
Rubber & FoamSKU IP-EPDMS-12X17-10M
EPDM Sponge Door Seal – 12mm x 17mm – Dual Hardness, Self-Adhesive – 10m to 30m
Price shown updates with the option you pick.
A dual-hardness EPDM door seal, 12 mm wide and 17 mm high. A firm solid rubber base strip (70° Shore A) carries a soft, hollow teardrop bulb of closed-cell EPDM sponge (40° Shore OO) with a short sealing lip on top. The bulb's 8 mm bore lets it squeeze down easily as the door closes, the lip wipes against the door face, and the solid base keeps the line straight and stops the seal twisting. It comes with a self-adhesive backing, so it presses straight onto a clean frame.
Cut to your length in one continuous piece from 10 m to 29 m, or buy a full 30 m coil at a lower price per metre. Black, non-marking. Held in stock.
At a glance
- Size: 12 mm wide × 17 mm high overall
- Sponge bulb: Ø8 mm hollow bore with a 2 mm wall and a 4 mm sealing lip, 40° Shore OO: soft, follows uneven surfaces
- Solid base: 12 mm wide, 70° Shore A EPDM; the bulb joins it on a 5 mm neck
- Temperature: -40 °C to +120 °C (manufacturer's stated range)
- Fixing: self-adhesive backing for wood, plastic, metal and rubber
- Price: £22.47 per metre inc VAT (10–29 m), £17.33 per metre as a 30 m coil
Technical drawing

Which one do I need?
| Seal | Size (W × H) | Shape | Best for |
|---|---|---|---|
| EPDM sponge door seal | 10 × 15 mm | Figure-8 sponge, self-adhesive | Slightly smaller door gaps |
| EPDM sponge door seal (this one) | 12 × 17 mm | Solid base, hollow sponge bulb with lip, self-adhesive | Doors, hatches and cabinets where a firm, straight base helps |
| EPDM sponge boot seal | 12 × 17 mm | All-sponge figure-8, two hollows | Same size, softer all-sponge section |
| EPDM sponge tailgate seal | 10 × 20 mm | Solid foot, tall sponge bulb, plain base | Deeper gaps, bonded in place |
Specifications
| Property | Value | Test method / basis |
|---|---|---|
| Profile type | Dual-hardness door seal: solid rubber base strip carrying a hollow teardrop sponge bulb with a sealing lip | Manufacturer's profile drawing |
| Overall width (across the base) | 12.0 mm | Nominal; tolerance BS 3734 Class E3 |
| Overall height (base to lip tip) | 17.0 mm | Nominal; tolerance BS 3734 Class E3 |
| Bulb bore | Ø8 mm (hollow) | Manufacturer's drawing |
| Sponge wall thickness | 2 mm | Manufacturer's drawing |
| Sealing lip | 4 mm | Manufacturer's drawing |
| Neck width (where the bulb meets the base) | 5 mm | Manufacturer's drawing |
| Height from base to start of sponge bulb | 5 mm | Manufacturer's drawing |
| Solid strip thickness | About 2.5 mm | Scaled from the manufacturer's drawing; not separately stated |
| Fixing | Self-adhesive backing; suits wood, plastic, metal and rubber | Manufacturer's product description and datasheet |
| Material | Solid EPDM base co-extruded with an expanded (sponge) EPDM bulb | Manufacturer datasheet |
| Colour / finish | Black, non-marking | Manufacturer's product description |
| Hardness, solid base | 70° Shore A (product page) · 65–75 IRHD (datasheet) | Shore A / IRHD; test standard not stated |
| Hardness, sponge bulb | 40° Shore OO | Shore OO durometer scale (for soft foams); test standard not stated |
| Density, sponge bulb | 0.5 to 0.9 g/cm³ | Manufacturer datasheet; method not stated |
| Weight | 81 g/m (product page) · 0.09 kg/m (datasheet): about 2.4–2.7 kg per 30 m coil | Manufacturer figures |
| Tensile strength, solid EPDM | 10 MPa | Manufacturer datasheet (solid compound); method not stated |
| Elongation at break, solid EPDM | 500% | Manufacturer datasheet (solid compound) |
| Tear strength, solid EPDM | 50 kN/m | Manufacturer datasheet (solid compound) |
| Compression set, solid EPDM | 21% (22 h at 70 °C) | Manufacturer datasheet (solid compound) |
| Compression set, sponge bulb | 25% maximum (datasheet, 24 h recovery) · 50% (product page, 22 h) | Manufacturer figures; temperature and standard not stated. The two sources differ, so plan on the higher figure |
| Heat ageing, solid EPDM (70 h at 70 °C) | Hardness change 0 IRHD · tensile change +9% · elongation change 0% | Manufacturer datasheet |
| Heat ageing, sponge bulb | ±30% change after 7 days at 70 °C | Manufacturer datasheet; property measured not stated |
| Ozone resistance | No cracks (solid EPDM, 72 h, 40 °C, 22 pphm, extended) · sponge rated excellent | Manufacturer datasheet |
| Water absorption, sponge bulb | 5% maximum | Manufacturer datasheet; method not stated |
| Low-temperature flexibility | Pass at -40 °C | Manufacturer datasheet |
| Service temperature range | -40 °C to +120 °C | Manufacturer's product description |
| Weather / UV light resistance | Excellent / excellent | Manufacturer rating |
| Mould growth resistance | Very good | Manufacturer rating |
| Dimensional tolerance | BS 3734 Class E3 (extruded sponge) | BS 3734 |
| Supplied length | Any whole length from 10 m to 29 m as one continuous piece, or a full 30 m coil | - |
| Price per metre | £22.47/m inc VAT for 10–29 m; £17.33/m inc VAT as a full 30 m coil (£519.75) | - |
Materials and compliance
Solid EPDM base co-extruded with a closed-cell expanded EPDM bulb. The manufacturer describes the seal as air and watertight, non-marking, and resistant to UV, weathering, heat, ozone, steam, ketones and dilute acids and alkalis, with good electrical insulation. Like all EPDM it is not suited to oils, fuels or solvents.
