
Rubber & FoamSKU IP-EPDMC-15X4-STD
EPDM Sponge Crown Strip – 15mm x 4mm, Self-Adhesive – 100m Coil
A wide, low-profile black EPDM sponge seal: 15 mm across, only 4 mm high, with a peel-and-stick adhesive base. One continuous 100 m coil. Five rounded crowns run along the face. When a door, hatch, window or lid closes on them they press flat, giving five sealing lines across a broad 15 mm band. Use it where there is little depth for a seal but a wide landing, or as a soft, discreet bump strip on panel edges.
At a glance
- Size: 15 mm wide × 4 mm high; five crowns, 2 mm end crowns
- Fixing: factory-applied adhesive backing with a peel-off liner; sticks to clean metal, glass, plastic, wood and rubber
- Material: solid expanded (sponge) EPDM, very soft at 40° Shore OO, non-marking
- Outdoors: rated excellent for ozone, weather and UV; flexible at -40 °C
- Coil: 100 m continuous length, black, about £3.33 per metre
- Stock: held in stock in the UK and dispatched from stock
Typical uses
- Low-profile door and window seals where the frame gives a wide, shallow landing
- Lid and door seals on electrical enclosures, control boxes, equipment cases and cabinets
- Weather strips on vehicles, trailers, caravans, horseboxes and boats
- Glazing, closure and expansion-joint packing strips
- Anti-rattle and vibration pads between panels, covers and housings
- Soft, discreet impact protection on edges, shelving and display fittings
Technical drawing

Specifications
| Property | Value | Test method / basis |
|---|---|---|
| Profile type | Solid crown strip: five rounded crowns separated by four shallow grooves, on a flat self-adhesive base | Manufacturer's profile drawing |
| Overall width (across the base) | 15.0 mm | Nominal; tolerance BS 3734 Class E3 |
| Overall height (base to top of crowns) | 4.0 mm | Nominal; tolerance BS 3734 Class E3 |
| End crown width (each edge) | 2.0 mm | Manufacturer's profile drawing |
| Number of crowns | 5 | Manufacturer's profile drawing |
| Groove depth | Not stated (shallow, about 1 mm on the drawing) | Manufacturer's profile drawing (shape only) |
| Minimum landing width | 15 mm flat face | Our guidance, from the base width |
| Fixing | Factory-applied adhesive backing with peel-off liner | Adhesive type and thickness not stated by the manufacturer |
| Material | Expanded (sponge) EPDM | Manufacturer datasheet |
| Colour | Black | - |
| Hardness | 40° Shore OO | Shore OO durometer scale (for soft foams); test standard not stated |
| Density | 0.5 to 0.9 g/cm³ | Manufacturer datasheet; method not stated |
| Weight | 20 g/m (datasheet) to 23 g/m (product data): about 2.0 to 2.3 kg per 100 m coil | Manufacturer figures; the sources differ slightly |
| Water absorption | 5% maximum | Manufacturer datasheet; method not stated |
| Compression set | 25% maximum (datasheet, 24 h recovery) · 50% (product data, 22 h) | Manufacturer figures; test temperature and standard not stated. The two sources differ, so plan on the higher figure |
| Heat ageing | ±30% change after 7 days at 70 °C | Manufacturer datasheet; property measured not stated |
| Low-temperature flexibility | Pass at -40 °C | Manufacturer datasheet |
| Ozone resistance | Excellent | Manufacturer rating |
| Weather resistance | Excellent | Manufacturer rating |
| UV light resistance | Excellent | Manufacturer rating |
| Mould growth resistance | Very good | Manufacturer rating |
| Service temperature range | Not stated for this profile. About -40 °C to +100 °C (typical for EPDM sponge, not tested on this profile) | Tested points stated: flexible at -40 °C, aged at +70 °C |
| Tensile strength, elongation at break, tear strength | Not stated for this profile | Ask us if you need them |
| Dimensional tolerance | BS 3734 Class E3 (extruded sponge) | BS 3734 |
| Supplied length | 100 m continuous coil | - |
| Price per metre | About £3.33/m inc VAT (£333.00 per 100 m coil) | - |
The manufacturer gives two weights (23 g/m and 0.02 kg/m) and two compression-set figures for this part; both are shown above. Sponge sections are flexible, so treat all sizes as nominal.
