
Rubber & FoamSKU IP-EPDMC-14.5X7.5-STD
EPDM Sponge Crown Strip – 14.5mm x 7.5mm, Self-Adhesive – 50m Coil
The tallest crown strip in the range: black EPDM sponge, 14.5 mm wide and 7.5 mm high, with a peel-and-stick adhesive base. One continuous 50 m coil. Five rounded crowns press flat when a hatch, door or lid closes on them, giving five sealing lines across the face, while the extra height soaks up knocks and copes with uneven or wider gaps than the low-profile strips.
At a glance
- Size: 14.5 mm wide × 7.5 mm high; 6.5 mm at the groove floor (1 mm deep grooves)
- Face: five crowns and four scalloped grooves for multiple sealing lines
- Fixing: factory-applied adhesive backing with a peel-off liner; sticks to clean metal, plastic, wood and rubber
- Material: skinned, solid expanded (sponge) EPDM, very soft at 40° Shore OO, non-marking
- Outdoors: rated excellent for ozone, weather and UV; flexible at -40 °C
- Coil: 50 m continuous length, black, 40 g/m, about £4.71 per metre
- Stock: held in stock in the UK and dispatched from stock
Typical uses
- Weather and dust seals on hatches, access panels, vehicle and trailer doors, and boat lockers
- Lid seals on equipment cases, enclosures and cabinets with a 5 to 6 mm closed gap
- Closure and glazing seals where the mating face is uneven
- Shock-absorbing bump strip on tailgates, drop-down sides, shelving and machinery guards
- Expansion-joint and anti-vibration packing between panels and frames
Technical drawing

Specifications
| Property | Value | Test method / basis |
|---|---|---|
| Profile type | Solid crown strip: five rounded crowns separated by four scalloped grooves, on a flat self-adhesive base | Manufacturer's profile drawing |
| Overall width (across the base) | 14.5 mm | Nominal; tolerance BS 3734 Class E3 |
| Overall height (base to top of crowns) | 7.5 mm | Nominal; tolerance BS 3734 Class E3 |
| Height at the groove floor | 6.5 mm | Manufacturer's profile drawing |
| Groove depth | 1.0 mm (7.5 mm less 6.5 mm) | Derived from the manufacturer's dimensions |
| Crowns / grooves across the face | 5 crowns, 4 grooves; spacing not dimensioned (about 3.4 mm pitch on the maker's drawing) | Manufacturer's profile drawing (shape only) |
| Minimum landing width | 14.5 mm flat surface to stick to | Equal to the base width |
| Fixing | Factory-applied adhesive backing with peel-off liner | Adhesive type and thickness not stated by the manufacturer |
| Material | Expanded (sponge) EPDM, skinned surface | Manufacturer datasheet |
| Colour | Black | - |
| Hardness | 40° Shore OO | Shore OO durometer scale (for soft foams); test standard not stated |
| Density | 0.5 to 0.9 g/cm³ | Manufacturer datasheet; method not stated |
| Weight | 40 g per metre (about 2.0 kg per 50 m coil) | Manufacturer figure (product page and datasheet agree) |
| Water absorption | 5% maximum | Manufacturer datasheet; method not stated |
| Compression set | 25% maximum (datasheet, 24 h recovery) · 50% (product page, 22 h) | Manufacturer figures; test temperature and standard not stated. The two sources differ, so plan on the higher figure |
| Heat ageing | ±30% change after 7 days at 70 °C | Manufacturer datasheet; property measured not stated |
| Low-temperature flexibility | Pass at -40 °C | Manufacturer datasheet |
| Ozone resistance | Excellent | Manufacturer rating |
| Weather resistance | Excellent | Manufacturer rating |
| UV light resistance | Excellent | Manufacturer rating |
| Mould growth resistance | Very good | Manufacturer rating |
| Service temperature range | Not stated for this profile. About -40 °C to +100 °C (typical for EPDM sponge, not tested on this profile) | Tested points stated: flexible at -40 °C, aged at +70 °C |
| Tensile strength, elongation at break, tear strength | Not stated for this profile | Ask us if you need them |
| Dimensional tolerance | BS 3734 Class E3 (extruded sponge); sizes are approximate because the section is flexible | BS 3734 |
| Supplied length | 50 m continuous coil | - |
| Price per metre | About £4.71/m inc VAT (£235.41 per 50 m coil) | - |
The manufacturer gives two compression-set figures for this part (25% maximum on the datasheet, 50% on the product page); both are shown above. Sponge sections are flexible, so treat all sizes as nominal.
