
Rubber & FoamSKU IP-EPDMS-10X8-15M
EPDM Sponge D Section – 10mm x 8mm – Cut Length or 100m Coil
Price shown updates with the option you pick.
A soft, hollow D-section seal in black EPDM sponge, 10 mm wide and 8 mm high, with a flat 10 mm base. Cut to any whole length from 15 m to 99 m in one continuous piece, or buy a full 100 m coil. The rounded crown squeezes down into its 4 × 5.2 mm hollow core as a door, lid or hatch closes, so it seals uneven gaps with little closing force and also works as a soft edge or light bump strip.
At a glance
- Size: 10 mm wide × 8 mm high, with a 4 mm × 5.2 mm hollow core
- Material: expanded (sponge) EPDM, very soft at 40° Shore OO
- Fixing: plain flat base: bond it with a contact adhesive suited to EPDM sponge
- Outdoors: rated excellent for ozone, weather and UV; flexible at -40 °C
- Lengths: 15 m to 99 m at £11.25 per metre, or a 100 m coil at £900.00 (£9.00 per metre)
- Stock: held in stock in the UK and dispatched from stock
Typical uses
- Door and lid seals on electrical enclosures, control cabinets and switchgear
- Hatch, access panel and inspection door seals in construction, vehicles and trailers
- Glazing, closure and weather strips
- Soft edging and light impact protection on panels, shelving and equipment
- Gaskets and small expansion-joint fillers
- Protecting thin cables: they can run through the hollow core
Technical drawing

Specifications
| Property | Value | Test method / basis |
|---|---|---|
| Profile type | Hollow D section on a flat, plain base | Manufacturer's profile drawing |
| Overall width (across the base) | 10.0 mm | Nominal; tolerance BS 3734 Class E3 |
| Overall height (base to crown) | 8.0 mm | Nominal; tolerance BS 3734 Class E3 |
| Hollow core (width × height) | 4.0 mm × 5.2 mm | Manufacturer's product description |
| Crown wall thickness | About 1.5 mm | Worked out from the stated sizes, with the hollow placed as on the manufacturer's drawing; not separately stated |
| Side wall thickness | About 3.0 mm | Worked out from 10 mm width and 4 mm core; not separately stated |
| Base thickness under the core | About 1.3 mm | Worked out as above; not separately stated |
| Fixing | Plain base, no adhesive tape: bond with a contact adhesive suited to EPDM sponge | Manufacturer's drawing shows no tape |
| Material | Expanded (sponge) EPDM | Manufacturer datasheet |
| Colour | Black | - |
| Hardness | 40° Shore OO | Shore OO durometer scale (for soft foams); test standard not stated |
| Density | 0.5 to 0.9 g/cm³ | Manufacturer datasheet; method not stated |
| Weight | 31 g/m (product page); 0.03 kg/m (datasheet): about 3.1 kg per 100 m coil | Manufacturer figures |
| Water absorption | 5% maximum | Manufacturer datasheet; method not stated |
| Compression set | 25% maximum (datasheet, 24 h recovery) · 50% (product page, 22 h) | Manufacturer figures; test temperature and standard not stated. The two sources differ, so plan on the higher figure |
| Heat ageing | ±30% change after 7 days at 70 °C | Manufacturer datasheet; property measured not stated |
| Low-temperature flexibility | Pass at -40 °C | Manufacturer datasheet |
| Ozone resistance | Excellent | Manufacturer rating |
| Weather resistance | Excellent | Manufacturer rating |
| UV light resistance | Excellent | Manufacturer rating |
| Mould growth resistance | Very good | Manufacturer rating |
| Service temperature range | Not stated for this profile. Typical for EPDM sponge: about -40 °C to +100 °C (typical for EPDM sponge, not tested on this profile) | Tested points stated: flexible at -40 °C, aged at +70 °C |
| Tensile strength, elongation at break, tear strength | Not stated for this profile | Ask us if you need them |
| Dimensional tolerance | BS 3734 Class E3 (extruded sponge) | BS 3734 |
| Supplied length | Any whole length from 15 m to 99 m as one continuous piece, or a full 100 m coil | - |
| Price per metre | £11.25/m inc VAT for 15–99 m; £9.00/m inc VAT as a full 100 m coil (£900.00) | - |
The manufacturer's sponge-profile catalogue lists this part as 10 × 10 mm; its product page, drawing and datasheet give 10 × 8 mm, which is what we list. The hollow core is stated as 4 × 5.2 mm; the drawing shows it slightly smaller. Sponge sections are flexible, so treat all sizes as nominal.
