
Rubber & FoamSKU IP-EPDMU-9X9X1.6-7
EPDM Round U Channel – 9mm x 9mm – Fits 1.6mm Panel – Cut Length or 30m Coil
Price shown updates with the option you pick.
A solid, round rubber bumper for thin 1.6 mm sheet. This black EPDM round U channel is a 9 mm diameter solid section with a narrow parallel slot 1.6 mm wide and 4.5 mm deep. It leaves 3.7 mm of rubber on each side of the panel and 4.5 mm of solid rubber over the cut edge, so a thin, sharp sheet edge becomes a smooth, cushioned 9 mm round. Choose one continuous length from 7 m to 29 m, or a full 30 m coil. Every length is held in stock in the UK.
At a glance
- Fits 1.6 mm panels: parallel 1.6 mm slot, 4.5 mm deep, grips both faces of 16-gauge sheet.
- 9 × 9 mm solid round section: 3.7 mm side walls and 4.5 mm of solid rubber over the edge.
- Solid EPDM, 65–75 Shore A: tensile strength 10 MPa, elongation at break 500%, tear strength 50 kN/m.
- Made for outdoor use: no cracks after a 72 h ozone test, and little change after heat ageing at 70 °C.
- No tools needed: push on by hand and cut with a sharp knife. Bond with PU or silicone sealant for a permanent or sealed fit.
- Any length from 7 m to 30 m: one continuous piece. The 30 m full coil has the lowest price per metre.
Technical drawing

Nominal dimensions in mm, free (unfitted) state. Width, height, slot width, slot depth and wall thickness are the manufacturer's figures. The 4.5 mm below the slot is worked out from them (9.0 − 4.5).
Specifications
| Property | Value | Test method / source |
|---|---|---|
| Profile type | Round U channel (solid round section with a centre slot) | Manufacturer's drawing |
| Overall width | 9 mm | Manufacturer's drawing, nominal |
| Overall height | 9 mm | Manufacturer's drawing, nominal |
| Slot (channel) width | 1.6 mm, parallel sides | Manufacturer's drawing and data |
| Slot depth | 4.5 mm | Manufacturer's drawing |
| Side wall thickness | 3.7 mm | Manufacturer's technical data ("thickness") |
| Solid rubber below slot | 4.5 mm (9.0 − 4.5) | Derived from manufacturer's drawing |
| Fits panel thickness | 1.6 mm | Manufacturer's data sheet |
| Material | Solid EPDM (ethylene propylene diene monomer) | Manufacturer's data sheet |
| Colour | Black | – |
| Hardness | 65–75 IRHD (±5), stated as 65–75 Shore A | IRHD, manufacturer's data sheet |
| Tensile strength | 10 MPa | Manufacturer's data sheet |
| Elongation at break | 500% | Manufacturer's data sheet |
| Tear strength | 50 kN/m | Manufacturer's data sheet |
| Compression set | 21% | 22 h at 70 °C |
| Ozone resistance | No cracks | 72 h at 40 °C, 25 pphm |
| Heat ageing: change in tensile strength | +9% | 70 h at 70 °C |
| Heat ageing: change in elongation at break | 0% | 70 h at 70 °C |
| Weight | 0.07 kg per metre (30 m coil about 2.1 kg) | Manufacturer's data |
| Lengths available | 7, 8, 9 … 29 m, or a full 30 m coil (one continuous piece) | – |
| Service temperature | about −40 °C to +120 °C, typical for EPDM, not tested on this profile | General EPDM data |
| Density | Not stated for this profile | – |
| Dimensional tolerance | Not stated; extruded rubber is normally made to ISO 3302-1 tolerance classes | – |
Materials and compliance
This profile is extruded from a solid EPDM compound. EPDM resists weathering, ozone, UV and water, and stays flexible over time. The test results in the table come from the manufacturer's data sheet for this profile.
The manufacturer does not state any food-contact, WRAS, REACH, RoHS or fire approval for this product, so we do not claim one. If your application needs a certified material, please contact us before ordering.
