
Rubber & FoamSKU IP-EPDMU-8.4X21-50M-COIL
EPDM U Channel – 8.4mm x 21mm for 2.4mm Panels – 50m Coil
A tall, tapered-grip edge trim for 2.4 mm panels. This solid black EPDM U channel is 8.4 mm wide and 21 mm high, with a 2.4 mm slot, 3 mm thick legs and a fully rounded crown. The inner channel tapers so the long legs pinch the panel harder near the open end, which means it often holds without adhesive. Supplied as one continuous 50 m coil and held in stock in the UK.
At a glance
- Fits 2.4 mm panels: the 2.4 mm slot grips both faces of 2.4 mm sheet metal, glass, acrylic, polycarbonate or board.
- Tall 8.4 × 21 mm profile: 3 mm walls and long gripping legs give a wide cushioned band on both sides of the sheet.
- Solid EPDM, 65 Shore A: 69 ±5 IRHD, tensile strength 10.5 MPa, elongation at break 315%, compression set only 7%.
- Rated −40 °C to +120 °C: no cracks in the −30 °C cold-bend test or the UV test; good resistance to weathering, ozone, flexing and abrasion.
- No special tools: push on by hand and cut with a sharp knife. Bond with PU or silicone sealant for a permanent or sealed fit.
- 50 m coil, one piece: £545.40 inc VAT, which works out at £10.91 per metre. About 7.85 kg.
Technical drawing

Nominal dimensions in mm. The 8.4 mm width, 21 mm height, 2.4 mm slot and 3 mm leg dimension are the manufacturer's figures. The 3 mm wall at the crown is (8.4 − 2.4) ÷ 2, which agrees with the 3 mm leg. The amount of taper in the slot is not published, so it is drawn for illustration only.
Specifications
| Property | Value | Test method / source |
|---|---|---|
| Profile type | Round-crown U channel (edge trim) with tapered inner channel | Manufacturer's drawing |
| Overall width | 8.4 mm | Manufacturer's drawing, nominal |
| Overall height (depth over the panel) | 21 mm | Manufacturer's drawing, nominal |
| Slot (channel) width | 2.4 mm | Manufacturer's drawing, nominal |
| Fits panel thickness | 2.4 mm | Manufacturer's data sheet |
| Leg thickness at the open end | 3 mm | Manufacturer's drawing, nominal |
| Wall thickness at the crown | 3 mm (calculated) | (8.4 − 2.4) ÷ 2 |
| Material | Solid EPDM (ethylene propylene diene monomer) | Manufacturer's data sheet |
| Colour | Black | – |
| Hardness | 65 Shore A | Shore A, manufacturer's product data |
| Hardness (compound) | 69 ±5 IRHD | IRHD, manufacturer's material sheet |
| Tensile strength | 10.5 MPa (compound sheet); 9 MPa quoted for the profile | Manufacturer's material sheet / product data |
| Elongation at break | 315% | Manufacturer's material sheet |
| Tear strength | 12 kN/m | Manufacturer's material sheet |
| Compression set | 7% | 22 h at 70 °C |
| Ozone resistance | Rating 6 | 98 h at 40 °C, 100 pphm |
| Cold bend | No cracks | −30 °C |
| UV stability | No cracks | Manufacturer's material sheet |
| Migration resistance | 0.02 mg | Manufacturer's material sheet |
| Staining | No stain | Manufacturer's material sheet |
| Heat ageing: change in hardness / tensile / elongation | +2° / +5% / 0% | 70 h at 70 °C |
| Heat ageing: change in hardness / tensile / elongation | +2° / −1% / +7% | 10 days at 70 °C |
| Service temperature | −40 °C to +120 °C | Manufacturer's product data |
| Weight | 157 g per metre (50 m coil about 7.85 kg) | Manufacturer's product data |
| Supplied as | One continuous 50 m coil | – |
| Density | Not stated for this profile | – |
| Dimensional tolerance | Not stated; extruded rubber is normally made to ISO 3302-1 tolerance classes | – |
Materials and compliance
This profile is extruded from a solid EPDM compound. EPDM resists weathering, ozone, UV and water and stays flexible from cold winters to hot plant rooms. The manufacturer states the material is 100% recyclable. All test results in the table come from the manufacturer's data for this profile and its compound.
