
Rubber & FoamSKU IP-SGT-16X32.9-10M
Self-Grip EPDM Top Seal – 16mm x 32.9mm – Large Sponge Bulb with Fin, Fits 1-3mm Panels – 10m to 100m
Price shown updates with the option you pick.
A push-on EPDM top seal for 1mm to 3mm panel, sheet and flange edges. A steel-cored solid rubber grip clamps the edge with no glue, and a large hollow closed-cell sponge bulb with a sealing fin sits on top to close the gap against a door, hatch or lid. It is 32.9mm high and 16mm wide overall, black, and supplied as one continuous length from 10m to 49m, a full 50m coil, or 100m (two 50m coils). Cut lengths are £11.52 per metre inc VAT; the coil works out at £7.68 per metre.
At a glance
- 32.9mm high x 16mm wide overall: 17mm sponge bulb (2mm wall) on a 13mm-tall grip
- Grip section 14mm wide with an 8mm opening and 3mm side legs
- Fits sheet, panel and flange edges 1mm to 3mm thick
- Solid EPDM grip, 70° Shore A, with a full-length U-shaped steel carrier and internal gripping fins
- Closed-cell EPDM sponge bulb (0.6 g/cm³) with sealing fin; compress it 30% to 40%
- Weather, ozone and UV resistant; -40°C to +70°C in service
- 0.24kg per metre; in stock in the UK; each length up to 50m is one piece with no joins
Technical drawing

Specification
| Property | Value | Test method / note |
|---|---|---|
| Overall height | 32.9mm | Bottom of grip to tip of fin |
| Height without fin | 30mm | Bottom of grip to top of bulb |
| Overall width | 16mm | Across the sponge bulb |
| Bulb height | 17mm | Top of grip to top of bulb |
| Bulb wall thickness | 2mm | Sponge wall |
| Grip height | 13mm | Solid section with steel carrier |
| Grip section width | 14mm | Outside of the solid U |
| Channel opening | 8mm | Between the legs, before the internal fins |
| Leg thickness | 3mm each | Each side of the grip |
| Panel thickness it fits | 1mm to 3mm | - |
| Weight | 0.24 kg/m | - |
| Construction | Solid EPDM grip, closed-cell EPDM sponge bulb and fin, steel carrier | Co-extruded |
| Solid EPDM (grip section) | ||
| Hardness | 70-71° Shore A (requirement 70° ± 5°) | ISO 7619-1 |
| Tensile strength | 7.8 MPa (requirement ≥ 7.5 MPa) | ISO 37 |
| Elongation at break | 340% (requirement ≥ 300%) | ISO 37 |
| Tear resistance | 22.18 N/mm (requirement ≥ 8 N/mm) | ISO 34-1 |
| Compression set, 22h at 100°C | 23.12% (requirement 35% max) | ISO 815 |
| Low-temperature ageing, 168h at -10°C | Hardness change +4° (limit +10°) | DIN 53505 |
| Ozone resistance, 72h at 40°C, 50 pphm | No cracking | ISO 1431-1 A |
| UV resistance | No migration | ASTM D1148 |
| Brittleness point, 24h at -40°C | No cracking | ISO 812 |
| Working temperature (solid grade) | -40°C to +120°C | - |
| EPDM sponge (bulb and fin) | ||
| Density | 0.6 g/cm³ | ISO 2781 |
| Tensile strength | 2.8 MPa | ISO 37 |
| Elongation at break | 140% | ISO 37 |
| Compression deflection | 42 kPa | ASTM D1056 |
| Water absorption | 0.98% | ASTM D1056 |
| Ozone resistance, 72h at 40°C, 50 pphm | No cracking | ISO 1431-1 A |
| Thermal conductivity | 0.15 W/m·K | ASTM C518 |
| Recovery after ageing | 82% | - |
| Working temperature (sponge) | -40°C to +70°C | Sets the limit for the whole seal |
| In use | ||
| Recommended bulb compression | 30% to 40%; 50% absolute maximum | Over-compression causes permanent set |
| Service temperature (whole seal) | -40°C to +70°C | Limited by the sponge |
| Colour | Black | - |
| Supplied as | One length: 10m to 49m in 1m steps; 50m full coil; 100m as two 50m coils | - |
All values are from the manufacturer's data sheet for this profile. Dimensional tolerances are not published; if your design depends on a tight fit, ask us before ordering.