Materials and compliance
Expanded (sponge) EPDM with a factory-applied adhesive backing. The manufacturer describes the profile as non-marking and air and watertight, and EPDM resists ozone, weather, heat, steam, ketones and dilute acids and alkalis. Like all EPDM it is not suited to oils, fuels or solvents.
The manufacturer does not state any food-contact (FDA, EC 1935/2004), drinking-water (WRAS), REACH, RoHS or fire-rating approval for this profile, so we do not claim any. If your job needs a certified material, ask us before you order.
How it fits

- Measure the closed gap. It must be smaller than 4 mm so the crowns are squeezed. About 2.5 to 3.5 mm (roughly 15 to 40% squeeze) is a good starting point; this is our guidance, not a manufacturer figure.
- Check the landing. The flat face you stick to should be at least 15 mm wide, and the closing face should cover the full width.
- Clean and dry. Wipe with isopropyl alcohol and let it dry. Fit above about 10 °C for the best bond.
- Peel and press. Peel the liner a short way at a time and press the base down firmly along its length. Do not stretch the strip or it will shrink back.
- Corners and joins. Ease it round gentle corners; for sharp corners cut and butt the ends tightly, or mitre them. Put joins where water will not sit.
Which size do I need?
| Profile | Size (W × H) | Supplied as |
|---|---|---|
| EPDM sponge crown strip (this item) | 15 × 4 mm | 100 m coil, self-adhesive |
| EPDM sponge crown strip | 10 × 5 mm | 100 m coil, self-adhesive |
| EPDM sponge crown strip | 14.5 × 7.5 mm | 50 m coil |
| EPDM sponge P-section seal (hollow bulb) | 10 × 7 mm | 100 m coil, self-adhesive |
| EPDM sponge D section (hollow) | 8 × 10 mm | 50 m coil, self-adhesive |
Data sheet
Download the technical data sheet (PDF): drawing, full specification and compliance
Questions
Is the price per metre or per coil?
Per coil. One unit is a complete 100 m continuous coil, which works out at about £3.33 per metre.
What gap will it seal?
Closed gaps below its 4 mm height; aim for about 2.5 to 3.5 mm. For gaps around 3 to 4 mm on a narrower landing choose the 10 × 5 mm crown strip; for 5 to 7 mm the 14.5 × 7.5 mm crown strip; for 6 to 8 mm the hollow 8 × 10 mm D section.
How do I fit it?
Clean the surface with isopropyl alcohol, peel back the liner a little at a time and press the flat base down firmly. Do not stretch it as you go.
How do I cut and join it?
A sharp craft knife or scissors gives a clean square end. Butt the ends tightly together; for a fully sealed join, bond the ends with a rubber-compatible instant adhesive.
Can I use it outdoors?
Yes. The manufacturer rates its ozone, weather and UV resistance as excellent, and it absorbs no more than 5% water.
What temperatures can it take?
The manufacturer has tested it as flexible at -40 °C and heat-aged it at +70 °C, but does not state a full working range. EPDM sponge typically works from about -40 °C to +100 °C (typical for EPDM sponge, not tested on this profile).
Why crowns rather than a flat foam tape?
Each of the five crowns makes its own line of contact, so the strip seals with less closing force than a flat tape of the same size, and the grooves give the sponge room to spread as it is squeezed. The wide face also forgives a door that does not close in exactly the same place each time.
Will it mark painted surfaces?
The manufacturer states it is non-marking.
Will it stand up to oil or fuel?
No. EPDM handles water, steam, weather and dilute acids and alkalis well but swells in oils, fuels and most solvents. Ask us for a neoprene or nitrile alternative.
Is it food-safe or WRAS approved?
No approvals are stated for this profile, so do not use it where certified food-contact or drinking-water material is required.
Delivery and help
Held in stock and dispatched from the UK. Trade and quantity orders welcome. Not sure it is the right profile? Call +44 1282 277786 or email sales@industrial-polymers.co.uk and we will check it for you.
Product details
| SKU | IP-EPDMC-15X4-STD |
|---|---|
| Weight | 5.07 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM Sponge Crown Strip – 15mm x 4mm, Self-Adhesive – 100m Coil