
Rubber & FoamSKU IP-EPDMS-12X10-STD
EPDM Sponge D Section – 12mm x 10mm Self-Adhesive – 75m Coil
A soft, hollow D-section seal in black EPDM sponge, 12 mm wide and 10 mm high, with a peel-and-stick adhesive base. One continuous 75 m coil. The domed crown folds into its 8 × 6 mm hollow core when a door, lid or hatch closes on it, so it fills uneven gaps with very little closing force and doubles as a soft bump strip for light to medium knocks.
At a glance
- Size: 12 mm wide × 10 mm high, with an 8 mm × 6 mm hollow core and 2 mm walls
- Fixing: factory-applied adhesive backing with a peel-off liner; no channel, clips or glue needed
- Material: expanded (sponge) EPDM, very soft at 40° Shore OO
- Outdoors: rated excellent for ozone, weather and UV; flexible at -40 °C; 5% maximum water absorption
- Coil: 75 m continuous length, black, about £6.09 per metre
- Stock: held in stock in the UK and dispatched from stock
Typical uses
- Door and lid seals on electrical enclosures, control cabinets, kiosks and switchgear
- Hatch, locker, access panel and inspection door seals on vehicles, trailers, horseboxes, caravans and boats
- Draught and weather strips on sheds, outbuildings, light doors and glazed closures
- Soft bump and impact strip on panel edges, tailboards, shelving and equipment
- Cable protection: small cables can be run through the 8 × 6 mm hollow core
Technical drawing

Specifications
| Property | Value | Test method / basis |
|---|---|---|
| Profile type | Hollow D section on a flat base, self-adhesive | Manufacturer's profile drawing |
| Overall width (across the base) | 12.0 mm | Nominal; tolerance BS 3734 Class E3 |
| Overall height (base to crown) | 10.0 mm | Nominal; tolerance BS 3734 Class E3 |
| Hollow core (width × height) | 8.0 mm × 6.0 mm | Manufacturer's profile drawing and product description |
| Crown wall thickness | 2.0 mm | Manufacturer's profile drawing |
| Side wall thickness | 2.0 mm | Worked out from 12 mm width and 8 mm core; not separately stated |
| Base thickness under the core | 2.0 mm | Worked out from 10 mm height, 6 mm core and 2 mm crown; not separately stated |
| Minimum landing width | 12 mm flat surface | From the 12 mm base width |
| Fixing | Factory-applied adhesive backing with peel-off liner | Adhesive type and thickness not stated by the manufacturer |
| Material | Expanded (sponge) EPDM | Manufacturer datasheet |
| Colour | Black | - |
| Hardness | 40° Shore OO | Shore OO durometer scale (for soft foams); test standard not stated |
| Density | 0.5 to 0.9 g/cm³ | Manufacturer datasheet; method not stated |
| Weight | 40 g/m (datasheet) to 75 g/m (product page): about 3.0 to 5.6 kg per 75 m coil | Manufacturer figures; the two sources differ |
| Water absorption | 5% maximum | Manufacturer datasheet; method not stated |
| Compression set | 25% maximum (datasheet, 24 h recovery) · 50% (product page, 22 h) | Manufacturer figures; test temperature and standard not stated. The two sources differ, so plan on the higher figure |
| Heat ageing | ±30% change after 7 days at 70 °C | Manufacturer datasheet; property measured not stated |
| Low-temperature flexibility | Pass at -40 °C | Manufacturer datasheet |
| Ozone resistance | Excellent | Manufacturer rating |
| Weather resistance | Excellent | Manufacturer rating |
| UV light resistance | Excellent | Manufacturer rating |
| Mould growth resistance | Very good | Manufacturer rating |
| Service temperature range | Not stated for this profile. Typical for EPDM sponge: about -40 °C to +100 °C (typical for EPDM sponge, not tested on this profile) | Tested points stated: flexible at -40 °C, aged at +70 °C |
| Tensile strength, elongation at break, tear strength | Not stated for this profile | Ask us if you need them |
| Dimensional tolerance | BS 3734 Class E3 (extruded sponge) | BS 3734 |
| Supplied length | 75 m continuous coil | - |
| Price per metre | About £6.09/m inc VAT (£456.63 per 75 m coil) | - |
Sponge sections are soft and flexible, so the manufacturer rounds sizes to the nearest whole millimetre. Treat all sizes as nominal.
