
Rubber & FoamSKU IP-PVCET-10.5X14.5-50M
PVC Self-Grip Edge Trim – 10.5mm x 14.5mm for 3mm to 5mm Panels – 50m Coil
A black PVC push-on edge trim with a steel carrier, made for panel edges from 3 mm to 5 mm thick. It is 10.5 mm wide and 14.5 mm high, with a 12 mm deep channel and a 2.5 mm thick crown over the edge. A U-shaped steel strip runs through the PVC for its whole length and a gripping fin inside the channel folds onto the panel, so it holds by clamping force alone, with no glue. It covers sharp cut edges, protects the panel from knocks and leaves a neat rounded finish. It comes as one continuous 50 m coil and is in stock in the UK for same-day dispatch.
At a glance
- Fits: sheet metal, plastic, fibreglass, glass and board edges 3 mm to 5 mm thick
- Size: 10.5 mm wide × 14.5 mm high; 12 mm inside depth; 3 mm mouth before fitting
- Construction: flexible PVC, 70° Shore A, over a U-shaped steel carrier, 2.5 mm section
- Grip: internal gripping fin; push on by hand, no adhesive, and it can be removed and refitted
- Working temperature: −10 °C to +60 °C, indoors or outdoors
- Supplied as: a 50 m coil in one piece, £506.58 inc VAT (about £10.13 per metre)
Technical drawing

All dimensions are in mm and nominal. The drawing is not to scale; the carrier and fin shapes are shown as typical.
Specifications
| Property | Value | Test method / basis |
|---|---|---|
| Profile | Self-gripping U edge trim with steel carrier and one internal gripping fin | Manufacturer drawing |
| Overall width | 10.5 mm | Manufacturer drawing and data sheet |
| Overall height | 14.5 mm | Manufacturer drawing and data sheet |
| Inside depth (grip depth) | 12 mm | Manufacturer drawing |
| Mouth opening (before fitting) | 3 mm; the lips spread open over thicker panels | Manufacturer drawing |
| Panel thickness it fits | 3 mm to 5 mm | Manufacturer page and range data sheet |
| Section thickness | 2.5 mm | Manufacturer data |
| Cover over the panel edge (crown) | 2.5 mm | Calculated: 14.5 − 12 mm |
| Jacket material | Flexible PVC | Manufacturer |
| Carrier | Steel, U-shaped, full length | Manufacturer |
| Colour | Black | Manufacturer |
| Hardness | 70° Shore A | Manufacturer data; method not stated |
| Density | 1.35 to 1.45 g/cm³ | Manufacturer data; method not stated |
| Tensile strength | More than 11 MPa | Manufacturer data; method not stated |
| Elongation at break | More than 260 % | Manufacturer data; method not stated |
| Minimum working temperature | −10 °C | Manufacturer data |
| Maximum working temperature | +60 °C | Manufacturer data |
| Tear strength | Not stated for this profile | Ask us if you need it |
| Compression set | Not stated for this profile | Ask us if you need it |
| Dimensional tolerance | Not stated; dimensions are nominal | Ask us if you need it |
| Weight | Not stated for this profile | Ask us if you need it for carriage |
| Supplied as | One continuous 50 m coil | Manufacturer |
How it fits

- Check the edge. Measure the panel: it must be 3 mm to 5 mm thick. Deburr it and wipe it clean and dry.
- Push on. Start at one end and press the trim fully home by hand, working along the edge. The lips open up over the panel.
- Seat it. Tap along the top with a rubber or plastic mallet, especially on curves and corners. No glue is needed.
- Cut and finish. Cut through the PVC and steel with heavy side cutters or a fine hacksaw. Butt the ends tightly together.
Typical uses
- Sharp edges of 3 mm to 5 mm steel and aluminium machine guards, enclosures and cabinets
- Conveyor side guards and machine frames
- Garage door and shed panels
- Fibreglass panels and marine equipment
- Playground and leisure equipment, for safety edging
- Vehicle interior side panels, side window edges, glass and furniture panels
Which edge trim do I need?
| Panel thickness | Best match |
|---|---|
| 1 mm to 1.5 mm | Self-Grip PVC Edge Trim 5.5 × 8.5 mm |
| 1 mm to 3 mm | Self-Grip PVC Edge Trim 9.5 × 14 mm |
| 3 mm to 5 mm | This trim, 10.5 × 14.5 mm |
| 3.5 mm to 4.5 mm, cut to length | Self-Grip PVC Edge Trim 10 × 13.5 mm |
| 4 mm to 5 mm | Self-Grip PVC Edge Trim 11 × 16.5 mm |
| 6 mm to 8 mm | Self-Grip PVC Edge Trim 14 × 16.2 mm |
Materials and compliance
The jacket is flexible PVC and the carrier is steel. The PVC resists weather, moisture and many common chemicals, which suits it to indoor and outdoor use within −10 °C to +60 °C. The manufacturer does not state any approvals (such as FDA, REACH or RoHS) for this profile, so we do not claim any. If you need a declaration for your project, contact us before ordering.
Frequently asked questions
How do I fit it?
Push it onto the clean edge by hand, starting at one end, then tap it home with a rubber mallet. The steel carrier and the inner fin grip the panel, so no glue or fixings are needed.
What panel thickness does it fit?
3 mm to 5 mm. The 3 mm mouth spreads open as it goes on, so the steel carrier clamps the panel from both sides. On sheet thinner than 3 mm it will not grip firmly; see the table above for trims that fit other thicknesses.
How much will I get from one coil?
One 50 m coil in a single piece. Add up the length of every edge to be covered; for example, twenty guard panels with a 2.4 m top edge need 48 m, so one coil covers them.
Will it go round corners and curves?
Yes. The steel carrier lets it bend around gentle curves and radiused corners and hold the shape. On a tight corner, tap it home with a mallet as you go. For a sharp 90° corner, cut it and butt the two ends.
How do I cut and join it?
Cut through the PVC and the steel carrier with heavy side cutters or a fine-tooth hacksaw. There is no jointing piece; butt the cut ends tightly together on the edge.
Can it be used outdoors?
Yes. The PVC jacket resists weather and moisture. Its working range is −10 °C to +60 °C, so it suits UK outdoor use but not hot areas such as engine bays or ovens.
Can I remove it and use it again?
Yes. Because it holds by grip rather than adhesive, it can be pulled off and refitted, although the fin grips best the first time.
Is it a food-grade or certified material?
No approvals are stated for this profile. It is a general-purpose protective trim; ask us if you need a certified material.
Need help choosing? Call +44 1282 277786 or email sales@industrial-polymers.co.uk.
Product details
| SKU | IP-PVCET-10.5X14.5-50M |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:PVC Self-Grip Edge Trim – 10.5mm x 14.5mm for 3mm to 5mm Panels – 50m Coil