
Rubber & FoamSKU IP-EPDMU-7X21-6M
EPDM U Channel – 7mm x 21mm for 2mm Panels – 6m to 30m Lengths
Price shown updates with the option you pick.
A tall, deep-gripping edge trim for 2 mm panels. This solid black EPDM U channel is 7 mm wide and 21 mm high, with a 2 mm slot that runs 18.5 mm deep and a fully rounded base. The long legs cover a wide band on both faces of the sheet, so it hides rough or uneven cut edges and gives a broad cushioned strip against knocks. Choose one continuous length from 6 m to a full 30 m coil, in 1 m steps. Every length is held in stock in the UK.
At a glance
- Fits 2 mm panels: the 2 mm slot grips both faces of 2 mm sheet metal, glass, acrylic, polycarbonate or board.
- Deep 7 × 21 mm profile: 18.5 mm deep legs with 2.5 mm walls and a 2.5 mm rounded base.
- Solid EPDM, 65–75 Shore A: tensile strength 10 MPa, elongation at break 500%, tear strength 50 kN/m.
- Made for outdoor use: no cracks after the 72 h ozone test, with good resistance to weathering, heat, cold, flexing and abrasion.
- No special tools: push on by hand and cut with a sharp knife. Bond with PU or silicone sealant for a permanent or sealed fit.
- Any length from 6 m to 30 m: one continuous piece. The 30 m full coil has the lowest price per metre.
Technical drawing

Nominal dimensions in mm. Overall width, height, slot width and the 18.5 mm inside depth are the manufacturer's figures. The 2.5 mm wall is (7 − 2) ÷ 2 and the 2.5 mm base is 21 − 18.5; both agree with the 2.5 mm thickness on the manufacturer's data.
Specifications
| Property | Value | Test method / source |
|---|---|---|
| Profile type | Round-base U channel (edge trim) | Manufacturer's drawing |
| Overall width | 7 mm | Manufacturer's drawing, nominal |
| Overall height | 21 mm | Manufacturer's drawing, nominal |
| Slot (channel) width | 2 mm | Manufacturer's drawing, nominal |
| Inside (slot) depth | 18.5 mm | Manufacturer's drawing, nominal |
| Fits panel thickness | 2 mm | Manufacturer's data sheet |
| Wall thickness | 2.5 mm | Manufacturer's data; (7 − 2) ÷ 2 |
| Base thickness | 2.5 mm (calculated) | 21 − 18.5 |
| Material | Solid EPDM (ethylene propylene diene monomer) | Manufacturer's data sheet |
| Colour | Black | – |
| Hardness | 65–75 IRHD (±5), about 65–75 Shore A | IRHD, manufacturer's data sheet |
| Tensile strength | 10 MPa | Manufacturer's data sheet |
| Elongation at break | 500% | Manufacturer's data sheet |
| Tear strength | 50 kN/m | Manufacturer's data sheet |
| Compression set | 21% | 22 h at 70 °C |
| Ozone resistance | No cracks | 72 h at 40 °C, 25 pphm |
| Heat ageing: change in tensile strength | +9% | 70 h at 70 °C |
| Heat ageing: change in elongation at break | 0% | 70 h at 70 °C |
| Weight | 0.13 kg per metre (30 m coil about 3.9 kg) | Manufacturer's data |
| Lengths available | 6, 7, 8 … 29 m, or a full 30 m coil (one continuous piece) | – |
| Service temperature | about −40 °C to +120 °C, typical for EPDM, not tested on this profile | General EPDM data |
| Density | Not stated for this profile | – |
| Dimensional tolerance | Not stated; extruded rubber is normally made to ISO 3302-1 tolerance classes | – |
Materials and compliance
This profile is extruded from a solid EPDM compound. EPDM resists weathering, ozone, UV and water, and stays flexible over time. The test results in the table come from the manufacturer's data sheet for this profile.
The manufacturer does not state any food-contact, WRAS, REACH, RoHS or fire approval for this product, so we do not claim one. If your application needs a certified material, please contact us before ordering.
