
Rubber & FoamSKU IP-EPDMD-18X13.75-10M
EPDM D Section Door Seal – 18mm x 13.75mm, Push-On for 2mm Panels – 10m to 29m or 30m Coils
Price shown updates with the option you pick.
A solid black EPDM rubber seal, 18 mm wide by 13.75 mm high, that pushes straight onto a panel edge. A 1.6 mm channel along the bottom grips the panel (rated for 2 mm sheet), and above it a ribbed, hollow rectangular chamber compresses when the door, lid or hatch closes. You get a weather-tight, draught-tight seal and a cushioned, impact-protected edge in one strip, with no adhesive or fixings.
At a glance
- Size: 18 mm wide × 13.75 mm high; 16.5 mm × 2 mm lower leg
- Fits: 2 mm panel edges, via a 1.6 mm push-on channel that grips the sheet
- Material: solid EPDM, 70° ±5° Shore A, with good ozone, UV and weather resistance
- Supplied as: any length from 10 m to 29 m, or 30 m coils (single or multi-coil packs at the lower coil rate)
- Black, cuts cleanly with a sharp knife, and the material is recyclable
- Held in stock in the UK
Typical uses
- Door, hatch and locker seals on caravans, horseboxes, trailers and vehicle bodies
- Restoration seals for doors and windows on older vehicles
- Edge seals on steel or aluminium enclosure doors, cabinets and machine guards
- Bus, rail and marine panels that need a sealed and protected 2 mm edge
Technical drawing

Specification
| Property | Value | Test method / basis |
|---|---|---|
| Overall width | 18 mm | Manufacturer's drawing, nominal |
| Overall height | 13.75 mm | Manufacturer's drawing, nominal |
| Lower leg length (inside the spine) | 16.5 mm | Manufacturer's drawing, nominal |
| Lower leg thickness | 2.0 mm | Manufacturer's drawing, nominal |
| Channel width | 1.6 mm | Manufacturer's drawing, nominal |
| Panel thickness it fits | 2 mm | Manufacturer's fitting data |
| Hollow chamber (approx.) | ≈ 14.2 × 3.9 mm | Scaled from the manufacturer's drawing, not a stated size |
| Material | EPDM (ethylene propylene diene rubber), solid | Manufacturer's data sheet |
| Colour | Black | - |
| Hardness | 70° ±5° Shore A (65–75°) | Manufacturer's data sheet |
| Tensile strength | 10 MPa | Manufacturer's data sheet |
| Elongation at break | 500 % | Manufacturer's data sheet |
| Tear strength | 50 kN/m | Manufacturer's data sheet |
| Compression set | 21 % | 22 h at 70 °C |
| Ozone resistance | No cracks | 72 h at 40 °C, 25 pphm ozone |
| Heat ageing: change in tensile strength | +9 % | 70 h at 70 °C |
| Heat ageing: change in elongation | 0 % | 70 h at 70 °C |
| Service temperature | approx. −40 °C to +100 °C | Typical for EPDM, not tested on this profile |
| Density | approx. 1.2–1.4 g/cm³ | Typical for solid EPDM, not tested on this profile |
| Dimensional tolerance | Not stated by the manufacturer | Extruded profiles are normally made to ISO 3302-1 class E2 |
| Lengths | 10–29 m cut lengths; 30 m coils | - |
Materials and compliance
Made from a general-purpose solid EPDM compound, chosen for its resistance to weather, UV and ozone (no cracking after 72 hours in 25 pphm ozone), so it suits indoor and outdoor use. The manufacturer does not state food-contact, WRAS, flame-retardant or other approvals for this profile, so do not use it where one of those approvals is required. If you need a certified grade, ask us.
How it fits

- Clean the panel edge and remove any burrs, grease or loose paint.
- Start at a hinge-side corner. Push the 1.6 mm channel onto the panel edge until the edge meets the spine. Use a rubber mallet if needed; the channel is slightly narrower than a 2 mm sheet so that it grips.
- Work along the edge without stretching the seal. Stretched rubber shrinks back and leaves gaps at the corners.
- On tight corners, ease the seal round. For a sharp 90° corner, mitre-cut it and bond the joint with a cyanoacrylate (superglue) rubber adhesive.
- Butt-join the two ends at the bottom or hinge side, and allow a few millimetres of extra length so the joint stays closed.
Which length should I choose?
Choose the exact length you need from 10 m to 29 m (£18.18 per metre inc VAT), or a 30 m coil at the lower coil rate (£13.35 per metre inc VAT). From 23 m upwards, a full 30 m coil costs less than a cut length, so it is the better buy. For long runs, multi-coil packs of 60, 90, 120 and 150 m are also available. Measure the full perimeter of the opening and add about 2–3 % for corners and joints.
Frequently asked questions
What panel thickness does it fit?
It is designed for 2 mm sheet. The channel is 1.6 mm wide, so it stretches slightly over a 2 mm edge and holds by grip, with no adhesive. On thinner sheet (around 1.5 mm or less) it will be looser, so run a bead of adhesive in the channel. On sheet thicker than 2 mm it will be difficult to fit.
Which way round does it go?
The channel goes onto the panel edge, so the ribbed hollow chamber sits on the face that the closing door, lid or frame presses against. The chamber compresses to make the seal.
Can I use it outdoors?
Yes. EPDM resists rain, UV and ozone. This compound showed no cracks after a 72-hour ozone test and kept its strength after heat ageing at 70 °C.
What temperatures will it take?
The manufacturer does not give a temperature range for this profile. Solid EPDM is typically used from around −40 °C to +100 °C. For a hot application, talk to us first.
How do I cut and join it?
Use a sharp utility knife or rubber shears, and cut square for butt joints. Cut at 45° if you are mitring a corner. Bond the joints with a cyanoacrylate rubber adhesive.
Is it oil and fuel resistant?
No. EPDM swells in contact with oils, fuels and most solvents. For those, use a nitrile or neoprene profile instead.
Will it suit my vehicle or caravan?
Check three things: the panel edge is 2 mm thick, the space between the panel edge and the closing face is about 13 mm, and an 18 mm wide seal fits along the edge. If you are not sure, send us your measurements or a photo and we will check it for you.
How quickly will it arrive?
It is held in stock and dispatched as shown on this page. Cut lengths are supplied in one continuous piece.
Complete your project
- EPDM Self-Grip Edge Trim – 14.8mm x 14.9mm – Per Metre
- EPDM L Profile Angle Trim – 15.5mm x 16.5mm – Per Metre
- EPDM D Section Door Seal – 12.5mm x 9.5mm
Need a different size, a cut-to-length batch or help choosing? Contact our team: +44 1282 277786 or sales@industrial-polymers.co.uk.
Product details
| SKU | IP-EPDMD-18X13.75-10M |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM D Section Door Seal – 18mm x 13.75mm, Push-On for 2mm Panels – 10m to 29m or 30m Coils