Rubber & FoamSKU IP-SILT-9X14-BLACK
Silicone T Seal Profile – 9mm x 14mm, 6mm Head, 5mm Leg – 40 Shore A – 25m Coil
A solid silicone T seal with a chunky 9mm wide x 6mm thick head on a 5mm wide square leg, 14mm high overall. Push the leg into a slot or the gap between two panels and the head covers the joint with a soft, deep cushion that a door, lid or cover closes onto. It is a soft 40 Shore A food-contact silicone (FDA 21 CFR 177.2600, EC 1935/2004, WRAS) that works from -50°C to +180°C, sold as one continuous 25m coil in seven colours.
At a glance
- Profile: solid T section, head 9mm x 6mm, leg 5mm wide x 8mm long, 14mm overall
- Fits: a slot or panel gap about 4.5–5mm wide and 8–9mm deep (our guidance; test a short length first)
- Material: soft 40 Shore A silicone, low 36% compression set at 175°C
- Temperature: -50°C to +180°C continuous working range
- Food and water contact: FDA 21 CFR 177.2600, EC 1935/2004 and WRAS approved
- Colours: black, white, translucent, red, green, blue or yellow (same price)
- Supplied: one 25m coil, £27.00 per metre inc VAT, held in stock
Technical drawing
![]()
Dimensions in mm. The leg is centred, leaving a 2mm shoulder each side. Extrusion tolerance ISO 3302-1:2014 class E2.
Specifications
| Property | Value | Test method |
|---|---|---|
| Profile type | Solid T section (head + square leg) | – |
| Head width | 9 mm | Nominal |
| Head thickness | 6 mm | Nominal |
| Leg width (supplier "base thickness") | 5 mm | Nominal |
| Leg length below head | 8 mm (14 − 6) | Derived |
| Overall height | 14 mm | Nominal |
| Shoulder each side of leg | 2 mm ((9 − 5) ÷ 2) | Derived |
| Suggested slot (our guidance) | ≈ 4.5–5 mm wide, ≥ 8–9 mm deep | Fitting guidance, not a supplier figure |
| Dimensional tolerance | Class E2 | ISO 3302-1:2014 |
| Coil length | 25 m continuous | – |
| Material | Silicone rubber | – |
| Hardness | 40 Shore A (± 5 typical) | DIN ISO 48-4 |
| Density | 1.12 g/cm³ | DIN EN ISO 1183-1 A |
| Tensile strength | 9.6 N/mm² (MPa) | ISO 37 Type 1 |
| Elongation at break | 770 % | ISO 37 Type 1 |
| Tear strength | 28 N/mm | ASTM D 624 B |
| Compression set (22 h at 175°C) | 36 % | DIN ISO 815-1 Type B, Method A |
| Rebound resilience | 56 % | ISO 4662 |
| Working temperature | -50°C to +180°C | – |
| Environmental resistance | Ozone, UV, oxidation, weathering, corona discharge, cosmic and ionising radiation | – |
| Colours | Black, white, translucent, red, green, blue, yellow | – |
| Approx. weight | ≈ 105 g per metre, ≈ 2.6 kg per 25 m coil | Calculated from section area × density |
The "± 5" hardness band is typical for silicone compounds, not tested on this profile. All other values are for this product.
Materials and compliance
- FDA 21 CFR 177.2600: compliant rubber for repeated contact with food.
- EC 1935/2004: meets the EU framework regulation for food-contact materials.
- WRAS approved: approved material for contact with drinking water.
- Free from TSE/BSE by-products and free from phthalates.
Silicone is naturally resistant to ozone, UV and weathering, so the seal stays flexible outdoors and in hot, steamy plant rooms without cracking.
Typical uses
- Door and hatch seals on food processing equipment, ovens, proving cabinets and hot cupboards
- Colour-coded seals for food hygiene zones (blue, red, green, yellow, white)
- Joint seals between panels on HVAC ducting, heated enclosures and furnace casings
- Weather and splash seals on marine hatches, windows and structural joints
- Covers for the slot in aluminium framing and enclosure lids
Which silicone T seal do I need?
| Profile | Head | Leg | Best for |
|---|---|---|---|
| 9mm x 14mm (this item) | 9 x 6mm | 5mm solid, 40 ShA | Soft, deep head; 4.5–5mm slots |
| 9mm x 8mm | 9 x 2.7mm | Barbed, 60 ShA | Thin head; narrow 2.5–3mm slots |
| 10mm x 14mm | 10mm | – | Slightly wider head, same height |
| 10mm x 13mm | 10mm | – | Slightly shallower slot |
| 11mm x 11.4mm | 11mm | – | Wider joints |
| 25mm x 25mm | 25mm | – | Wide joints and deep slots |
How to fit
- Clean the slot and let it dry. Remove burrs or old sealant.
- Measure the run and cut the coil square with a sharp knife or shears; add 1–2mm per butt joint so the ends meet under light pressure.
- For a permanent fix, run a bead of silicone adhesive into the slot first.
- Start at one end and press the 5mm leg fully home along the run, working in short sections without stretching the seal.
- Smooth the head down so both 2mm shoulders sit flat on the face, then close the door or lid to check the contact line.
How much do I need?
Add up the perimeter of every opening and allow a little for trimming. Example: an oven door 600mm x 450mm needs 2 x (0.60 + 0.45) = 2.1m, so one 25m coil seals about eleven doors of that size.
Frequently asked questions
What size slot does the 9mm x 14mm T seal fit?
The leg is 5mm wide and 8mm long. Our guidance is a slot about 4.5–5mm wide and at least 8–9mm deep. A slot slightly narrower than 5mm gives a grip fit in this soft 40 Shore A silicone; in a wider slot use silicone adhesive. Try a short offcut in your slot before fitting a full run.
How does it seal?
The 9mm x 6mm head stands proud of the face. The door, lid or panel closes onto it and compresses the soft head, which seals the gap and covers 2mm of face either side of the slot.
Is it safe for food and drinking water?
Yes. The supplier states this compound complies with FDA 21 CFR 177.2600 and EC 1935/2004 and is WRAS approved. It is free from TSE/BSE by-products and phthalates.
What temperatures can it take?
-50°C to +180°C continuously, so it suits ovens, proving cabinets, hot cupboards, heated enclosures and freezers. Compression set is only 36% after 22 hours at 175°C, so it keeps its shape at temperature.
How do I cut and join it?
Cut square with a sharp blade or shears. Butt joints can be bonded with a silicone adhesive or RTV sealant; at corners, either mitre-cut the head and bond it, or ease the seal round the corner with a radius of a few centimetres.
Can I use it outdoors?
Yes. Silicone resists UV, ozone and weathering and stays flexible from -50°C, so it suits marine hatches, windows and outdoor enclosures.
Do all colours cost the same?
Yes. Black, white, translucent, red, green, blue and yellow are all £675.00 inc VAT per 25m coil (£27.00 per metre). Blue, red, green, yellow and white are popular for food-zone colour coding.
Can I buy a shorter length?
This listing is for a full 25m coil. For shorter lengths or larger quantities, contact our team on +44 1282 277786 or sales@industrial-polymers.co.uk.
Not sure it's the right profile? Send us a photo or sketch of your slot and our team will check the fit.
Product details
| SKU | IP-SILT-9X14-BLACK |
|---|---|
| Weight | 5.95 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone T Seal Profile – 9mm x 14mm, 6mm Head, 5mm Leg – 40 Shore A – 25m Coil