife, or choose a T seal with a shorter leg. If the slot is wider than 2.0mm, the leg will be loose: pick a T seal with a thicker leg.
Hard or soft: is 80 Shore A right for me?
80 Shore A is the firm end of silicone, close to a shoe heel. It holds a straight edge, resists scuffing and will not roll in the slot. That suits cover strips and doors that close lightly onto the seal, where the rib takes the contact. It is not the best choice where a door clamps hard on the seal for long periods at high heat. Its compression set of 78% (22 h at 175°C) means it takes a permanent set under that kind of load. For hard-clamped oven doors, a softer 50–60 Shore A T seal will spring back better. Ask us if you are not sure.
How much do I need?
Add up the length of every slot and allow about 5% for trimming and joints. For example, a 600mm × 400mm door needs 2.0m, or about 2.1m with the allowance, so one 25m coil seals 11 doors of that size.
Fitting tips
- Clear any old seal, grease and grit out of the slot, and let it dry
- Start partway along a straight side, not at a corner
- Feed the tip into the slot and press the head down with your thumb or a small plastic roller as you go. A drop of soapy water helps the leg slide down to full depth.
- At tight corners, cut a small V-notch out of the head so it lies flat. The hard compound will not bend round a sharp corner on its own.
- Cut the end slightly long with a sharp knife and push the ends together; a dab of silicone adhesive keeps the joint closed
FAQ: frequently asked questions
What slot does it fit?
A narrow slot about 1.5–2.0mm wide and at least 15mm deep. The head is 7.4mm wide, so it overlaps the slot by about 2.7mm each side and hides the edges.
Which way up does it go?
The long tapered leg goes into the slot, tip first. The flat head sits on the surface, with the centre rib facing the door, lid or panel it seals against.
What is the rib on the head for?
The 1.5mm wide, 0.8mm high rib is the first part to touch the closing door. It concentrates the contact on a narrow line, so a firm 80 Shore A seal still closes a gap without needing much door pressure.
How far does it stand proud?
2.3mm in total: 1.5mm of head plus the 0.8mm rib. Set your door so it just compresses the rib and head; this is a light-contact seal, not a deep-squash gasket.
Can it be used on ovens and heaters?
It is rated to +180°C continuous and stays flexible down to -50°C. It suits oven, prover and dryer panels and lightly loaded doors. For doors clamped hard onto the seal at high heat, a softer grade recovers better (see "Hard or soft" above).
Is it safe near food or drinking water?
The manufacturer states the compound meets FDA 21 CFR 177.2600 and EC 1935/2004 for food contact, and it is a WRAS approved material. We can send the declaration if your audit needs it.
How accurate are the dimensions?
The profile is extruded to ISO 3302-1 class E2, the normal tolerance class for extruded rubber sections. Check your slot against the drawing before you order.
How do I cut and join it?
Cut it with a sharp knife or shears; the firm compound cuts cleanly. To join it, use a silicone adhesive or silicone sealant. Most general-purpose glues and contact adhesives will not bond to silicone rubber.
Is every colour the same price?
Yes. All 7 colours cost £675.00 per 25m coil inc VAT (£27.00 per metre).
Complete your project
- Silicone T Seal Profile – 6mm x 12mm (tapered leg, softer 60 Shore A)
- Silicone T Seal Profile – 6.7mm x 9mm (same 80 Shore A compound, thicker 3mm leg)
- Silicone T Seal Profile – 7mm x 10mm (similar head width, soft 50 Shore A)
Not sure it will fit? Send us a photo, or the width and depth of the slot, and we will check it for you. Contact our team.
Product details
| SKU | IP-SITS-7.4X16.6-25M-BLK |
|---|---|
| Weight | 2.2 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone T Seal Profile – 7.4mm x 16.6mm, Ribbed Head, Tapered Leg – 80 Shore A – 25m Coil