
Rubber & FoamSKU IP-EPDM-23X5-7
EPDM T Glazing Seal 23mm x 5mm – Caravan Window Lip Seal for 6mm Channels – 7m to 30m
Price shown updates with the option you pick.
This EPDM T glazing seal is a 23mm wide solid black rubber lip seal for caravan, motorhome and trailer windows. Its grooved 5mm head pushes into a frame channel up to 6mm wide, and a flexible 20mm tapered lip sweeps down onto the glazing to keep wind and rain out. It is cut to your length from 7m up to a full 30m coil and dispatched from stock.
At a glance
- Size: 23mm overall width, 5mm head, 20mm sealing lip
- Fits: frame channels and slots up to 6mm wide
- Material: solid EPDM, black, 65–75° Shore A
- Temperature: −40°C to +120°C
- Weathering: good resistance to UV, ozone and outdoor exposure
- Sold as: one cut length, 7m to 29m in 1m steps, or a full 30m coil
- Price: £25.00 per metre inc VAT on cut lengths; the 30m coil works out at £17.92 per metre
Typical uses
- Replacing a perished, cracked or shrunken lip seal on caravan opening and fixed windows
- Re-sealing motorhome, horsebox and trailer glazing where the frame has a narrow retaining slot
- Draught and rain sealing round glazed hatches and panels with a matching channel
Technical drawing

How it fits

In use

Specifications
| Property | Value | Test method / condition |
|---|---|---|
| Profile type | T glazing seal with grooved head and curved tapered lip | — |
| Overall width | 23 mm | Nominal, manufacturer's drawing |
| Head height | 5 mm | Nominal, manufacturer's drawing |
| Sealing lip length (from head to tip) | 20 mm | Nominal, manufacturer's drawing |
| Head groove (neck) height | 1.8 mm | Nominal, manufacturer's drawing |
| Front flange thickness | 1.6 mm | Nominal, manufacturer's drawing |
| To fit channel / slot | Up to 6 mm wide | Manufacturer's fitting data |
| Dimensional tolerance | Not published for this profile | Ask us if you need a tolerance before ordering |
| Material | Solid EPDM (ethylene propylene diene monomer) | — |
| Colour | Black | — |
| Hardness | 65–75° Shore A | Shore A durometer |
| Tensile strength | 8.5 MPa | At break, unaged |
| Elongation at break | 285 % | Unaged |
| Compression set | 20 % | 22 h at 70 °C |
| Hardness change after ageing | +1° Shore A | Heat aged 70 h at 70 °C |
| Tensile strength change after ageing | +4 % | Heat aged 70 h at 70 °C |
| Elongation change after ageing | −9 % | Heat aged 70 h at 70 °C |
| Operating temperature | −40 °C to +120 °C | Continuous service range |
| Density | Not published for this profile | — |
| Tear strength | Not published for this profile | — |
| Lengths available | 7 m to 29 m in 1 m steps; full coil 30 m | Minimum order 7 m |
Materials and compliance
Made from solid (non-cellular) EPDM rubber, a synthetic elastomer chosen for outdoor seals because it shrugs off sunlight, ozone, rain and temperature swings far better than natural rubber or PVC. The figures above are the manufacturer's published values for this profile.
No food-contact, potable-water, fire-rating or other third-party approvals are claimed for this seal. If your project needs a certificate, contact us before ordering.
How much do I need?
Measure round the full length of the window channel and add about 5% for trimming. For example, a 1200 x 600mm window has a 3.6m perimeter, so two such windows need about 7.6m including trimming – order 8m. If you are re-sealing several windows, the full 30m coil costs less than the 22m cut length and is the best value per metre.
Fitting tips
- Remove all of the old seal and any sealant, then clean the channel so the head can seat fully.
- Start at the bottom centre of the window and press the head into the channel with your thumbs, working round a little at a time.
- Feed the seal in without stretching it; stretched rubber shrinks back over time and opens gaps at the corners.
- Check the lip faces the glazing and lies evenly along its whole length.
- Cut the ends square with a sharp knife and butt them tightly together, ideally at the bottom of the window.
Frequently asked questions
How do I know if this seal will fit my window?
Check that the frame has a channel or slot up to 6mm wide and that your old seal has a narrow head with a single long lip roughly 20mm wide. Compare the end of your old seal with the drawing above; if in doubt, send us a photo of the cut end next to a ruler.
Which way round does it go?
The grooved head goes into the channel and the curved lip points towards the glazing, with its tip resting on the glass or acrylic pane.
What is it used for?
Mainly as a replacement lip seal on caravan and motorhome windows, both opening and fixed, and on trailer or horsebox glazing that uses the same style of channel.
Will it stand up to sun and frost?
Yes. It is solid EPDM rated from −40°C to +120°C, with good resistance to UV and ozone, so it suits year-round outdoor use.
Can I cut and join it?
Yes. Cut it with a sharp knife or scissors. Butt the ends tightly together; for a fully bonded joint, use a cyanoacrylate adhesive suitable for EPDM rubber.
Is it supplied in one piece?
Yes. Each length is cut as a single piece from the coil, so a whole window can usually be done with only one joint.
Can I buy less than 7m?
No, 7m is the shortest length we supply for this profile. Any spare is useful for future repairs.
Why is the 30m coil cheaper than cut lengths of 22m or more?
30m is a full, uncut coil, so it carries no cutting cost and is priced lower per metre.
Need help choosing a glazing seal? Contact our team on +44 1282 277786 or sales@industrial-polymers.co.uk.
Related glazing seals
Product details
| SKU | IP-EPDM-23X5-7 |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM T Glazing Seal 23mm x 5mm – Caravan Window Lip Seal for 6mm Channels – 7m to 30m