
Rubber & FoamSKU IP-TPEU-7.5X12X1-RED
TPE U Channel Edge Trim – 7.5mm x 12mm Teardrop for 1mm Panels – Red – 50m Coil
A push-on impact edge for 1 mm sheet. This red TPE U channel has a teardrop section: 2 mm across the top, widening to a 7.5 mm rounded bulb with a 3.8 mm solid base. A 1 mm slot runs 8.2 mm deep, so the trim grips well down both faces of the sheet. Knocks land on the rubber bulb, not on the sheet edge. No adhesive is needed, and it pulls off again for reuse. Supplied as one continuous 50 m coil, held in stock.
At a glance
- Fits: 1 mm thick sheet only (steel, aluminium, glass, acrylic, board)
- Section: 7.5 mm wide × 12 mm high, teardrop U with a rounded base
- Grip: 1 mm slot, 8.2 mm deep, tapered sides
- Protection: 3.8 mm of solid TPE between the sheet edge and whatever hits it
- Material: TPE, 60 Shore A, 100% recyclable, cuts with a knife
- Coil: 50 m, works out at about £10.71 per metre inc VAT
Technical drawing

Specification
| Property | Value | Source / test method |
|---|---|---|
| Profile | Teardrop U channel with rounded solid base | Manufacturer's drawing |
| Overall width (widest point of bulb) | 7.5 mm | Manufacturer's drawing |
| Width at top (open end) | 2 mm | Manufacturer's product data |
| Overall height | 12 mm | Manufacturer's drawing |
| Slot width | 1 mm | Manufacturer's drawing |
| Slot depth (grip length on each face) | 8.2 mm | Manufacturer's product data (12 mm − 3.8 mm base) |
| Solid base under the slot | 3.8 mm | Manufacturer's drawing |
| Panel / edge thickness it fits | 1 mm only (clamping range 1 to 1 mm) | Manufacturer's datasheet |
| Coil length | 50 m continuous | Manufacturer's product data |
| Weight | 67 g/m (about 3.35 kg per 50 m coil) | Manufacturer's datasheet |
| Material | Thermoplastic elastomer (TPE), single material | Manufacturer's datasheet |
| Colour | Red | Manufacturer's product data (see note below) |
| Hardness | 60 Shore A | Shore A durometer; method not stated by the manufacturer |
| Service temperature | −25 °C to +70 °C | Manufacturer's datasheet (see note below) |
| Dimensional tolerance | ISO 3302-1, class E2 (section) / L2 (length) | ISO 3302-1 |
| Density | Not published for this profile | Ask us |
| Tensile strength / elongation at break | Not published for this profile | Ask us |
| Tear strength / compression set | Not published for this profile | Ask us |
| Recyclability | 100% recyclable | Manufacturer's product data |
Notes: The manufacturer's sales data gives an operating range of −40 °C to +90 °C, but its datasheet for this part gives −25 °C to +70 °C. We quote the narrower datasheet figure; design to it for continuous service. The sales data lists this part as red, while the datasheet template shows black. If colour matters for your job, call us before ordering and we will confirm it against stock.
Materials and compliance
The trim is a single-material thermoplastic elastomer (TPE): rubber-like and flexible, but meltable, so offcuts can be recycled. TPE resists flexing fatigue and many chemicals well, and has good tear and abrasion resistance. Dimensions are held to ISO 3302-1 tolerance classes E2/L2.
The manufacturer does not state any food-contact, potable-water, fire or REACH/RoHS approval for this exact part, so we do not claim one. If you need a certificate for your application, ask us before ordering.
Where it is used
- Thin sheet-metal panels, guards and enclosure edges
- Glass and acrylic sheet edges, including protection in transit
- Vending machine and kiosk panels
- Furniture and shopfitting panels
- Vehicle running boards and step edges
- Stair nosings and exposed edges that people brush past
How it fits

- Deburr the edge and wipe off oil or grease with a degreaser. The trim grips noticeably better on a clean, smooth edge.
- Start at one end and press the slot over the sheet, working along in short sections. Use a rubber mallet for a firm seat.
- On outside corners, ease the trim round in a smooth curve. Do not stretch it: stretched TPE shrinks back and leaves gaps at the ends.
- Cut to length with a sharp knife or trim shears, leaving the ends square for a neat butt joint.
Frequently asked questions
What thickness of panel does it fit?
Only 1 mm. The slot is 1 mm wide, so thinner sheet will be loose and thicker sheet will split or lift the trim. For 1–3 mm sheet, see the 8.5 × 12 mm TPE U channel linked below.
How deep does it go onto the panel?
The slot is 8.2 mm deep, so the trim covers about 8 mm of each face of the sheet. The rounded base sits 3.8 mm beyond the edge.
Do I need adhesive?
No. The tapered slot grips the sheet on its own and the trim can be pulled off and reused. On vibrating or frequently handled edges, a few dabs of a flexible adhesive in the slot will stop it creeping.
What temperatures can it take?
Design to −25 °C to +70 °C, the datasheet figure. TPE gets stiffer in the cold and softer in the heat. Near the ends of that range, it grips best if fitted at room temperature.
Can it be used outdoors?
Yes, it is used on vehicle steps and outdoor panels. The manufacturer does not publish a UV rating for this part, so for long, continuous sun exposure ask us about alternatives.
How do I cut and join it?
It cuts cleanly with a sharp knife or shears. For a closed loop, butt the two square-cut ends tightly together; a spot of cyanoacrylate (superglue) on the ends gives a neat, permanent joint.
Can I buy it by the metre?
This listing is the full 50 m coil (about £10.71/m inc VAT). For shorter lengths or larger quantities, call or email us for a quote.
Is it the same as rubber?
It feels and flexes like soft rubber at 60 Shore A, but TPE is a thermoplastic, so it is recyclable and does not need vulcanising.
Related TPE U channels
- TPE U Channel – 8.5mm x 12mm for 1mm to 3mm panels – 100m coil
- TPE U Channel – 6mm x 12.5mm J profile for 0.5mm to 1.5mm panels – 50m coil
- TPE U Channel – 4.5mm x 12mm deep grip for 1.5mm edges – 50m coil
Questions about fit or quantities? Call +44 1282 277786 or email sales@industrial-polymers.co.uk.
Product details
| SKU | IP-TPEU-7.5X12X1-RED |
|---|---|
| Weight | 7.94 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:TPE U Channel Edge Trim – 7.5mm x 12mm Teardrop for 1mm Panels – Red – 50m Coil