The manufacturer does not state any food-contact (FDA or EC 1935/2004), WRAS, REACH, RoHS or fire approval for this product, so we do not claim one. If your application needs a certified material, please contact us before ordering.
How it fits

Is a 50 m coil right for you?
Add up the total length of edge to cover. For example, eight 2.4 mm guard panels of 1,200 × 800 mm edged all round need 8 × 4 m = 32 m, plus about 5% for cuts and joints: one 50 m coil does the job with spare. At £10.91 per metre a full coil is the most economical way to buy this size of trim.
Typical uses
- Sheet metal machine guards, covers and enclosure doors made from 2.4 mm sheet
- Protective edge on 2.4 mm glass, acrylic and polycarbonate screens
- Hiding rough, burred or uneven cut edges on sheet and board
- Vending machines, kiosks, shop fittings and furniture panels
- Stairs, steps, kick plates and running boards
- Bonded into aluminium window or panel channels as a sealing strip
Fitting
- Deburr and clean the edge. Check with a caliper that the sheet is 2.4 mm thick.
- Start at a corner and press the channel on by hand, working along the edge. A soft-faced mallet helps on long runs.
- On outside corners, ease the trim round the bend. On tight corners, cut a small V-notch out of the legs.
- Cut a few millimetres long with a sharp knife, then push the ends together into a tight butt joint.
- For a sealed or permanent fit, run a bead of PU or silicone sealant into the slot first.
FAQ
What panel thickness does it fit?
2.4 mm panels. To use it on a thinner sheet, bond a thin rubber strip inside the slot to pack it out. For 2 mm sheet choose the 7 × 21 mm channel; for 4.8 mm panels choose the 12.8 × 21.5 mm channel. A 3 mm edge will not fit this slot.
Do I need to glue it?
Usually not. The tapered slot and long legs give a firm mechanical grip on 2.4 mm sheet. Use PU or silicone sealant where it must seal, where there is heavy vibration, or on a panel at the thin end of the tolerance.
How do I measure what I need?
Measure the panel thickness with a caliper first, then add up the total edge length in metres and allow about 5% extra for cuts and joints.
Can it be used outdoors?
Yes. EPDM is chosen for outdoor use: this compound showed no cracks in the UV test and the −30 °C cold-bend test, and resists weathering and ozone.
What temperatures can it take?
The manufacturer rates it from −40 °C to +120 °C. Its properties barely changed after 10 days at 70 °C.
How do I cut and join it?
Use a sharp knife or heavy shears and cut square. Butt the ends together tightly. For a sealed joint, add a little cyanoacrylate glue or sealant to the cut faces.
Will it go round corners?
It follows gentle curves easily. For sharp outside corners, notch the legs from the inside so the crown bends neatly, or cut and butt-join the ends.
Is it soft or firm?
At 65 Shore A it is medium-firm: soft enough to absorb knocks, firm enough to hold its shape and grip the panel. The low 7% compression set means it keeps its grip over time.
Can I make the trim wider or fit a thinner panel?
Yes. Bond a neoprene strip alongside the channel to widen the finished edge, or bond a strip inside the slot to suit a thinner panel.
Is it food-safe or certified?
The manufacturer states no food-contact or other approvals for this product, so we do not claim any. Ask us about certified alternatives.
Is it in stock?
Yes. 50 m coils are held in stock and dispatched from the UK.
Related profiles
- EPDM U Channel 7 × 21 mm, for 2 mm panels, 6 m to 30 m
- EPDM U Channel 5.6 × 19 mm, for 1.6 mm panels
- EPDM U Channel 12.8 × 21.5 mm, for 4.8 mm panels
- TPE U Channel 8.4 × 20 mm, for 1.5 mm panels, 50 m coil
- EPDM Square U Channel 14.7 × 22 mm
Need help choosing? Call +44 1282 277786 or email sales@industrial-polymers.co.uk.
Product details
| SKU | IP-EPDMU-8.4X21-50M-COIL |
|---|---|
| Weight | 17.31 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM U Channel – 8.4mm x 21mm for 2.4mm Panels – 50m Coil