
Rubber & FoamSKU IP-SGET-12X15.5-12M
PVC Self-Grip Edge Trim – 12mm x 15.5mm for 8mm to 9.5mm Panels – 12m to 50m Lengths
Price shown updates with the option you pick.
This PVC self-grip edge trim 12mm x 15.5mm pushes over 8mm to 9.5mm thick panel edges and grips by itself, thanks to a steel carrier and internal gripping fingers, so sharp or rough edges are covered and protected without glue. It is sold as one continuous length, from 12m up to a full 50m coil.
At a glance
- Profile: 12mm wide x 15.5mm high U-shaped edge protector
- Fits 8mm to 9.5mm panel, sheet and board edges
- Black PVC with a steel carrier running the full length, so it holds its shape under pressure
- Internal gripping fingers: push-on fitting, no adhesive, removable and reusable
- Resists weather, moisture and many chemicals; -10°C to +60°C
- Bends around radii and curved edges
- One continuous length per order: 12m to 49m, or a full 50m coil
Typical uses
- Covering sharp sheet metal and fibreglass edges on guards, panels and enclosures
- Finishing the edges of computer and electrical cabinets
- Garage doors, sheds and outdoor equipment edges
- Playground and leisure equipment where exposed edges must be made safe
- Marine equipment and interior side panels or side windows
- Protecting board edges in storage and transport
Which one do I need?
| Panel edge thickness | Best choice |
|---|---|
| 8mm to 9.5mm | This PVC self-grip edge trim 12mm x 15.5mm |
| 1mm to 4mm, food or high-heat area | Silicone self-grip edge trim 8.9mm x 12.4mm |
| Thin sheet edges, compact trim | PVC self-grip edge trim 6.5mm x 9.5mm |
| Very thin sheet edges, smallest trim | PVC self-grip edge trim 5.5mm x 8.5mm |
Technical drawing
Specification
| Product | Self-grip edge trim with steel carrier |
| Material | PVC with steel carrier |
| Profile size | 12mm wide x 15.5mm high |
| To fit panel | 8mm to 9.5mm |
| Wall thickness | 2.5mm |
| Hardness | 70 Shore A (range 67-82) |
| Tensile strength | Over 11 MPa |
| Elongation at break | Over 260% |
| Density | 1.35-1.45 g/cm³ |
| Temperature range | -10°C to +60°C |
| Colour | Black |
| Unit of sale | One continuous length per order, 12m to 49m, or a full 50m coil |
How much do I need?
Add up every edge you want to cover and allow about 5% for trimming. Example: four 2.4m x 1.2m guard panels edged on all sides need 4 x 7.2m = 28.8m, plus 5% = 30.2m, so order 31m. A single panel of that size needs about 7.6m, so the 12m minimum covers it. If you need more than about 42m, the full 50m coil is priced lower than the longest cut lengths, so it is the better buy.
Fitting tips
- Check your edge thickness first: the trim grips properly on 8mm to 9.5mm material.
- Clean and de-burr the edge, then press the trim on by hand, starting at one end.
- Seat it fully with a rubber or plastic mallet; never use a steel hammer on the PVC face.
- Bend gently around curves; on tight internal corners cut a small V-notch in the legs so the steel carrier does not kink.
- Cut to length with heavy-duty side cutters or a fine hacksaw, as the carrier is steel.
Complete your project
- Self-Grip PVC Edge Trim – 6.5mm x 9.5mm – 50m Coil
- Silicone Self-Grip Edge Trim – 8.9mm x 12.4mm – 1mm to 4mm Panels
- EPDM Self-Grip Door Seal – 15.5mm x 10mm
Questions
What panel thickness does this edge trim fit?
It is made for edges 8mm to 9.5mm thick. Thinner panels need one of the smaller self-grip edge protectors listed above.
Do I need glue to fit this edge protector?
No. The steel carrier and internal gripping fingers hold it on the edge, so it pushes on by hand and can be removed and reused.
Can this PVC edge trim be used outdoors?
Yes. PVC resists weather and moisture, so it suits sheds, garage doors and outdoor equipment within its -10°C to +60°C range.
Will it go round curves?
Yes, the trim bends around radii and curved edges. On tight internal corners, notch the legs so it lies flat without kinking the carrier.
How long is each piece?
You choose the length, from 12m to 49m, and it is supplied as one continuous piece. The 50m option is a full coil.
Need help choosing an edge trim? Contact our team with your edge thickness and we will recommend the right profile.
Product details
| SKU | IP-SGET-12X15.5-12M |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:PVC Self-Grip Edge Trim – 12mm x 15.5mm for 8mm to 9.5mm Panels – 12m to 50m Lengths