
Rubber & FoamSKU IP-PVCET-5.5X8.5-14M
Self-Grip PVC Edge Trim – 5.5mm x 8.5mm – for 1mm to 1.5mm Panels – 14m to 50m
Price shown updates with the option you pick.
A slim black PVC edge trim with a steel carrier that clips onto 1 mm to 1.5 mm sheet edges with no glue. It is 5.5 mm wide and 8.5 mm high. A U-shaped steel strip runs inside the PVC for its full length, and a barb and a curved gripping arm inside the 6.5 mm deep channel lock onto both faces of the panel. It covers sharp cut edges, protects the panel from knocks and gives a neat finished edge. Choose any length from 14 m to 49 m in one continuous piece, or a full 50 m coil. It is in stock in the UK for same-day dispatch.
At a glance
- Fits: sheet metal, plastic, fibreglass and board edges 1 mm to 1.5 mm thick
- Size: 5.5 mm wide × 8.5 mm high; 2.0 mm opening; 6.5 mm grip depth
- Construction: flexible PVC, 70° Shore A, moulded over a U-shaped steel carrier
- Grip: internal barb and gripping arm hold it on by clamping force alone; it can be taken off and refitted
- Working temperature: −10 °C to +60 °C
- Lengths: 14 m to 49 m in 1 m steps, or a full 50 m coil. The 50 m coil costs less than any length from 39 m up.
Technical drawing

All dimensions are in mm and nominal. The drawing is not to scale. The steel carrier and grip shapes are shown as typical.
Specifications
| Property | Value | Test method / basis |
|---|---|---|
| Profile | Self-gripping U edge trim with steel carrier, internal barb and gripping arm | Manufacturer drawing |
| Overall width | 5.5 mm | Manufacturer drawing |
| Overall height | 8.5 mm | Manufacturer drawing |
| Inside depth (grip depth) | 6.5 mm | Manufacturer drawing |
| Opening at the mouth | 2.0 mm | Manufacturer drawing |
| Panel thickness it fits | 1.0 mm to 1.5 mm | Manufacturer |
| Section thickness | 2.5 mm | Manufacturer figure; measuring point not stated |
| Cover over the panel edge | 2.0 mm | Calculated: 8.5 − 6.5 mm |
| Side wall each side of the opening | 1.75 mm | Calculated: (5.5 − 2.0) ÷ 2 |
| Jacket material | Flexible PVC | Manufacturer |
| Carrier | Steel, U-shaped, full length | Manufacturer |
| Colour | Black | Manufacturer |
| Hardness | 70° Shore A | Manufacturer data; method not stated |
| Density | 1.35 to 1.45 g/cm³ | Manufacturer data; method not stated |
| Tensile strength | More than 11 MPa | Manufacturer data; method not stated |
| Elongation at break | More than 260 % | Manufacturer data; method not stated |
| Minimum working temperature | −10 °C | Manufacturer data |
| Maximum working temperature | +60 °C | Manufacturer data |
| Tear strength | Not stated for this profile | Ask us if you need it |
| Compression set | Not stated for this profile | Ask us if you need it |
| Dimensional tolerance | Not stated; dimensions are nominal | Ask us if you need it |
| Supplied as | One continuous length, 14 m to 50 m | Choose a length above |
Lengths and prices
| Length | Price inc VAT | Per metre |
|---|---|---|
| 14 m | £171.87 | £12.28 |
| 15 m | £184.14 | £12.28 |
| 16 m | £196.41 | £12.28 |
| 17 m | £208.68 | £12.28 |
| 18 m | £220.98 | £12.28 |
| 19 m | £233.25 | £12.28 |
| 20 m | £245.52 | £12.28 |
| 21 m | £257.79 | £12.28 |
| 22 m | £270.06 | £12.28 |
| 23 m | £282.36 | £12.28 |
| 24 m | £294.63 | £12.28 |
| 25 m | £306.90 | £12.28 |
| 26 m | £319.17 | £12.28 |
| 27 m | £331.44 | £12.28 |
| 28 m | £343.74 | £12.28 |
| 29 m | £356.01 | £12.28 |
| 30 m | £368.28 | £12.28 |
| 31 m | £380.55 | £12.28 |
| 32 m | £392.82 | £12.28 |
| 33 m | £405.12 | £12.28 |
| 34 m | £417.39 | £12.28 |
| 35 m | £429.66 | £12.28 |
| 36 m | £441.93 | £12.28 |
| 37 m | £454.20 | £12.28 |
| 38 m | £466.50 | £12.28 |
| 39 m | £478.77 | £12.28 |
| 40 m | £491.04 | £12.28 |
| 41 m | £503.31 | £12.28 |
| 42 m | £515.58 | £12.28 |
| 43 m | £527.88 | £12.28 |
| 44 m | £540.15 | £12.28 |
| 45 m | £552.42 | £12.28 |
| 46 m | £564.69 | £12.28 |
| 47 m | £576.96 | £12.28 |
| 48 m | £589.26 | £12.28 |
| 49 m | £601.53 | £12.28 |
| 50 m full coil | £471.99 | £9.44 |
Materials and compliance
The trim is a flexible PVC jacket moulded over a steel carrier. PVC stands up well to moisture, weather and many everyday chemicals, so the trim can be used indoors and outdoors within its −10 °C to +60 °C range. The manufacturer does not state any food-contact (FDA, EC 1935/2004), drinking-water (WRAS), fire-rating, REACH, RoHS or other product approvals for this profile, so we do not claim any. Do not use it where a certified material is required. Ask us for a certified alternative.