Materials and compliance
Made from EPDM, a synthetic rubber chosen for outdoor sealing because it resists weathering, ozone, UV and water, with a closed-cell EPDM sponge bulb that hardly absorbs water (0.98%). The manufacturer does not state any food-contact, drinking-water, fire or other product approvals for this seal, so none are claimed here. Ask us if you need a seal with a specific approval.
How it fits

Typical uses
- Doors, hatches and lockers on vans, trailers, caravans, buses, rail vehicles and boats
- Lids and doors on steel cabinets, electrical enclosures and outdoor equipment housings
- Access panels, side windows and roof panels on vehicles and machinery
- Covering a sharp 1mm to 3mm edge while sealing a wide gap against a closing face
Which top seal do I need?
| Self-grip top seal | Choose it when |
|---|---|
| 16mm x 32.9mm (this item) | Your edge is 1mm to 3mm and the gap needs a large 17mm sponge bulb |
| 14mm x 32mm | A similar height, but your edge is thin (0.5mm to 1.5mm) |
| 15mm x 30.5mm | Your edge is 1.6mm to 3mm and a slightly smaller bulb will do |
| 12mm x 21mm | The gap is smaller and you want a lower-profile seal on a 1.6mm to 3mm edge |
How much do I need?
Add up every edge to be sealed and allow 5% to 10% for corners and trimming. Example: a cabinet door opening 1.8m x 0.6m has a 4.8m perimeter, about 5.2m with allowance; two such doors need 10.4m, so choose 11m. The 50m coil (£384.00) costs less than any cut length from 34m upwards, so choose the coil if you need more than 33m. For 100m, the two-coil option works out at £7.26 per metre.
Fitting
- Clean the edge and remove burrs.
- Start on a straight run and press the grip fully onto the edge by hand; tap with a rubber or soft-faced mallet to seat it.
- Ease it round corners rather than cutting; the steel carrier holds the shape. Do not stretch it as you fit it.
- Set the closed gap so the bulb is squeezed 30% to 40% (about 5mm to 7mm of the 17mm bulb), never more than 50%.
- Cut with heavy-duty snips or a fine hacksaw (it has a steel core) and butt the ends tightly.
Questions
Do I need glue to fit it?
No. The steel carrier and internal gripping fins clamp a 1mm to 3mm edge on their own.
Will it fit a 0.5mm or 4mm panel?
No. Below 1mm the fins will not hold firmly; for thin sheet choose the 14mm x 32mm top seal. Above 3mm it will not push fully on.
What gap will it seal?
The 17mm sponge bulb works best squeezed 30% to 40%, so set the closed door or lid to press it by roughly 5mm to 7mm. Going past 50% gives the sponge a permanent set.
Can it go round corners?
Yes. It bends round radiused corners and holds the shape thanks to the steel carrier. On very tight corners, make a small notch in the grip on the inside of the bend so it lies flat.
How do I cut and join it?
Cut through the rubber and steel carrier with heavy-duty snips or a fine hacksaw. Butt the two ends together tightly; a dab of rubber-compatible sealant at the joint keeps water out.
Is it suitable outdoors and in the cold?
Yes. Both the solid and sponge EPDM passed the manufacturer's ozone test with no cracking, the solid grade passed a -40°C brittleness test, and the whole seal is rated -40°C to +70°C.
Is it resistant to chemicals?
The manufacturer rates it as resistant to most household chemicals and detergents. As is typical for EPDM (not tested on this profile), it is not suited to continuous contact with oils, fuels or petrol.
Is it one piece?
Yes. Lengths up to 50m are cut as one continuous piece. The 100m option is supplied as two 50m coils.
Need help choosing? Call +44 1282 277786 or email sales@industrial-polymers.co.uk.
Product details
| SKU | IP-SGT-16X32.9-10M |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Self-Grip EPDM Top Seal – 16mm x 32.9mm – Large Sponge Bulb with Fin, Fits 1-3mm Panels – 10m to 100m