Rubber & FoamSKU IP-SITS-6.7X9-25M-BLK
Silicone T Seal Profile – 6.7mm x 9mm – 80 Shore A – 25m Coil
A solid, firm silicone T seal with a flat head 6.7mm wide and 3mm thick, on a 3mm wide leg. It is 9mm tall overall. The leg pushes 6mm deep into a slot about 2.8–3.0mm wide and holds the seal in place. The head sits flat on the surface and closes the gap against dust, splash, draughts and heat. It is made in a hard 80 Shore A silicone, so it keeps its shape. That makes it a good choice for wiper, cover and edge strips that take knocks, and for doors where the seal must not roll or squash flat. It comes in seven colours, all at the same price. Each coil is one unbroken 25m length.
At a glance
- Head 6.7mm wide × 3.0mm thick; leg 3.0mm wide; 9.0mm overall height (6.0mm of leg below the head)
- 1.85mm shoulder each side of the leg, so the head covers both edges of the slot
- Hard 80 Shore A silicone: stiff, hard-wearing and holds a crisp edge
- Working range -50°C to +180°C
- The manufacturer states the compound meets FDA 21 CFR 177.2600 and EC 1935/2004 for food contact. It is a WRAS approved material.
- Black, white, translucent, red, green, blue or yellow, all at the same price
- Held in stock in every colour
Typical uses
- Slot seals and cover strips in machine guards, enclosures and aluminium profile frames
- Wiper and splash strips on food, bakery and packaging machinery
- Edge seals on oven, prover and dryer panels up to +180°C
- Air handling units, fan coil housings and ductwork access panels
- Infill strips for open T-slots, to keep swarf and dirt out
- Outdoor enclosures and marine hatches, where UV and ozone crack other rubbers
- Colour-coded seals for hygiene zones (red, green, blue, yellow)
Technical drawing
![]()
Full specification
| Property | Value | Test method |
|---|---|---|
| Dimensions | ||
| Profile type | Solid T section, square-cut flat head, centred leg | – |
| Overall height | 9.0 mm | – |
| Head width | 6.7 mm | – |
| Head thickness | 3.0 mm | – |
| Leg width (base thickness) | 3.0 mm | – |
| Leg length below head | 6.0 mm (reference, 9.0 − 3.0) | – |
| Shoulder each side | 1.85 mm (reference, leg centred) | – |
| Suits slot | Approx. 2.8–3.0 mm wide, at least 6.0 mm deep | – |
| Dimensional tolerance | Class E2 | ISO 3302-1:2014 |
| Length per coil | 25 m, one continuous length | – |
| Material and physical properties | ||
| Compound | Solid silicone rubber | – |
| Hardness | 80 Shore A | DIN ISO 48-4 |
| Density | 1.20 g/cm³ | DIN EN ISO 1183-1, method A |
| Tensile strength | 10 N/mm² (10 MPa) | ISO 37, type 1 |
| Elongation at break | 440 % | ISO 37, type 1 |
| Tear strength | 28 N/mm (28 kN/m) | ASTM D624, die B |
| Compression set | 78 % after 22 h at 175 °C | DIN ISO 815-1, type B, method A |
| Rebound resilience | 54 % | ISO 4662 |
| Service conditions | ||
| Working temperature | -50 °C to +180 °C | – |
| Environmental resistance | Ozone, UV, oxidation, weathering, corona discharge, cosmic and ionising radiation | – |
| Supply | ||
| Colours | Black, white, translucent, red, green, blue, yellow | – |
| Approx. weight (calculated from the 38.1 mm² section and the density) | About 46 g per metre, 1.15 kg per coil | – |
| Unit of sale | 1 coil of 25 m (£27.00 per metre inc VAT) | – |
| Our part numbers | IP-SITS-6.7X9-25M-<colour> (BLK, WHT, TRN, RED, GRN, BLU, YEL) | – |
Materials and compliance
These are the claims the manufacturer makes in writing for this profile. Ask us if your file needs the certificate or declaration.
| Claim | What it means for you |
|---|---|
| FDA 21 CFR 177.2600 | The compound meets the US rule for rubber articles in repeated contact with food. |
| EC 1935/2004 | The compound meets the EU framework regulation for materials that come into contact with food. |
| WRAS approved material | The material is accepted for contact with drinking water in UK water fittings. |
| Free from TSE/BSE by-products | No animal-derived ingredients that carry TSE/BSE risk. |
| Phthalate free | Made without phthalate plasticisers. |
The approvals cover the material as supplied. Whether your finished assembly complies also depends on its design, its cleaning regime and the other materials in it, so check it against your own requirements.
