
Rubber & FoamSKU IP-CDP-74X18-BLK
Rubber Cable Protector – Single Channel 74mm x 18mm – 9m Roll
This rubber cable protector 74mm x 18mm covers a single trailing lead across office, classroom and shop floors, turning a trip hazard into a low, sloped ramp that people and light trolleys cross easily. It is sold as one continuous 9m roll that you cut to the lengths you need.
At a glance
- 74mm wide x 18mm high low-profile cord cover with sloped sides
- Single 19mm x 6mm channel for one power lead, data or extension cable
- Pre-split base so cables drop in from underneath without threading
- Ribbed underside grips carpet, vinyl, timber and sealed concrete
- 85° Shore A black elastomer, -15°C to +55°C working range
- Supplied as a 9m roll; cuts cleanly with a sharp utility knife
Typical uses
- Leads running to desks, hot-desk islands and workstations
- Projector and AV cables across meeting rooms and lecture halls
- Temporary power to tills, displays and promotional stands in retail units
- Cable runs along corridors and reception areas during fit-outs
Which one do I need?
| Cable cover | Channel | Best for |
|---|---|---|
| 63.5mm x 15mm cord protector | Single, smaller | Thin leads where the lowest possible ramp matters |
| 74mm x 18mm (this cable protector) | Single 19mm x 6mm | Standard flat or round power and data leads in offices and schools |
| 68mm x 15mm hazard warning | Single | Where a high-visibility yellow and black cover is needed |
| 127mm x 28mm industrial | 23mm round hole | Thicker cables, workshops and heavier traffic |
Technical drawing
Specification
| Product | Single channel rubber cable protector (cord cover) |
| Material | Black elastomer |
| Overall width | 74mm |
| Overall height | 18mm |
| Channel size | 19mm wide x 6mm high |
| Base | Pre-split, ribbed underside |
| Hardness | 85° Shore A |
| Tensile strength | 15.1 MPa |
| Elongation at break | 258% |
| Working temperature | -15°C to +55°C |
| Unit of sale | One 9m roll |
How much do I need?
Measure each crossing point from wall or desk leg to where the cable leaves the walkway and add about 100mm at each end so the cover runs past the edge of the traffic route. For example, three desk crossings of 1.8m, 2.2m and 2.6m need 6.6m plus 0.6m of overrun, so 7.2m in total: one 9m roll covers it with a spare length left over.
Fitting tips
- Unroll the protector and let it lie flat at room temperature for a few hours so it loses its coil set.
- Clean and dry the floor first; dust stops the ribbed base from gripping.
- Open the split in the base, press the lead up into the 19mm x 6mm channel and let the base close around it.
- Cut square ends with a sharp knife against a straight edge so the ends sit flat and do not catch toes.
Complete your project
- Elastomer Cord Protector – 63.5mm x 15mm Single Channel – 9m Roll
- Hazard Warning Cable Protector – 68mm x 15mm – Per Length
- Rubber Cable Protector – 127mm x 28mm, 23mm Hole – 4.5m or 9m Length
Questions
Can I cut the 9m roll into shorter cable covers?
Yes. Use a sharp utility knife and a straight edge; each piece works as a separate floor cord cover.
What size of cable fits the channel?
The channel is 19mm wide and 6mm high, which suits one flat or slim round power lead, a network cable or a light extension lead. For thicker cables choose the 127mm x 28mm cable protector with its 23mm hole.
Does the cable protector need tape or adhesive?
Usually not. The ribbed rubber base grips most indoor floors. On very smooth or polished floors you can add double-sided carpet tape under the edges.
Can wheeled equipment cross it?
Yes, the sloped sides let office chairs, sack trucks and light trolleys roll over. It is for indoor use and not intended for vehicles.
Need help choosing? Contact our team and we will point you to the right cable cover.
Product details
| SKU | IP-CDP-74X18-BLK |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Rubber Cable Protector – Single Channel 74mm x 18mm – 9m Roll