Materials and compliance
Skinned expanded (sponge) EPDM with a factory-applied adhesive backing. The manufacturer describes the profile as non-marking, air and watertight, and resistant to ozone, weather, heat, steam, ketones and dilute acids and alkalis, with good electrical insulation. Like all EPDM it is not suited to oils, fuels or solvents.
The manufacturer does not state any food-contact (FDA, EC 1935/2004), drinking-water (WRAS), REACH, RoHS or fire-rating approval for this profile, so we do not claim any. If your job needs a certified material, ask us before you order.
How it fits

- Measure the closed gap. It should be smaller than 7.5 mm so the crowns are squeezed. About 5 to 6 mm (20 to 33% squeeze) is a good starting point; this is our guidance, not a manufacturer figure.
- Check the landing. The flat face you stick to should be at least 14.5 mm wide.
- Clean and dry. Wipe with isopropyl alcohol and let it dry. Fit above about 10 °C for the best bond.
- Peel and press. Peel the liner a short way at a time and press the base down firmly along its length. Do not stretch the strip or it will shrink back.
- Corners and joins. Ease it round gentle corners; for sharp corners cut and butt the ends tightly, or mitre them. Put joins where water will not sit.
Which size do I need?
| Profile | Size (W × H) | Best for a closed gap of | Supplied as |
|---|---|---|---|
| EPDM sponge crown strip | 10 × 5 mm | about 3 to 4 mm | 100 m coil, self-adhesive |
| EPDM sponge crown strip | 15 × 4 mm | about 2.5 to 3 mm | 100 m coil, self-adhesive |
| EPDM sponge crown strip (this item) | 14.5 × 7.5 mm | about 5 to 6 mm | 50 m coil, self-adhesive |
| EPDM sponge D section (hollow) | 12 × 10 mm | larger gaps, lower closing force | 75 m coil |
Gap ranges are our guidance for 20 to 35% squeeze, not manufacturer figures.
Data sheet
Download the technical data sheet (PDF): drawing, full specification and compliance
Questions
Is the price per metre or per coil?
Per coil. One unit is a complete 50 m continuous coil, which works out at about £4.71 per metre.
What gap will it seal?
Closed gaps below its 7.5 mm height; aim for about 5 to 6 mm. For gaps of 3 to 4 mm the 10 × 5 mm crown strip is a better fit.
How do I fit it?
Clean the surface with isopropyl alcohol, peel back the liner a little at a time and press the flat base down firmly onto a landing at least 14.5 mm wide. Do not stretch it as you go.
How do I cut and join it?
A sharp craft knife or scissors gives a clean square end. Butt the ends tightly together; for a fully sealed join, bond the ends with a rubber-compatible instant adhesive.
Can I use it outdoors?
Yes. The manufacturer rates its ozone, weather and UV resistance as excellent, and it absorbs no more than 5% water.
What temperatures can it take?
The manufacturer has tested it as flexible at -40 °C and heat-aged it at +70 °C, but does not state a full working range. EPDM sponge typically works from about -40 °C to +100 °C (typical for EPDM sponge, not tested on this profile).
Why five crowns rather than a flat strip?
Each crown makes its own line of contact, so the strip seals with less closing force than a flat foam block of the same size, and the grooves give the sponge room to spread as it is squeezed.
Can I use it as a bump or impact strip?
Yes. At 7.5 mm it is the tallest crown strip we stock, and the soft 40° Shore OO sponge cushions knocks on tailgates, guards and shelving edges.
Will it mark painted surfaces?
The manufacturer states it is non-marking.
Will it stand up to oil or fuel?
No. EPDM handles water, steam, weather and dilute acids and alkalis well but swells in oils, fuels and most solvents. Ask us for a neoprene or nitrile alternative.
Is it food-safe or WRAS approved?
No approvals are stated for this profile, so do not use it where certified food-contact or drinking-water material is required.
Delivery and help
Held in stock and dispatched from the UK. Trade and quantity orders welcome. Not sure it is the right profile? Call +44 1282 277786 or email sales@industrial-polymers.co.uk and we will check it for you.
Product details
| SKU | IP-EPDMC-14.5X7.5-STD |
|---|---|
| Weight | 4.41 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM Sponge Crown Strip – 14.5mm x 7.5mm, Self-Adhesive – 50m Coil