Will it fit my slot?
Measure the slot's width and depth. The leg is 3.0mm wide, so it grips best in a slot of about 2.8–3.0mm. The slot should be at least 6.0mm deep so the head can sit down flat; a deeper slot is fine. Because 80 Shore A is firm, the leg will not squeeze into a slot much narrower than 2.8mm. If your slot is 2.5mm or less, choose a softer T seal or one with a thinner leg.
Hard or soft: is 80 Shore A right for me?
80 Shore A is the firm end of silicone, close to a shoe heel. It resists scuffing, holds a straight edge and will not roll in the slot, so it suits wiper strips, cover strips and doors that are only closed lightly onto the seal. It is not the best choice where a door clamps hard on the seal for long periods at high heat. Its compression set of 78% (22 h at 175°C) means it takes a permanent set under that kind of load. For hard-clamped oven doors, a softer 50–60 Shore A T seal will spring back better. Ask us if you are not sure.
How much do I need?
Add up the length of every slot and allow about 5% for trimming and joints. For example, a 600mm × 400mm guard door needs 2.0m, or about 2.1m with the allowance, so one 25m coil seals 11 doors of that size.
Fitting tips
- Clear any old seal, grease and grit out of the slot, and let it dry
- Start partway along a straight side, not at a corner
- Press the leg in with your thumb or a small plastic roller as you go. A drop of soapy water helps the firm leg slide down to full depth.
- At tight corners, cut a small V-notch out of the head so it lies flat. The hard compound will not bend round a sharp corner on its own.
- Cut the end slightly long with a sharp knife and push the ends together; a dab of silicone adhesive keeps the joint closed
FAQ: frequently asked questions
What slot does it fit?
A slot about 2.8–3.0mm wide and at least 6.0mm deep. The head is 6.7mm wide, so it overlaps the slot by 1.85mm each side and covers the edges.
Which way up does it go?
The 3mm leg goes into the slot, and the wider, flat head sits on the surface, facing the door, lid or panel it seals against.
How far does the head stand proud?
3mm. The hard 80 Shore A silicone compresses only a little, so it works best as a light-contact seal, wiper or cover strip, not as a deep-squash door gasket.
Can it be used near ovens and heaters?
It is rated to +180°C continuous and stays flexible down to -50°C. It suits panels, wipers and lightly loaded doors on ovens, dryers and heater housings. For doors clamped hard onto the seal at high heat, a softer grade recovers better (see "Hard or soft" above).
Is it safe near food or drinking water?
The manufacturer states the compound meets FDA 21 CFR 177.2600 and EC 1935/2004 for food contact, and it is a WRAS approved material. We can send the declaration if your audit needs it.
How accurate are the dimensions?
The profile is extruded to ISO 3302-1 class E2, the normal tolerance class for extruded rubber sections. Check your slot against the drawing before you order.
How do I cut and join it?
Cut it with a sharp knife or shears; the firm compound cuts cleanly. To join it, use a silicone adhesive or silicone sealant. Most general-purpose glues and contact adhesives will not bond to silicone rubber.
Is every colour the same price?
Yes. All 7 colours cost £675.00 per 25m coil inc VAT (£27.00 per metre).
Complete your project
- Silicone T Seal Profile – 6mm x 9.5mm (similar size in a softer 60 Shore A)
- Silicone T Seal Profile – 5mm x 9mm (narrower 5mm head, soft 50 Shore A)
- Silicone T Seal Profile – 9mm x 14mm (wider head, deeper slot)
Not sure it will fit? Send us a photo, or the width and depth of the slot, and we will check it for you. Contact our team.
Product details
| SKU | IP-SITS-6.7X9-25M-BLK |
|---|---|
| Weight | 2.65 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone T Seal Profile – 6.7mm x 9mm – 80 Shore A – 25m Coil