
Rubber & FoamSKU IP-EPDMS-21X25.5-7M
EPDM Sponge Door Seal – 21mm x 25.5mm Hooked Tail Profile – 7m to 49m or 50m Coil
Price shown updates with the option you pick.
A one-piece black EPDM sponge door seal, 21 mm wide and 25.5 mm high, with a long curved tail rising from a flat base that has a hollow slot running through it. As the door closes the tail folds down over the base, so the seal fills large or uneven gaps without making the door hard to shut. It is a common replacement door rubber on classic 4x4 and classic sports-car door apertures, and works equally well on cabinets, hatches, enclosures and timber doors.
At a glance
- Size: 21 mm wide × 25.5 mm high overall, 12.5 × 1.6 mm hollow slot in the base
- Material: expanded (closed-skin) EPDM sponge, 40° Shore OO, black
- Weatherproof: EPDM resists sunlight, ozone and rain; low-temperature flexibility tested at −40 °C
- Lengths: any whole length from 7 m to 49 m in one continuous piece, or a full 50 m coil
- Price: £24.54 per metre inc VAT on cut lengths; the 50 m coil works out at £19.62/m
- In stock in the UK for fast dispatch
Technical drawing

Specification
| Property | Value | Test method / source |
|---|---|---|
| Overall width | 21.0 mm | Manufacturer profile drawing |
| Overall height | 25.5 mm | Manufacturer profile drawing |
| Hollow slot in base | 12.5 mm long × 1.6 mm high | Manufacturer profile drawing |
| Base depth | ≈ 6 mm (approx.) | Scaled from drawing, not separately stated |
| Profile | Curved sponge tail on a flat, slotted base; one-piece extrusion | Manufacturer profile drawing |
| Material | Expanded EPDM sponge | Manufacturer data sheet |
| Colour | Black | — |
| Hardness | 40° Shore OO | Shore OO durometer |
| Density | 0.5 – 0.9 g/cm³ | Manufacturer data sheet |
| Water absorption | 5 % maximum | Manufacturer data sheet |
| Compression set | 25 % max (data sheet, 24 h recovery) · 50 % (product listing, 22 h) | Manufacturer data sheet / listing; conditions not stated further |
| Heat ageing | ±30 % change after 7 days at 70 °C | Oven ageing, manufacturer data sheet |
| Low-temperature flexibility | Pass at −40 °C | Manufacturer data sheet |
| Ozone resistance | Excellent | Manufacturer data sheet |
| Weather resistance | Excellent | Manufacturer data sheet |
| UV resistance | Excellent | Manufacturer data sheet |
| Mould growth resistance | Very good | Manufacturer data sheet |
| Service temperature | About −40 °C to +100 °C | Typical for EPDM sponge, not tested on this profile |
| Tensile strength / elongation / tear | Not published for this profile | — |
| Dimensional tolerance | BS 3734-1 Class E3 (sponge sizes are approximate) | Manufacturer data sheet |
| Weight | 0.1 kg per metre | Manufacturer data sheet |
| Lengths | 7 m to 49 m cut lengths, or full 50 m coil | — |
| Fixing | Not self-adhesive: bond the flat base with a cyanoacrylate or contact adhesive | — |
Materials and compliance
This seal is extruded from expanded EPDM sponge. The manufacturer describes it as non-marking, air- and water-tight and 100 % recyclable. EPDM handles heat, ozone, steam and weathering well and resists dilute acids, alkalis and ketones; it is not suitable for continuous contact with oils, fuels or petroleum solvents.
The manufacturer does not state any food-contact (FDA, EC 1935/2004), WRAS, REACH or RoHS approval for this profile in its documentation, so we do not claim one. If you need a certified material, ask us for an alternative.
How it fits

- Measure the full run you need to seal and add about 100 mm for trimming.
- Prepare the surface: remove the old rubber and glue, treat any rust, then clean with a solvent wipe and let it dry.
- Check the direction: offer a short piece up first so the tail leans the same way as the old seal, usually away from the door's hinge side.
- Bond the flat base a section at a time with cyanoacrylate or contact adhesive. Lay the seal in place without stretching it, or it will shrink back and leave gaps.
- Cut and join with a sharp knife for a square end; butt the ends tightly and glue them together.
- Test: close the door and check for an even, light contact all round.
Choosing a length
Pick the length you need from the Length menu: you receive one continuous piece, with no joins. Cut lengths are £24.54 per metre inc VAT (7 m = £171.78, 20 m = £490.80). The full 50 m coil is £981.00, which is cheaper than any cut length of 40 m or more, so buy the coil if you need 40 m or longer.
Example: a door opening 0.9 m × 1.1 m has a 4.0 m perimeter, so two doors need 8 m.
Frequently asked questions
What gap does this seal suit?
It stands 25.5 mm high when free and folds down to roughly 10–12 mm when the tail is closed over the base, so as a guide it suits door gaps of roughly 12–20 mm. For smaller gaps choose a lower profile; send us a photo of the cut end of your old seal and we'll check it.
Is it self-adhesive?
No. There is no tape on the base. Bond it with a cyanoacrylate (superglue) or a contact adhesive suitable for EPDM.
Which way should the tail face?
Fit it so the door pushes the tail over towards the base as it closes. On most vehicle doors that means the tail leans away from the hinge line, matching the original seal.
Will it fit my classic vehicle?
This profile is widely used as a replacement door rubber on classic 4x4s and classic sports cars. Compare the cut end of your old seal with our drawing: 21 mm wide, 25.5 mm high, a long curved tail and a thin slot in the base.
What temperatures can it take?
The material passes a low-temperature flexibility test at −40 °C. EPDM sponge typically works up to about +100 °C (typical for the material, not tested on this profile).
Can I cut and join it?
Yes. Cut with a sharp knife or scissors for a square end. Butt-join the ends with cyanoacrylate; for corners, mitre or simply bend it round, as the sponge follows radii easily.
Is it suitable for outdoor use?
Yes. The data sheet rates its ozone, weather and UV resistance as excellent, and it absorbs no more than 5 % water.
Will it mark paintwork?
The manufacturer describes the compound as non-marking.
How long is each piece?
The length you choose is supplied as one continuous piece, up to the full 50 m coil.
Related seals
- EPDM Sponge Seal – 22.5mm x 18mm door and window lip seal
- EPDM Sponge Door Seal – 24mm x 33mm
- EPDM Sponge Rear Door Seal – 20mm x 21mm
Not sure it's the right profile? Contact our team on +44 1282 277786 or sales@industrial-polymers.co.uk.
Product details
| SKU | IP-EPDMS-21X25.5-7M |
|---|---|
| Weight | 1.54 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM Sponge Door Seal – 21mm x 25.5mm Hooked Tail Profile – 7m to 49m or 50m Coil