The manufacturer does not state any food-contact (FDA, EC 1935/2004), drinking-water (WRAS), REACH, RoHS or fire-rating approval for this profile, so we do not claim any. If your application needs a certified material, ask us before you order.
Typical uses
- Vehicle, van and trailer doors and hatches
- Marine hatches, lockers and cabin doors
- Electrical enclosures, control cabinets and kiosks
- Glazing and closure seals, weather strip on sheds, garden rooms and outbuildings
- Machine guards and access panels where a soft, quiet close is wanted
How much do I need?
Measure round the opening along the line the seal will follow and add about 5% for trimming and a neat joint. Order that many whole metres. Your length comes as one continuous piece, so there are no joins along the run. From 24 m upwards the full 30 m coil (£519.75) costs no more than the cut length, so it is the better buy.
Fitting
- Clean the frame with a solvent wipe so it is dry and free of dust, grease and wax. Fit at room temperature where you can (the adhesive bonds best above about 10 °C).
- Dry-fit the seal round the opening, base down and the lip facing the door. Start at a bottom corner or a hidden spot so the joint sits out of the water path.
- Peel back the liner a short way at a time and press the base down firmly as you go. Do not stretch the seal; stretched sponge shrinks back and opens a gap at the joint.
- Ease it round corners with a gentle curve rather than a tight fold so the bulb is not kinked.
- Cut the end square with a sharp blade, leave it a couple of millimetres long and push the ends together so the joint is under light compression. A drop of cyanoacrylate on the joint faces makes it permanent.
- Run a roller or thumb along the full length to bed the adhesive in, then close the door gently and check the bulb is squeezed evenly all round.
Frequently asked questions
What door gap does it seal?
The seal stands 17 mm free, and the hollow Ø8 mm bulb does the sealing. It works best where the closed gap is a few millimetres less than 17 mm, so the bulb is squeezed by roughly a quarter to a third; our fitted illustration shows an example closed gap of about 11 mm. The solid base does not compress.
Which way round does it go?
Base down on the frame, bulb up towards the door. The small lip on top should face the door so it wipes the door face as it closes.
Will it stick to metal, wood or plastic?
Yes. The adhesive backing is made for clean wood, plastic, metal and rubber. Painted or powder-coated surfaces must be clean and fully cured. On rough timber or very low-energy plastics, prime the surface first or add a bead of contact adhesive.
Can I use it outdoors?
Yes. EPDM is rated excellent for ozone, weather and UV, stays flexible at -40 °C and has very good resistance to mould growth.
What temperatures will it take?
The manufacturer states -40 °C to +120 °C. Heat-ageing results are given at +70 °C. Very hot surfaces can soften the adhesive before the rubber, so allow for that near heat sources.
How do I cut and join it?
Cut it with a sharp knife or scissors. Butt the ends square and glue the faces with cyanoacrylate. Corners can be mitred, but a gentle bend round the corner seals better and leaves no joint.
Is it oil and fuel resistant?
No. EPDM is excellent outdoors and in water and steam, but it swells in oils, fuels and solvents. Ask us about nitrile or neoprene profiles for those.
How quickly will it arrive?
It is held in stock and cut to your length, so it goes out with our normal dispatch.
Data sheet
Download the technical data sheet (PDF)
Need help choosing a profile? Call +44 1282 277786, email sales@industrial-polymers.co.uk or contact our team.
Product details
| SKU | IP-EPDMS-12X17-10M |
|---|---|
| Weight | 1.98 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM Sponge Door Seal – 12mm x 17mm – Dual Hardness, Self-Adhesive – 10m to 30m