
Rubber & FoamSKU IP-EPDM-8X9-14
EPDM Square U Channel – 8mm x 9mm – Fits 5mm Panel – Black Rubber Edge Trim
Price shown updates with the option you pick.
A neat, square-edged rubber channel that pushes onto 5mm panels. This solid black EPDM U channel is 8mm wide and 9mm high, with a 5mm slot 7.5mm deep and 1.5mm walls. It covers sharp or rough edges on sheet metal, acrylic, polycarbonate, glass, MDF and ply, and takes knocks so the panel edge does not. EPDM shrugs off rain, UV and ozone, so it is as happy outdoors as on a machine in the workshop.
Choose one continuous length from 14m to 30m. The full 30m coil is the best value per metre. Held in UK stock.
At a glance
- Fits: panels and sheet 5mm thick
- Profile: 8mm wide × 9mm high, square outer corners
- Slot: 5mm wide × 7.5mm deep, so it grips 7.5mm of the panel face
- Walls and base: 1.5mm solid EPDM
- Hardness: 65–75 Shore A: firm enough to hold its shape, soft enough to cut with a knife
- Lengths: 14m to 29m in 1m steps, or a full 30m coil, always one continuous piece
Technical drawing

Specifications
| Property | Value | Test method / source |
|---|---|---|
| Overall width | 8.0 mm | Nominal, supplier drawing |
| Overall height | 9.0 mm | Nominal, supplier drawing |
| Slot (channel) width | 5.0 mm | Nominal, supplier drawing |
| Slot depth | 7.5 mm | Nominal, supplier drawing |
| Wall thickness (each side) | 1.5 mm | Supplier technical data |
| Base thickness | 1.5 mm | Calculated: 9 mm height − 7.5 mm slot depth |
| Fits panel thickness | 5 mm | Supplier data ("to fit panel") |
| Cross-section area | 34.5 mm² | Calculated from the nominal dimensions |
| Material | Solid EPDM (ethylene propylene diene monomer) | Supplier material specification |
| Colour | Black | — |
| Hardness | 65–75 Shore A (65–75 ±5 IRHD) | Supplier material specification (IRHD) |
| Tensile strength | 10 MPa | Supplier material specification |
| Elongation at break | 500 % | Supplier material specification |
| Tear strength | 50 kN/m | Supplier material specification |
| Compression set | 21 % | 22 h at 70 °C (supplier material specification) |
| Ozone resistance | No cracks | 72 h at 40 °C, 25 pphm ozone |
| Heat ageing: change in tensile strength | +9 % | 70 h at 70 °C |
| Heat ageing: change in elongation | 0 % | 70 h at 70 °C |
| Weight | 0.04 kg per metre (about 1.2 kg for 30 m) | Supplier data |
| Density | About 1.16 g/cm³ | Calculated from 0.04 kg/m and 34.5 mm² area |
| Service temperature | About −40 °C to +120 °C | Typical for EPDM, not tested on this profile |
| Dimensional tolerance | Not stated by the manufacturer; nominal sizes | Ask us if you need a toleranced drawing |
| Supplied as | One continuous length, 14 m to 30 m | — |
Materials and compliance
Made from a solid EPDM rubber compound, which the manufacturer describes as 100% recyclable. The manufacturer does not state any food-contact (FDA, EC 1935/2004), drinking-water (WRAS), REACH, RoHS or fire-rating approval for this profile, so please do not specify it where one of those is required. If you need a certified grade, call us and we will suggest one.
Which length, and what does it cost per metre?
| Length | Price inc VAT | Per metre |
|---|---|---|
| 14m | £282.75 | £20.20 |
| 15m | £302.94 | £20.20 |
| 20m | £403.92 | £20.20 |
| 25m | £504.90 | £20.20 |
| 29m | £585.69 | £20.20 |
| 30m full coil | £576.00 | £19.20 |
Every length from 14m to 29m is £20.20 per metre. The full 30m coil costs less than 29m, so if you need 29m or more, buy the coil. To work out how much you need, add up the edges you want to cover and allow about 5% for trimming. For example, four sides of a 1.2m × 0.8m panel is 4m.
How to fit it
- Clean the edge and remove burrs, grease and dust.
- Start at one end and press the channel onto the edge with your thumbs, working along the panel. A soft rubber mallet helps on long runs.
- Go round gentle curves in one piece. On a sharp corner, cut a V notch out of the walls (not the base) so the channel folds neatly.
- Cut square with a sharp knife or snips and butt the ends tightly together.
- For a permanent fix or a weather seal, run a bead of polyurethane or silicone sealant in the slot before you push it on.
Typical uses
- Edges of 5mm aluminium, steel and stainless sheet
- 5mm acrylic and polycarbonate guards, screens and display panels
- Glass and glazing edges in frames and cabinets
- Vending machines, kiosks, enclosures and equipment covers
- Doors, hatches, shelving and stair edges
- Trailers, horseboxes, boats and caravans
Frequently asked questions
What panel thickness does it fit?
5mm. The slot is 5mm wide, so it grips a 5mm panel snugly. For 4mm or 4.5mm material you can fit it with a bead of sealant in the slot; for 6mm or thicker choose a wider channel.
Will it stay on without glue?
On a clean 5mm edge it holds by friction for most guarding and trim jobs. Where it will be knocked often, pulled or exposed to weather, bond it in with polyurethane or silicone sealant.
How do I cut and join it?
A sharp craft knife, snips or a fine-toothed saw all cut it cleanly. Butt the ends together on a straight run. For a sealed joint, use a dab of instant adhesive for rubber on the end faces.
Can it go round corners?
It follows gentle curves in one piece. For a 90° corner, cut a V notch out of both walls so the base bends, or mitre two pieces at 45°.
Is it suitable for outdoor use?
Yes. EPDM has very good resistance to weather, UV and ozone; the material passed the supplier's 72-hour ozone test with no cracks.
What temperature can it take?
The manufacturer does not give a temperature range for this profile. EPDM is typically used from about −40 °C to +120 °C, and this compound kept its strength after 70 hours at 70 °C.
Is it oil resistant?
No. EPDM swells in mineral oil, petrol and diesel. It is good with water, steam, mild acids and alkalis. For oily areas, ask us about a nitrile or neoprene channel.
Is it food safe?
No food-contact approval is stated for this product, so do not use it where it touches food.
Is it one piece?
Yes. Whatever length you choose comes as one continuous piece, coiled for delivery.
Related products
- EPDM Square U Channel – 8.75mm x 14mm (deeper grip)
- EPDM Square U Channel – 12mm x 23mm
- PVC Self-Grip Edge Trim – 9.5mm x 14mm for 1–3mm panels
Data sheet
Download the technical data sheet (PDF)
Need a different size or a toleranced drawing? Call +44 1282 277786 or email sales@industrial-polymers.co.uk.
Product details
| SKU | IP-EPDM-8X9-14 |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM Square U Channel – 8mm x 9mm – Fits 5mm Panel – Black Rubber Edge Trim