
Rubber & FoamSKU IP-TPEU-8X13-STD
TPE U Channel Edge Trim – 8mm x 13mm for 2mm Panels – 50m Coil
A black TPE teardrop U channel that pushes onto 2mm sheet and stays there without glue. The slot is 1mm wide at the mouth and opens to 2mm at the bottom, so the lips squeeze the panel as it goes in, and the 10mm-deep slot grips a long strip of each face. Below the slot sits a 3mm solid, rounded base that takes the knocks and keeps fingers, cables and other parts off a sharp edge. Supplied as one continuous 50m coil (works out at about £10.06 per metre inc VAT).
At a glance
- Fits 2mm panels only: sheet steel, aluminium, polycarbonate, acrylic, glass and board
- 8mm wide x 13mm high teardrop section, round on the outside face
- Tapered 1mm to 2mm slot, 10mm deep: friction grip, no adhesive needed on a clean edge
- 60 Shore A TPE: firm enough to hold, soft enough to bend round curves
- 59 g per metre, about 3kg for the full 50m coil
- Cuts cleanly with a sharp knife or shears; 100% recyclable material
- Held in UK stock for same-day dispatch
Technical drawing

Specification
| Property | Value | Basis / test method |
|---|---|---|
| Profile | Teardrop U channel, round base | Manufacturer drawing |
| Overall width (widest point of bulb) | 8 mm | Manufacturer drawing, nominal |
| Overall height | 13 mm | Manufacturer drawing, nominal |
| Slot width at mouth | 1 mm | Manufacturer drawing, nominal |
| Slot width at base | 2 mm | Manufacturer drawing, nominal |
| Slot depth (grip length) | 10 mm | Manufacturer drawing, nominal |
| Solid base under slot | 3 mm | Manufacturer data (13 mm height minus 10 mm slot) |
| Fits panel / clamping range | 2 mm to 2 mm (2 mm only) | Manufacturer datasheet |
| Material | Thermoplastic elastomer (TPE) | Manufacturer datasheet |
| Hardness | 60 Shore A | Shore A durometer (manufacturer datasheet) |
| Colour | Black | Manufacturer datasheet |
| Weight | 59 g/m (about 2.95 kg per 50 m coil) | Manufacturer datasheet |
| Use temperature (design range) | −25 °C to +70 °C | Manufacturer datasheet RC234 |
| Short-term temperature limits | −40 °C to +90 °C | Manufacturer web technical table (use the datasheet range above for design) |
| Dimensional tolerance | ISO 3302-1 class E2 (cross-section) / L2 (length) | ISO 3302-1 |
| Coil length | 50 m continuous | Manufacturer data |
| Recyclability | 100% recyclable | Manufacturer statement |
| Density, tensile strength, elongation, tear, compression set | Not published for this profile | Ask us if your specification needs them |
Materials and compliance
Made from a black thermoplastic elastomer (TPE) at 60 Shore A. TPE behaves like a rubber in use, flexing and recovering its shape after compression, but it is processed like a thermoplastic, which is why it can be fully recycled. The manufacturer states good resistance to tearing, abrasion, chemicals and repeated flexing for this profile.
The manufacturer does not state any food-contact, drinking-water, fire-rating or REACH/RoHS approval in writing for this product, so we do not claim one. If you need a certified grade, contact us before ordering.
How it fits

- Deburr the panel edge and wipe it with a grease remover; a clean edge grips noticeably better.
- Start at one end and press the slot over the edge by hand, working along a short length at a time.
- Seat it fully with a rubber or nylon mallet until the panel reaches the bottom of the 10mm slot.
- Cut to length with a sharp knife or shears. Leave it a few millimetres long on long runs and push the ends together so they butt tightly.
Typical uses
- Exposed edges of 2mm sheet-metal guards, covers and enclosures
- Glazing and polycarbonate panel edges
- Running boards, steps and stair edges
- Vending machines, kiosks and display cabinets
- Furniture and shopfitting panels
Why buy it from us
- Held in stock in the UK and dispatched the same day on orders placed before the cut-off
- Every dimension published, with a drawing you can drop straight into a spec or a quote
- Real people on the phone who can check fit before you order: +44 1282 277786
Complete your project
- TPE U Channel Edge Trim 7.5mm x 12mm (for 1mm panels)
- Black PVC Self-Grip Edge Trim 10.5mm x 14.5mm
- PVC Self-Grip Edge Trim 14mm x 16.2mm
Frequently asked questions
Will it fit a 1.5mm or 3mm panel?
No. The clamping range is 2mm only. On thinner sheet it will be loose and can work off; on thicker sheet it will not seat to the bottom of the slot. Call us and we will point you to the right size.
Do I need glue?
Not usually. The slot narrows to 1mm at the mouth, so the lips pinch a 2mm panel along the full 10mm grip. On edges that get pulled or vibrate hard, a few dots of flexible adhesive in the slot add security.
How do I measure what I need?
Measure the panel thickness with calipers (it must be 2mm), then add up the length of every edge you want to cover plus about 5% for trimming. One coil covers 50 metres.
Will it go round corners and curves?
Yes. 60 Shore A TPE bends round gentle curves without kinking. For a tight outside corner, cut a small V-notch out of the base at the bend so the trim lies flat.
What temperatures can it take?
The manufacturer's datasheet gives a working range of −25 °C to +70 °C, and its web data lists −40 °C to +90 °C as limits. Design to the datasheet range; ask us if your application runs hotter.
How do I cut and join it?
Cut square with a sharp knife or shears. Butt the ends tightly together. Where a sealed join is needed, a cyanoacrylate adhesive suitable for TPE gives a neat bond.
Is it suitable outdoors?
TPE has good chemical and abrasion resistance and is widely used outside, but the manufacturer does not publish UV or ozone test data for this profile. For long-term outdoor exposure, talk to us first.
What is it made of, and can it be recycled?
Black thermoplastic elastomer (TPE). It can be re-melted, so offcuts are 100% recyclable.
Not sure it is the right size? Email sales@industrial-polymers.co.uk or call +44 1282 277786.
Product details
| SKU | IP-TPEU-8X13-STD |
|---|---|
| Weight | 7.05 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:TPE U Channel Edge Trim – 8mm x 13mm for 2mm Panels – 50m Coil