How it fits

- Check the edge. The panel should be 1 mm to 1.5 mm thick. Deburr the edge and make sure it is clean and dry.
- Push on. Start at one end and press the trim fully onto the edge by hand, working along the run.
- Seat it. Tap along the top with a rubber or plastic mallet so the edge reaches the bottom of the channel. You need no adhesive.
- Cut and finish. Cut through the PVC and steel with side cutters, tin snips or a fine hacksaw. Butt the ends tightly together.
Typical uses
- Finishing cut edges on sheet steel and aluminium panels, enclosures and computer or electrical cabinets
- Safety edging on machine guards, brackets and access hatches
- Garage doors, sheds, playground equipment and other outdoor sheet edges
- Fibreglass, plastic and composite panels in marine and vehicle interiors
- Interior side panels, trim panels and side window surrounds
- Protecting sheet edges in storage and transport
FAQ
What thickness of panel does it fit?
It is made for edges 1 mm to 1.5 mm thick, which covers most 1.2 mm sheet steel and aluminium. On thinner material it will not grip firmly. For thicker edges, choose a larger self-grip trim, such as the 12 × 15.5 mm size.
How do I work out what length I need?
Measure the edge thickness with a caliper, then measure the total run in metres and add about 5 % for cutting and corners. Choose the next length up. If you need more than 38 m, buy the full 50 m coil, because it costs less than any length from 39 m up.
Do I need glue?
No. The steel carrier keeps the jaws clamped, and the barb and gripping arm hold the trim on. Because there is no adhesive, you can remove it and fit it again.
Will it go round corners and curves?
Yes. The steel carrier bends, so the trim follows curves and radiused corners. For a sharp 90° external corner, cut a small V-notch in the inside of the trim so it folds neatly without bunching.
How do I cut it?
Because of the steel carrier, a knife alone will not do. Use side cutters, tin snips or a fine-tooth hacksaw, then trim any burr. Butt the ends tightly for a neat joint.
What temperatures can it take?
The manufacturer rates it for −10 °C to +60 °C. It is not suitable for hot engine bays, ovens or places that get very cold. Ask us about a silicone or EPDM trim for those.
Can it be used outdoors?
Yes. PVC resists moisture and weather well, so it suits garage doors, sheds and outdoor equipment within its temperature range.
What is it made of?
A flexible black PVC jacket, 70° Shore A, moulded over a U-shaped steel carrier. Inside the channel there is a barb on one side and a curved gripping arm on the other.
Is it food safe or fire rated?
No approvals are stated for this profile, so do not use it where food-contact, drinking-water or fire certification is needed.
Is it in stock?
Yes. We hold it in stock and supply it as one continuous length cut to the size you choose.
Complete your project
- Self-Grip PVC Edge Trim – 6.5mm x 9.5mm – 50m Coil
- PVC Self-Grip Edge Trim – 12mm x 15.5mm – for thicker panels
- Silicone Self-Grip Edge Trim – 8.9mm x 12.4mm – 1mm to 4mm panels
- EPDM Rubber U Channel – 5.5mm x 8.5mm – fits 3 mm panel
Need help choosing or fitting? Call +44 1282 277786, email sales@industrial-polymers.co.uk or contact our team.
Product details
| SKU | IP-PVCET-5.5X8.5-14M |
|---|---|
| Weight | 2.16 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Self-Grip PVC Edge Trim – 5.5mm x 8.5mm – for 1mm to 1.5mm Panels – 14m to 50m