Materials and compliance
Expanded (closed-cell sponge) EPDM. The manufacturer describes the profile as air and watertight, with good UV and weather resistance, and EPDM as resistant to ozone, heat, steam, ketones and dilute acids and alkalis. Like all EPDM it is not suited to oils, fuels or solvents.
The manufacturer does not state any food-contact (FDA, EC 1935/2004), drinking-water (WRAS), REACH, RoHS or fire-rating approval for this profile, so we do not claim any. If your job needs a certified material, ask us before you order.
How it fits

- Measure the closed gap. It should be smaller than 8 mm so the D is squeezed. About 5 to 6.5 mm (20 to 40% squeeze) is a good starting point; this is our guidance, not a manufacturer figure.
- Check the landing. The face you bond to should be at least 10 mm wide.
- Clean and dry. Degrease with isopropyl alcohol and let it dry.
- Bond the base. Use a contact adhesive suited to EPDM sponge on the flat base. Lay the strip without stretching it, or it will shrink back from the ends.
- Corners and joins. Ease it round gentle corners; for sharp corners cut and butt the ends tightly, or mitre them. Put joins where water will not sit.
How much do I need?
Add up the edges to be sealed and allow about 5% for trimming. Example: eight enclosure doors each 600 × 400 mm need 8 × 2 × (0.6 + 0.4) = 16 m; add 5% and choose 17 m. From 80 m upwards the full 100 m coil costs the same or less, so pick the coil.
Which size do I need?
| Profile | Size (W × H) | Supplied as |
|---|---|---|
| TPE sponge D profile | 6 × 5.5 mm | 100 m coil, self-adhesive |
| EPDM sponge D section | 8 × 10 mm | 50 m coil, self-adhesive |
| EPDM sponge D section (this item) | 10 × 8 mm | 15–99 m cut length or 100 m coil, plain base |
| TPE sponge D profile | 10 × 8 mm | 100 m coil, self-adhesive |
| EPDM sponge D section | 12 × 10 mm | 75 m coil |
Data sheet
Download the technical data sheet (PDF): drawing, full specification and compliance
Questions
How is it sold?
Choose a length from 15 m to 99 m and it is cut as one continuous piece at £11.25 per metre, or choose the full 100 m coil at £900.00. The minimum length is 15 m.
What gap will it seal?
Any closed gap below its 8 mm height. Aim for roughly 5 to 6.5 mm closed. For gaps of 4 mm or less the 6 × 5.5 mm TPE sponge D closes more easily; for gaps over about 7 mm choose the 8 × 10 mm or 12 × 10 mm section.
Is it self-adhesive?
No. The base is plain, so bond it with a contact adhesive suited to EPDM sponge. If you want a peel-and-stick seal of the same size, see the 10 × 8 mm TPE sponge D profile, or ask us.
How do I cut and join it?
A sharp craft knife or scissors gives a clean square end. Butt the ends tightly; for a fully sealed join, bond the ends with a rubber-compatible instant adhesive.
Can I use it outdoors?
Yes. The manufacturer rates its ozone, weather and UV resistance as excellent, and it absorbs no more than 5% water.
What temperatures can it take?
The manufacturer has tested it as flexible at -40 °C and heat-aged it at +70 °C, but does not state a full working range. EPDM sponge typically works from about -40 °C to +100 °C (typical for EPDM sponge, not tested on this profile).
Will it stand up to oil or fuel?
No. EPDM handles water, steam, weather and dilute acids and alkalis well but swells in oils, fuels and most solvents. Ask us for a neoprene or nitrile alternative.
Is it food-safe or WRAS approved?
No approvals are stated for this profile, so do not use it where certified food-contact or drinking-water material is required.
Can I run a cable through the hollow?
Yes, thin cables up to about 3.5 mm can be threaded through the 4 × 5.2 mm core. Leave the core empty if you need the full sealing squeeze or the most impact absorption.
Delivery and help
Held in stock and dispatched from the UK. Trade and quantity orders welcome. Not sure it is the right profile? Call +44 1282 277786 or email sales@industrial-polymers.co.uk and we will check it for you.
Product details
| SKU | IP-EPDMS-10X8-15M |
|---|---|
| Weight | 1.25 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM Sponge D Section – 10mm x 8mm – Cut Length or 100m Coil