
Rubber & FoamSKU IP-EPDMS-15X24-10M
EPDM Sponge Side Window Seal – 15mm x 24mm – Cut Length
Price shown updates with the option you pick.
A dual-hardness EPDM side window seal, 15 mm wide by 24 mm high. The lower half is a solid 70° Shore A EPDM grip base with a 2 mm slot that clips onto the frame; the upper half is a soft 40° Shore OO expanded EPDM sponge lobe that the glass closes against. It is made as an aftermarket replacement for the opening side window seal on classic Minis and suits any window, hatch or panel that needs a firm clip-on base and a deep, soft sealing face. Sold as one continuous, unjoined strip in any whole-metre length from 10 m to 49 m, or as a full 50 m coil.
At a glance
- Size: 15 mm wide × 24 mm high overall; 11 mm solid base, 13 mm sponge lobe
- Grip slot: 2 mm wide with a 3 mm solid floor beneath it
- Two hardnesses: 70° Shore A base holds its shape; 40° Shore OO sponge compresses easily
- Weather sealing: closed-cell sponge, 5% maximum water absorption, excellent ozone, UV and weather resistance
- Cold flexible: passes low-temperature flexibility at -40°C
- Price per metre: £18.87 inc VAT (£15.73 ex VAT) for 10–49 m; the 50 m coil works out at £14.54 inc VAT per metre
Technical drawing

Specification
| Property | Value | Test method / basis |
|---|---|---|
| Overall width | 15 mm | Manufacturer's drawing |
| Overall height | 24 mm | Manufacturer's drawing |
| Solid grip base height | 11 mm | Manufacturer's drawing |
| Sponge lobe height | 13 mm | Manufacturer's drawing |
| Grip slot width | 2 mm | Manufacturer's drawing |
| Solid floor under slot | 3 mm | Manufacturer's drawing |
| Dimensional tolerance | Class E3 | BS 3734 |
| Weight | 0.17 kg per metre (170 g/m) | Manufacturer's data |
| Lengths | 10 m to 49 m in 1 m steps, one piece; or 50 m full coil | — |
| Colour | Black | — |
| Solid base: dense EPDM | ||
| Hardness | 70° Shore A (65–75 IRHD) | IRHD |
| Tensile strength | 10 MPa | Manufacturer's data sheet |
| Elongation at break | 500% | Manufacturer's data sheet |
| Tear strength | 50 kN/m | Manufacturer's data sheet |
| Compression set | 21% | 22 h at 70°C |
| Ozone resistance | No cracks | 72 h at 40°C, 22 pphm, extended |
| Heat ageing: hardness change | 0 IRHD | 70 h at 70°C |
| Heat ageing: tensile change | +9% | 70 h at 70°C |
| Heat ageing: elongation change | 0% | 70 h at 70°C |
| Sealing lobe: expanded EPDM sponge | ||
| Hardness | 40° Shore OO | Shore OO |
| Density | 0.5–0.9 g/cm³ | Manufacturer's data sheet |
| Water absorption | 5% maximum | Manufacturer's data sheet |
| Compression set | 25% maximum (data sheet, 24 h recovery); 50% quoted on the product page (22 h) | Manufacturer's data |
| Oven ageing | ±30% | 7 days at 70°C |
| Low-temperature flexibility | Pass | -40°C |
| Ozone / weather / UV resistance | Excellent / excellent / excellent | Manufacturer's rating |
| Mould growth resistance | Very good | Manufacturer's rating |
| Working temperature | -40°C to +120°C | Manufacturer's stated range for the EPDM |
Sponge dimensions are nominal because the sponge is compressible. Values are the manufacturer's for this profile.
Materials and compliance
Both sections are EPDM (ethylene propylene diene rubber): a dense compound for the base and a closed-cell expanded compound for the lobe. EPDM resists weather, ozone, UV, steam, dilute acids, alkalis and ketones, and is a good electrical insulator. It is not suited to petrol, mineral oils or greases. The manufacturer does not state any food-contact, WRAS, flame-retardant, REACH or RoHS approval for this profile, so we do not claim one.
Typical uses
- Opening side window seal on classic Mini saloons and other small classic cars
- Window, hatch and quarter-light seals on restorations and kit cars
- Clip-on weather seal for sliding windows on cabs, kiosks and plant enclosures
- Glazing and closure seals in construction and joinery
How much do I need?
Measure the full run of each window opening and add about 5% for trimming. Two side windows of 0.75 m × 0.35 m need 2 × 2 × (0.75 + 0.35) = 4.4 m, so a 10 m length does two cars with some spare. From 39 m upward the 50 m coil costs less than the cut length, so choose the coil.
Fitting tips
- Clean the frame and dry-fit a short piece first to check the 2 mm slot grips the frame edge firmly.
- Start the run at the bottom centre so the joint sits away from the main water path.
- Press the base on along the run; a little soapy water helps it slide on. Ease it round corners rather than stretching it.
- Cut square with a sharp knife and butt the ends tightly; a dab of EPDM-compatible adhesive seals the joint.
Frequently asked questions
How does it fix in place?
The solid 70° Shore A base has a 2 mm grip slot that clips onto the frame edge, so no adhesive is needed along the run. Use adhesive only at the butt joint, or along the run if the edge you are fitting to is thinner than the slot.
Will it fit my car?
It is made as a replacement for the classic Mini opening side window seal. For anything else, compare the 15 × 24 mm section and the drawing above with your old seal, or email a photo of the old seal's cut end to sales@industrial-polymers.co.uk and we will check it.
What gap does it seal?
The lobe stands 13 mm above the base and is designed to be squeezed. Aim for the closed glass or panel to compress the sponge by roughly a quarter to a third of its height.
Is it waterproof?
Yes. The sponge is closed-cell, with a 5% maximum water absorption, so it keeps out rain and draughts when compressed.
What temperatures can it take?
-40°C to +120°C. The sponge passes the manufacturer's -40°C flexibility test, so it stays soft in winter.
Can I cut and join it?
Yes. It cuts cleanly with a sharp knife or scissors. Butt-join the ends with an EPDM-compatible adhesive; mitre the corners if you prefer a neat joint.
Will it come in one piece?
Yes. Every length from 10 m to 49 m is cut as one continuous strip, and the 50 m option is a full factory coil.
Is it oil resistant?
No. EPDM is not suited to petrol or mineral oil. For oily areas ask us about a nitrile or neoprene profile.
Need help choosing? Call +44 1282 277786, email sales@industrial-polymers.co.uk or use our contact page.
Complete your project
Product details
| SKU | IP-EPDMS-15X24-10M |
|---|---|
| Weight | 3.75 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM Sponge Side Window Seal – 15mm x 24mm – Cut Length