How it fits

Choosing your length
Add up the total length of edge to be covered and allow about 5% extra for cutting and joints. For example, a 2,500 × 1,250 mm sheet edged on all four sides needs about 7.5 m, so an 8 m length covers one sheet and a 16 m length covers two. The price covers one continuous piece of the length you choose.
| Length | Price inc VAT | Price per metre |
|---|---|---|
| 7 m | £167.01 | £23.86 |
| 10 m | £238.59 | £23.86 |
| 15 m | £357.90 | £23.86 |
| 20 m | £477.18 | £23.86 |
| 25 m | £596.49 | £23.86 |
| 29 m | £691.92 | £23.86 |
| 30 m full coil | £617.40 | £20.58 |
Need 26 m or more? The full 30 m coil costs less than any length from 26 m to 29 m.
Typical uses
- Edges of 1.6 mm (16-gauge) steel and aluminium sheet on guards, enclosures, cabinets and machine covers
- Thin acrylic, polycarbonate and composite panels on screens and displays
- Glass and glazing edges, vending machines and shop fittings
- Doors, hatches and access panels that need a soft, rounded safe edge
- Stair edges, running boards, trailer and vehicle panels
- Bonded into aluminium window channels as a push-in seal
Fitting
- Deburr and clean the edge. Check the sheet is 1.6 mm thick.
- Start at a corner and press the channel on with your thumb as you work along.
- On outside corners, ease the trim round the bend. On tight corners, cut a small V-notch out of the section below the slot.
- Cut a few millimetres long with a sharp knife, then push the ends together into a tight butt joint.
- For a sealed or permanent fit, run a bead of PU or silicone sealant into the channel first.
FAQ
What panel thickness does it fit?
1.6 mm sheet (16 gauge). The slot is 1.6 mm wide with parallel sides, so it grips a 1.6 mm edge along its full depth. A thinner sheet can be packed out by bonding a thin strip inside the channel. It is not designed for sheet thicker than 1.6 mm.
How do I measure what I need?
Measure the panel thickness with a caliper first, then measure the total edge length in metres and round up. Allow about 5% extra for cuts and joints.
How much of the panel face does it cover?
The slot is 4.5 mm deep, so the trim covers the edge and about 4.5 mm of each face once pushed fully home. The finished edge is a 9 mm round.
What is it used for?
Guarding sharp thin-sheet edges on machine guards, enclosures, glazing, vending machines, doors, steps and trailers. The solid round section makes a good bumper where people or equipment knock against an edge.
Can it be used outdoors?
Yes. EPDM is chosen for outdoor use because it resists weathering and ozone. This compound passed a 72 h ozone test with no cracks.
What temperatures can it take?
The manufacturer has not published a temperature range for this profile. EPDM is typically used from about −40 °C to +120 °C, but this has not been tested on this profile. The compound did pass heat ageing for 70 h at 70 °C with little change in properties.
How do I cut and join it?
Use a sharp knife or heavy shears and cut square. Butt the ends together tightly. For a sealed joint, add a little cyanoacrylate glue or sealant to the cut faces.
Is it soft or firm?
At 65–75 Shore A it is medium-firm: soft enough to absorb knocks, and firm enough to hold its round shape and grip the panel.
Why is the 30 m coil cheaper than 29 m?
30 m is a full, uncut coil, so there is no cutting or handling, and it is priced lower. If you need 26 m or more, the coil is the cheaper buy.
Is it food-safe or certified?
The manufacturer states no food-contact or other approvals for this product, so we do not claim any. Ask us about certified alternatives.
Is it in stock?
Yes. All lengths are held in stock and dispatched from the UK.
Data sheet
Download the technical data sheet (PDF)
Related profiles
- EPDM Round U Channel 7 × 7 mm, for 1.6 mm panels
- EPDM U Channel 4.5 × 9 mm, for 1.6 mm panels
- Neoprene Round U Channel 6.5 × 10.5 mm, for 1.6 mm panels
- Neoprene Round U Channel 6 × 13.5 mm, for 1.6 mm panels
Need help choosing? Call +44 1282 277786 or email sales@industrial-polymers.co.uk.
Product details
| SKU | IP-EPDMU-9X9X1.6-7 |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM Round U Channel – 9mm x 9mm – Fits 1.6mm Panel – Cut Length or 30m Coil