
Rubber & FoamSKU IP-IPSGT-17X31X5-10
EPDM Self-Grip Top Seal – 17mm x 31mm for 5mm Panels – 10m to 25m Lengths
Price shown updates with the option you pick.
This EPDM self-grip top seal 17mm x 31mm pushes onto 5mm thick panel edges, sealing the tops of hatches, enclosure doors and roof panels with a hollow sponge bulb while covering the sharp sheet edge. Choose the length you need: each option is one continuous piece from 10m to 25m, priced for that whole length.
At a glance
- 17mm wide x 31mm high overall, with a hollow sponge bulb on top
- Grips 5mm thick panel edges - for thicker sheet than most top seals
- Solid EPDM grip channel with an embedded steel carrier - no adhesive needed
- Weather, UV and ozone resistant EPDM rubber
- Works from -40°C to +80°C
- Supplied as one continuous length, 10m to 25m in 1m steps
Typical uses
- Sealing the closing edge of access hatches and inspection covers
- Weatherproofing enclosure doors and roof panels
- Door and window seals on vans, buses, trains and trailers
- Marine lockers and deck hatches
- Safe edging for raw sheet metal on cabinets and machine guards
Which one do I need?
| Top seal | Choose it when |
| 17mm x 31mm (this seal) | 5mm panels; the 31mm height suits the gap you need to close |
| 15mm x 30.5mm | Thinner 1.6mm to 3mm panels with a similar seal height |
| 14mm x 32mm | Thin 0.5mm to 1.5mm sheet |
For the closed gap, aim for the bulb to compress by 30% to 40%. Check your panel thickness first - the grip only holds properly on the thickness it is made for.
Technical drawing
Specification
| Overall size | 17mm wide x 31mm high |
| Panel thickness | 5mm |
| Material | Solid EPDM grip, sponge EPDM bulb, steel carrier |
| Colour | Black |
| Hardness | 67° to 82° Shore A (solid section) |
| Operating temperature | -40°C to +80°C |
| Maximum compression | 40% (30% to 40% recommended) |
| Weight | About 0.17kg per metre |
| Unit of sale | One continuous length; choose 10m to 25m |
How much do I need?
Add up every edge the seal will run along. A hatch of 1.5m x 1m has a perimeter of 1.5 + 1 + 1.5 + 1 = 5m; two such hatches need 10m, so the 11m length gives you a little spare for trimming. The 25m option is a full coil and is priced lower than the 20m to 24m cut lengths, so it is worth choosing if you need more than about 19m.
Fitting tips
- Clean the edge and file off burrs before fitting.
- Press the grip channel on by hand, working from one end, then tap along it with a rubber mallet to seat it fully.
- No glue is needed - the steel carrier holds it.
- Cut squarely with heavy-duty snips through the carrier and butt the ends tightly at the joint.
- Keep bulb compression below 50% or the sponge can take a permanent set.
Complete your project
- EPDM Self-Grip Top Seal – 15mm x 30.5mm – 11m to 25m Lengths
- EPDM Self-Grip Top Seal – 22.5mm High – 11m to 25m Lengths
- EPDM Self-Grip Top Seal – 14mm x 32mm – Fits 0.5mm to 1.5mm Panels
Questions
Is this top seal sold per metre?
No. Each option is one continuous length from 10m to 25m at the price shown for that length, so a whole opening can be sealed with a single joint.
Do I need adhesive to fit it?
No. The steel carrier in the grip channel holds it firmly on 5mm panels.
Will it fit a 3mm panel?
No - it is made for 5mm edges. For 1.6mm to 3mm sheet choose the 15mm x 30.5mm top seal.
Can this EPDM seal be used outdoors?
Yes. EPDM resists weather, UV and moisture and works from -40°C to +80°C.
What if I compress the bulb too much?
Beyond 50% the sponge can deform permanently and stop sealing, so set the closed gap for 30% to 40% compression.
Need help choosing the right edge seal? Contact our team for advice.
Product details
| SKU | IP-IPSGT-17X31X5-10 |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM Self-Grip Top Seal – 17mm x 31mm for 5mm Panels – 10m to 25m Lengths