Materials and compliance
Expanded (sponge) EPDM with a factory-applied adhesive backing. The manufacturer describes the material as air and watertight, with good resistance to heat, ozone, weather, steam and polar substances, ketones and dilute acids and alkalis, and good electrical insulation. Like all EPDM it is not suited to oils, fuels or most solvents.
The manufacturer does not state any food-contact (FDA, EC 1935/2004), drinking-water (WRAS), REACH, RoHS or fire-rating approval for this profile, so we do not claim any. If your job needs a certified material, ask us before you order.
How it fits

- Measure the closed gap. It should be smaller than 10 mm so the D is squeezed. Around 6 to 8 mm (20 to 40% squeeze) is a good starting point; this is our guidance, not a manufacturer figure.
- Check the landing. The flat face you stick to should be at least 12 mm wide.
- Clean and dry. Wipe with isopropyl alcohol and let it dry. Fit above about 10 °C for the best bond.
- Peel and press. Peel the liner a short way at a time and press the base down firmly along its length. Do not stretch the strip or it will shrink back.
- Corners and joins. Ease it round gentle corners; for sharp corners cut and butt the ends tightly, or mitre them. Put joins where water will not sit.
Which size do I need?
| Profile | Size (W × H) | Supplied as |
|---|---|---|
| EPDM sponge D section | 8 × 10 mm | 50 m coil, self-adhesive |
| EPDM sponge D section | 10 × 8 mm | Per metre or 100 m coil |
| EPDM sponge D section (this item) | 12 × 10 mm | 75 m coil, self-adhesive |
| EPDM sponge D section | 12.5 × 12.5 mm | 25 m coil, self-adhesive |
Data sheet
Download the technical data sheet (PDF): drawing, full specification and compliance
Questions
Is the price per metre or per coil?
Per coil. One unit is a complete 75 m continuous coil, which works out at about £6.09 per metre.
What gap will it seal?
Any closed gap below its 10 mm height. Aim for roughly 6 to 8 mm closed. For gaps of about 5 to 7 mm the 8 × 10 mm or 10 × 8 mm sections are easier to close; for slightly larger gaps choose the 12.5 × 12.5 mm section.
How do I fit it?
Clean the surface with isopropyl alcohol, peel back the liner a little at a time and press the flat 12 mm base down firmly. Do not stretch it as you go.
How do I cut and join it?
A sharp craft knife or scissors gives a clean square end. Butt the ends tightly together; for a fully sealed join, bond the ends with a rubber-compatible instant adhesive.
Can I use it outdoors?
Yes. The manufacturer rates its ozone, weather and UV resistance as excellent, and it absorbs no more than 5% water.
What temperatures can it take?
The manufacturer has tested it as flexible at -40 °C and heat-aged it at +70 °C, but does not state a full working range. EPDM sponge typically works from about -40 °C to +100 °C (typical for EPDM sponge, not tested on this profile).
Will it stand up to oil or fuel?
No. EPDM handles water, steam, weather and dilute acids and alkalis well but swells in oils, fuels and most solvents. Ask us for a neoprene or nitrile alternative.
Is it food-safe or WRAS approved?
No approvals are stated for this profile, so do not use it where certified food-contact or drinking-water material is required.
Can I run a cable through the hollow?
Yes. Small cables can be threaded through the 8 × 6 mm core for protection against weather and knocks; leave the core empty if you need the full sealing squeeze.
Delivery and help
Held in stock and dispatched from the UK. Trade and quantity orders welcome. Not sure it is the right profile? Call +44 1282 277786 or email sales@industrial-polymers.co.uk and we will check it for you.
Product details
| SKU | IP-EPDMS-12X10-STD |
|---|---|
| Weight | 12.57 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM Sponge D Section – 12mm x 10mm Self-Adhesive – 75m Coil