How it fits

Choosing your length
Add up the total length of edge to be covered and allow about 5% extra for cutting and joints. For example, two 2 mm guard panels of 1,000 × 800 mm edged all round need 2 × 3.6 m = 7.2 m, or about 7.6 m with allowance, so choose 8 m. The price covers one continuous piece of the length you choose.
| Length | Price inc VAT | Price per metre |
|---|---|---|
| 6 m | £181.77 | £30.30 |
| 10 m | £302.94 | £30.29 |
| 15 m | £454.41 | £30.29 |
| 20 m | £605.88 | £30.29 |
| 25 m | £757.35 | £30.29 |
| 30 m full coil | £784.80 | £26.16 |
Need 26 m or more? The full 30 m coil costs less than the 26 m, 27 m, 28 m or 29 m lengths.
Typical uses
- Sheet metal machine guards, covers and enclosure doors where a wide protective band is wanted
- Protective edge on 2 mm glass, acrylic and polycarbonate panels and screens
- Hiding rough, burred or uneven cut edges on 2 mm sheet and board
- Vending machines, kiosks, shop fittings and furniture panels
- Stairs, steps, kick plates and running boards made from 2 mm sheet
- Bonded into aluminium channels as a push-in glazing or panel seal
Fitting
- Deburr and clean the edge. Check the sheet is 2 mm thick.
- Start at a corner and press the channel on by hand, working along the edge. A soft-faced mallet helps on long runs.
- On outside corners, ease the trim round the bend. On tight corners, cut a small V-notch out of the legs.
- Cut a few millimetres long with a sharp knife, then push the ends together into a tight butt joint.
- For a sealed or permanent fit, run a bead of PU or silicone sealant into the slot first.
FAQ
What panel thickness does it fit?
2 mm panels. On 1.5 mm sheet the grip will be loose: bond it with sealant, or choose the 5.5 × 19.7 mm or 5.6 × 19 mm channel for 1.6 mm sheet. For 4.8 mm panels choose the 12.8 × 21.5 mm channel. A 3 mm edge will not fit this slot.
Why choose the 21 mm height?
The 18.5 mm deep legs cover far more of each face than a standard 9–10 mm trim. That hides rough cuts, holds on more firmly and gives a wider cushioned strip against knocks.
How do I measure what I need?
Measure the panel thickness with a caliper first, then measure the total edge length in metres and round up. Allow about 5% extra for cuts and joints.
Can it be used outdoors?
Yes. EPDM is chosen for outdoor use because it resists weathering and ozone. This compound passed a 72 h ozone test with no cracks.
What temperatures can it take?
The manufacturer has not published a temperature range for this profile. EPDM is typically used from about −40 °C to +120 °C, but this has not been tested on this profile. The compound did pass heat ageing for 70 h at 70 °C with little change in properties.
How do I cut and join it?
Use a sharp knife or heavy shears and cut square. Butt the ends together tightly. For a sealed joint, add a little cyanoacrylate glue or sealant to the cut faces.
Will it go round corners?
It follows gentle curves easily. For sharp outside corners, notch the legs from the inside so the base bends neatly, or cut and butt-join the ends.
Is it soft or firm?
At 65–75 Shore A it is medium-firm: soft enough to absorb knocks, and firm enough to hold its shape and grip the panel.
Why is the 30 m coil cheaper than 26 m to 29 m?
30 m is a full, uncut coil, so there is no cutting or handling, and it is priced lower per metre.
Is it food-safe or certified?
The manufacturer states no food-contact or other approvals for this product, so we do not claim any. Ask us about certified alternatives.
Is it in stock?
Yes. All lengths are held in stock and dispatched from the UK.
Related profiles
- EPDM U Channel 5.5 × 19.7 mm, for 1.6 mm panels
- EPDM U Channel 5.6 × 19 mm, for 1.6 mm panels
- EPDM U Channel 5.7 × 17 mm, for 1.5–2.5 mm panels
- EPDM U Channel 8.4 × 21 mm, 50 m coil
- EPDM U Channel 12.8 × 21.5 mm, for 4.8 mm panels
- EPDM Square U Channel 14.7 × 22 mm
Need help choosing? Call +44 1282 277786 or email sales@industrial-polymers.co.uk.
Product details
| SKU | IP-EPDMU-7X21-6M |
|---|---|
| Weight | 1.72 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM U Channel – 7mm x 21mm for 2mm Panels – 6m to 30m Lengths