
Rubber & FoamSKU IP-EPDMS-16X14-19M
EPDM Sponge Door Seal – 16mm x 14mm Hollow Profile – 19m to 99m or 100m Coil
Price shown updates with the option you pick.
A soft, hollow EPDM sponge seal 16 mm wide and 14 mm high, with one flat 11 mm face to bond against the frame and a rounded nose that squashes down when the door, lid or bonnet closes. Sold as one continuous, unjoined length from 19 m to 99 m, or as a full 100 m coil. Black, in stock and ready to dispatch.
At a glance
- Size: 16 mm wide × 14 mm high, with an 11 mm flat mounting face (nominal, tolerance BS 3734 Class E3)
- Section: D-like hollow profile with a slim slot-shaped core, so it closes down easily under light door pressure
- Material: expanded EPDM sponge, 40° Shore OO, density 0.5–0.9 g/cm³
- Outdoors: ozone, weather and UV resistance rated excellent; flexible at −40 °C
- Fixing: plain profile (no adhesive tape): bond the flat face with a contact adhesive suited to EPDM
- Price per metre: £9.60 inc VAT on cut lengths; about £7.38 per metre on the 100 m coil
Technical drawing

Specifications
| Property | Value | Test method / source |
|---|---|---|
| Overall width | 16 mm (nominal) | Manufacturer drawing |
| Overall height | 14 mm (nominal) | Manufacturer drawing |
| Flat mounting face | 11 mm | Manufacturer drawing |
| Hollow core | Slim slot, roughly 2 mm × 7 mm, set at an angle | Scaled from the manufacturer drawing (not separately stated) |
| Dimensional tolerance | Class E3 | BS 3734 (sponge sizes are approximate as the material compresses) |
| Material | Expanded EPDM sponge | Manufacturer data sheet |
| Colour | Black | Manufacturer data sheet |
| Hardness | 40° Shore OO | Shore OO durometer (method standard not stated) |
| Density | 0.5 – 0.9 g/cm³ | Manufacturer data sheet |
| Water absorption | 5% maximum | Manufacturer data sheet |
| Compression set | 25% maximum (after 24 h recovery) on the data sheet; the supplier's web page lists 50% (22 h) | Manufacturer data sheet / product page; test temperature not stated |
| Heat ageing | ±30% change after 7 days at 70 °C | Manufacturer data sheet |
| Low-temperature flexibility | Pass at −40 °C | Manufacturer data sheet |
| Ozone / weather / UV resistance | Excellent / excellent / excellent | Manufacturer data sheet (rating) |
| Mould growth resistance | Very good | Manufacturer data sheet (rating) |
| Service temperature | About −40 °C to +100 °C | Typical for EPDM sponge, not tested on this profile (−40 °C flexibility is tested) |
| Tensile strength / elongation / tear | Not published for this profile | Ask us if your specification needs them |
| Weight | 0.09 kg/m (data sheet); 140 g/m (supplier web page) | Manufacturer figures; we ship on the higher figure |
| Supplied as | One continuous length 19 m – 99 m, or a 100 m coil | — |
Materials and compliance
Made from expanded EPDM (ethylene propylene diene monomer) sponge rubber, which shrugs off rain, sunlight, ozone and dilute acids and alkalis. The manufacturer does not state any food-contact, drinking-water, FDA, REACH or RoHS approval for this profile, so we do not claim one. If you need a certificate for a particular standard, contact us before ordering.
Typical uses
- Bonnet, scuttle and door seals on classic and restored vehicles (made as a replacement for original part no. BD 4814, a bonnet cantrail seal)
- Door and hatch seals on electrical cabinets, kiosks and plant rooms
- Weather strip on outbuilding, trailer and horsebox doors
- Closure seals in glazing and joinery, and soft gaskets for expansion joints
How much do I need, and which length?
Measure every edge you want to seal and add about 5% for trimming and corners. Example: a cabinet door 1.8 m × 0.8 m has a perimeter of 2 × (1.8 + 0.8) = 5.2 m, so five doors need 26 m; add 5% and order 28 m. If you need 77 m or more, choose the 100 m coil: at £737.55 it costs less than a 77 m cut length.
Fitting tips
- Bond the flat 11 mm face to the frame; the rounded nose meets the closing door.
- Clean and degrease the surface first, then use a contact adhesive suitable for EPDM sponge.
- Lay the seal in without stretching it, or it will shrink back and open gaps at the ends.
- Aim for roughly 25–40% squeeze when closed (a gap of about 9–11 mm with the seal standing 16 mm proud). This is our guidance, not a supplier figure.
Frequently asked questions
How do I fit it?
It has no adhesive backing. Clean the frame, apply a contact adhesive suited to EPDM sponge to the frame and the flat face, let it go tacky and press the seal on without stretching it.
What gap does it seal?
Bonded on its flat face it stands 16 mm proud of the frame, so it suits closed gaps of about 9–11 mm, where it is squeezed by around a third. Much larger gaps will not compress it; much smaller gaps may stop the door closing easily.
Which way up does it go?
Flat side to the frame. The drawing and fitting illustration show the orientation.
What is it made of?
Black expanded EPDM sponge rubber, 40° Shore OO (very soft), density 0.5–0.9 g/cm³.
What temperatures can it take?
The manufacturer confirms it stays flexible at −40 °C. EPDM sponge typically works up to about +100 °C, but that upper figure has not been tested on this profile.
How do I cut and join it?
Cut square with a sharp knife against a straight edge. At corners either bend it round a radius or mitre and glue the ends with a cyanoacrylate (superglue) suitable for rubber, leaving the ends slightly long so they butt tightly.
Is it oil or fuel resistant?
No. EPDM handles water, steam and weather well but is not recommended for constant contact with oils, fuels or solvents.
Will I get one piece?
Yes. Every length from 19 m to 99 m is cut as one continuous, unjoined strip, and the 100 m option is a full coil.
Need a sample or help choosing a profile? Contact our team, call +44 1282 277786 or email sales@industrial-polymers.co.uk.
Related seals
Product details
| SKU | IP-EPDMS-16X14-19M |
|---|---|
| Weight | 5.86 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM Sponge Door Seal – 16mm x 14mm Hollow Profile – 19m to 99m or 100m Coil