
Rubber & FoamSKU IP-SGET-10.5X14.3-40
Self-Grip PVC Edge Trim – 10.5mm x 14.3mm – Fits 1.5mm to 3mm Panels – 40m to 50m
Price shown updates with the option you pick.
A black PVC push-on edge trim with a steel carrier, made for thin sheet edges from 1.5 mm to 3 mm. It is 10.5 mm wide and 14.3 mm high, with a 3.5 mm mouth. A U-shaped steel strip runs through the PVC for its whole length. Inside the channel, four barbed fins (two on each wall, staggered) bite on both faces of the panel, so the trim holds by clamping force alone with no glue. It covers sharp cut edges, protects the panel and the people around it from knocks, and leaves a neat rounded finish. Choose any length from 40 m to 49 m in one continuous piece, or a full 50 m coil. It is in stock in the UK for same-day dispatch.
At a glance
- Fits: sheet metal, plastic, fibreglass and board edges 1.5 mm to 3 mm thick
- Size: 10.5 mm wide × 14.3 mm high; 3.5 mm mouth
- Construction: flexible PVC, 70° ± 3° Shore A, over a U-shaped steel carrier
- Grip: four barbed internal fins; push on by hand, no adhesive, and it can be removed and refitted
- Working temperature: −10 °C to +60 °C, indoors or outdoors
- Weight: about 0.07 kg per metre
- Lengths: 40 m to 49 m in 1 m steps at about £4.05 per metre, or a full 50 m coil at £189.24 (£3.78 per metre)
Technical drawing

All dimensions are in mm and nominal. The drawing is not to scale; the carrier and fin shapes are shown as typical.
Specifications
| Property | Value | Test method / basis |
|---|---|---|
| Profile | Self-gripping U edge trim with steel carrier and four barbed internal fins | Manufacturer drawing |
| Overall width | 10.5 mm | Manufacturer drawing and data sheet |
| Overall height | 14.3 mm | Manufacturer drawing and data sheet |
| Mouth opening (unflexed) | 3.5 mm | Manufacturer drawing |
| Panel thickness it fits | 1.5 mm to 3 mm | Manufacturer drawing, data sheet and product page (one table on the maker's page says 3.4 mm; we quote the lower figure) |
| Side wall each side of the mouth | 3.5 mm | Calculated: (10.5 − 3.5) ÷ 2 |
| Section thickness | 2 mm | Manufacturer figure; measuring point not stated |
| Jacket material | Flexible PVC | Manufacturer |
| Carrier | Steel, U-shaped, full length | Manufacturer |
| Colour | Black | Manufacturer |
| Hardness | 70° ± 3° Shore A | Manufacturer data sheet; method not stated |
| Density | 1.40 g/cm³ (range 1.35 to 1.45 g/cm³) | Manufacturer data; method not stated |
| Tensile strength | More than 11 MPa | Manufacturer data; method not stated |
| Elongation at break | 260 % or more | Manufacturer data; method not stated |
| Minimum working temperature | −10 °C | Manufacturer product data (the material sheet quotes −25 °C for the PVC compound) |
| Maximum working temperature | +60 °C | Manufacturer product data (the material sheet quotes +75 °C for the PVC compound) |
| Weight | 0.07 kg per metre (about 3.5 kg for a 50 m coil) | Manufacturer data |
| Tear strength | Not stated for this profile | Ask us if you need it |
| Compression set | Not stated for this profile | Ask us if you need it |
| Dimensional tolerance | Not stated for this profile | Ask us if you need it |
| Supplied as | One continuous piece, 40 m to 50 m | — |
Lengths and prices
Every length is one continuous piece with no joins. Prices include VAT.
| Length | Price | Per metre |
|---|---|---|
| 40 m | £161.82 | £4.05 |
| 41 m | £165.87 | £4.05 |
| 42 m | £169.92 | £4.05 |
| 43 m | £173.97 | £4.05 |
| 44 m | £177.99 | £4.05 |
| 45 m | £182.04 | £4.05 |
| 46 m | £186.09 | £4.05 |
| 47 m | £190.14 | £4.05 |
| 48 m | £194.19 | £4.05 |
| 49 m | £198.24 | £4.05 |
| 50 m full coil | £189.24 | £3.78 |
Tip: if you need 47 m or more, the full 50 m coil costs less than the cut length.
