
Rubber & FoamSKU IP-TPEU-9X20-STD
TPE U Channel with Foam Bead – 9mm x 20mm for 1.2mm to 2.5mm Panels – 50m Coil
A push-on edge trim and cushion seal in one profile. The firm 80 Shore A TPE U grips 1.2mm to 2.5mm sheet with four internal ridges, so no adhesive is needed. A 9.5mm hollow TPE foam bead runs along the closed side of the U. It takes knocks and closes small gaps against a door or frame. Supplied as one continuous 50m coil in black, ready for same-day dispatch.
At a glance
- Size: 9mm wide x 20mm high overall (13.4mm U body + foam bead)
- Fits: 1.2mm to 2.5mm panel edges
- Grip: two pairs of internal ridges (four in total), push on by hand, no glue, can be removed and refitted
- Bead: 9.5mm diameter hollow foam bead with a 1mm wall, co-extruded the full length
- Material: TPE base, TPE foam bead, recyclable
- Coil: 50m continuous, £17.73 per metre equivalent
Technical drawing

Specifications
| Property | Value | Basis / test method |
|---|---|---|
| Overall size (W x H) | 9mm x 20mm | Supplier drawing, nominal |
| U body height (without bead) | 13.4mm | Supplier drawing, nominal |
| Overall width | 9mm | Supplier drawing, nominal |
| Foam bead | 9.5mm diameter, hollow, 1mm wall | Supplier drawing, nominal |
| Base thickness (thickest point) | 3mm | Supplier drawing / technical data |
| Slot width (inside, at base) | 3.5mm | Supplier drawing, nominal |
| Clamping range (panel thickness) | 1.2mm to 2.5mm | Supplier rating; slightly thicker sheet may fit, test first |
| Gripping ridges | 4 (2 pairs) | Supplier description |
| Material | TPE (thermoplastic elastomer) base, TPE foam bead | Supplier technical data |
| Hardness | 80 Shore A (base) | Supplier rating (Shore A). Bead hardness not stated |
| Service temperature | -40°C to +90°C | Supplier rating |
| Dimensional tolerance | ISO 3302-1 class E2 (cross-section) / L2 (length) | ISO 3302-1 |
| Colour | Black | - |
| Coil length | 50m continuous | - |
| Density, tensile strength, elongation, tear, compression set | Not published for this profile | Ask us if your specification needs them |
Materials and compliance
The base is a thermoplastic elastomer (TPE) and the bead is a co-extruded TPE foam. TPE needs no vulcanising, so offcuts can be recycled. It resists flexing fatigue, tearing, abrasion and many common chemicals. No food-contact, fire, REACH or RoHS approval is stated for this profile, so we do not claim one. If your project needs a certificate, contact us before ordering.
Typical uses
- Edge trim and soft closing seal on 1.2mm to 2.5mm sheet-metal cabinets, enclosures and machine guards
- Protective edging on access panels, hatches and inspection doors
- Glazing and screen contours, vending machines and kiosks
- Running boards, stair edges and furniture panels
- Covering sharp cut sheet edges in transport and handling
Which one do I need?
| Profile | Suits |
|---|---|
| Self-grip top seal, 0.8mm to 2mm | Thinner panels, sold per metre |
| TPE U with foam bead 9mm x 20mm (this item) | 1.2mm to 2.5mm panels, edge protection and cushion seal, 50m coil |
| Self-grip top seal, 1.6mm to 3mm | Slightly thicker panels |
| EPDM U channel 7mm x 21mm | 2mm panels where only edge protection is needed |
How much do I need?
Add up every edge you want to trim. For example, twelve 800mm x 600mm cabinet doors trimmed all round need 12 x 2.8m = 33.6m, so one 50m coil covers them with spare. Allow a few centimetres per run for tight butt joints.
Fitting
- Deburr and clean the panel edge so it does not cut the gripping ridges.
- Start on a straight section with the U opening over the panel edge and the bead facing outwards.
- Press the trim on by hand, or tap it with a rubber mallet, until the edge sits fully at the base of the slot.
- Work round corners gradually. Warming the trim slightly helps on tight radii.
- Cut each run a little long with a sharp knife or trim cutter so the ends butt tightly.
Frequently asked questions
What panel thickness does it fit?
It is designed for 1.2mm to 2.5mm sheet. Slightly thicker sheet may fit, but test a short piece first. For thinner panels, look at the self-grip top seal for 0.8mm to 2mm.
Do I need glue or clips?
No. The four internal ridges hold it on the edge. You can pull it off and refit it, for example during maintenance.
Where does the foam bead sit once fitted?
The bead runs along the closed side of the U, so it sits over the edge of the panel. When a door closes, the bead compresses against the frame and takes the impact.
How do I cut and join it?
Cut it square with a sharp knife or trim cutter. Butt the ends tightly; no joining compound is needed for most edge-trim uses. On corners, bend the trim round rather than mitring it so the bead stays continuous.
What temperatures can it take?
The supplier rates it from -40°C to +90°C, so it suits unheated outdoor cabinets and warm machine enclosures. It is not for oven or exhaust edges.
Is it suitable outdoors?
Yes. TPE handles weather, flexing and many chemicals well. Check compatibility first if the trim will see oils or solvents for long periods.
Can I order a cut length instead of 50m?
This listing is for a full 50m coil. For a smaller quantity, contact us.
Is it food-safe or fire rated?
No approval is stated for this profile, so we do not claim one. Contact us and we can suggest a certified alternative.
Need help choosing? Contact our technical team on +44 1282 277786 or sales@industrial-polymers.co.uk with your panel thickness and application.
Product details
| SKU | IP-TPEU-9X20-STD |
|---|---|
| Weight | 11.02 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:TPE U Channel with Foam Bead – 9mm x 20mm for 1.2mm to 2.5mm Panels – 50m Coil