To work out how much you need, add up the length of every edge you want to cover and allow about 5 % extra for cutting at corners and ends. Example: 12 enclosure doors with 3.5 m of edge each need 42 m; with 5 % extra that is 44.1 m, so choose 45 m.
How it fits

- Check the edge. It should be 1.5 mm to 3 mm thick, deburred, clean and dry.
- Push on. Start at one end and press the trim fully home by hand, working along the edge. Do not stretch it as you go; ease it on slightly compressed so it does not shrink back from the ends later.
- Seat it. Tap along the top with a rubber or plastic mallet until the panel reaches the top of the channel. No adhesive is needed.
- Cut and finish. Cut through the PVC and the steel carrier with side cutters, tin snips or a fine-tooth hacksaw. Butt the ends tightly together.
Typical uses
- Cut edges of steel and aluminium sheet on machine guards, enclosures and cabinets
- Garage doors, shed panels and sheet-metal fabrications
- Fibreglass and plastic panels on vehicles, trailers and marine equipment
- Playground and leisure equipment, where exposed edges must be covered
- Interior side panels, partitions and the edges of side windows
Which edge trim do I need?
Measure the thickness of the edge with a vernier or ruler, then pick the trim whose range covers it:
- Edges 1 mm to 1.5 mm: Self-Grip PVC Edge Trim 5.5 × 8.5 mm
- Edges 1.5 mm to 3 mm: this trim, 10.5 × 14.3 mm
- Edges 3.5 mm to 4.5 mm: Self-Grip PVC Edge Trim 10 × 13.5 mm
- Edges 8 mm to 9.5 mm: Self-Grip PVC Edge Trim 12 × 15.5 mm
Materials and compliance
The jacket is flexible PVC, which resists weathering, moisture and many everyday chemicals, so the trim can be used indoors and outdoors. The steel carrier gives a stronger clamping force than a wire carrier. Because the carrier is one continuous strip, the trim bends easily round curves in the plane of the panel, but it has a limited bending radius sideways.
The manufacturer does not state any product approvals (such as FDA, EC 1935/2004, WRAS, REACH or RoHS) for this trim, so we do not claim any. If you need a declaration for your application, contact us before ordering.
Frequently asked questions
Do I need glue to fit it?
No. The steel carrier and the four barbed fins clamp onto the panel. You push it on by hand and seat it with a rubber mallet. Because there is no adhesive, it can be pulled off and refitted.
What thickness of panel does it fit?
Edges from 1.5 mm to 3 mm thick. On thinner edges it will not grip firmly, and thicker edges will not go fully into the channel. For other thicknesses see the size guide above.
How do I cut it and join the ends?
Cut straight through the PVC and the steel carrier with side cutters, tin snips or a fine-tooth hacksaw. Where two ends meet, cut them square and butt them tightly together; no joining piece is needed.
Will it go round corners?
It follows curves and radiused corners in the plane of the panel. For a sharp 90° corner, cut a small V-notch in the bottom of the trim at the corner so it can fold round without bunching.
What temperatures can it take?
The trim is rated for −10 °C to +60 °C, so it suits outdoor equipment in the UK climate. Avoid fitting it next to hot exhausts, ovens or other heat sources above 60 °C.
Can it be used outdoors or around water?
Yes. The PVC jacket covers the steel carrier on every face except the cut ends, and PVC resists weathering and moisture. On boats or in very wet places, seal the cut ends if you are concerned about the carrier rusting.
Is it the same as the 10.5 × 14.5 mm trim?
No. It is a different profile. Check the drawing and the panel range above before you order.
When will it arrive?
All lengths are held in stock in the UK and dispatched the same working day, as shown in the dispatch message on this page.
If you need help choosing a profile, call +44 1282 277786 or email sales@industrial-polymers.co.uk.
Product details
| SKU | IP-SGET-10.5X14.3-40 |
|---|---|
| Weight | 6.17 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Self-Grip PVC Edge Trim – 10.5mm x 14.3mm – Fits 1.5mm to 3mm Panels – 40m to 50m