Rubber & FoamSKU IP-SLLP-10X5-BLACK
Silicone L Profile – 10mm x 5mm, Light Section (3.6mm Upright, 2mm Base) – 25m Coil
A solid silicone angle section, 10mm wide and 5mm high, with a slim 3.6mm upright and a 2mm base. This is the lighter of our two 10 x 5mm L profiles: it leaves a deep 6.4 x 3mm step that seats over a sheet or panel corner, so it caps and cushions an edge without adding much bulk. Made from 60 Shore A silicone, it stays flexible from -50°C to +180°C and the compound meets FDA 21 CFR 177.2600, EC 1935/2004 and WRAS. Sold as one continuous 25m coil in seven colours.
At a glance
- Size: 10mm wide x 5mm high, light section (3.6mm upright, 2mm base)
- Step: 6.4mm wide x 3mm deep, the pocket that sits over an edge
- Material: solid silicone, 60 Shore A
- Temperature: -50°C to +180°C working range
- Compliance: FDA 21 CFR 177.2600, EC 1935/2004, WRAS approved
- Supplied as: one 25m coil, £27.00 per metre inc VAT
- Colours: black, blue, green, red, translucent, white, yellow
Which 10 x 5mm L profile do you need?
We stock two silicone L profiles with the same 10 x 5mm outside size. Their wall thicknesses are different. Measure the edge you are covering and pick the step that suits it.
| This profile: light section | Heavy section | |
|---|---|---|
| Overall size | 10 x 5mm | 10 x 5mm |
| Upright width | 3.6mm | 5mm |
| Base thickness | 2mm | 2.5mm |
| Step (width x depth) | 6.4 x 3mm | 5 x 2.5mm |
| Cross-section area (calculated) | 30.8mm² | 37.5mm² |
| Best for | Lighter, more flexible cap with a deeper pocket; follows curves more easily | Stiffer, more impact-absorbing bumper |
Technical drawing
![]()
Specifications
| Property | Value | Test method / note |
|---|---|---|
| Profile type | Solid L (angle) section | - |
| Overall width | 10.0mm | Supplier drawing |
| Overall height | 5.0mm | Supplier drawing |
| Upright (vertical leg) width | 3.6mm | Supplier drawing |
| Base (horizontal leg) thickness | 2.0mm | Supplier drawing |
| Step width x depth | 6.4 x 3.0mm | Derived from the drawing (10 - 3.6, 5 - 2) |
| Wall thickness range | 2.0 to 3.6mm | Supplier data |
| Dimensional tolerance | Class E2 | ISO 3302-1:2014 |
| Coil length | 25m continuous | - |
| Approximate weight | 35g per metre, about 0.9kg per coil | Calculated from section area x density |
| Material | Silicone rubber (VMQ), solid | - |
| Hardness | 60 Shore A | DIN ISO 48-4 |
| Density | 1.15 g/cm³ | DIN EN ISO 1183-1 method A |
| Tensile strength | 11 N/mm² (11 MPa) | ISO 37 type 1 |
| Elongation at break | 550% | ISO 37 type 1 |
| Tear strength | 26 N/mm | ASTM D624 die B |
| Compression set | 31% after 22h at 175°C | DIN ISO 815-1 type B, method A |
| Rebound resilience | 59% | ISO 4662 |
| Working temperature | -50°C to +180°C | - |
| Environmental resistance | Ozone, UV, oxidation, weathering, cosmic and ionising radiation, corona discharge | - |
| Colours | Black, blue, green, red, translucent, white, yellow | - |
Materials and compliance
The manufacturer's datasheet for this exact profile states that the silicone compound is:
- compliant with FDA 21 CFR 177.2600 (rubber articles for repeated food contact)
- compliant with EC 1935/2004 (materials in contact with food)
- WRAS approved for use with drinking water
- free from TSE/BSE animal by-products
- free from phthalates
Food and water approvals cover the material. Check that your finished assembly suits its own food-safety or water-regulations requirements.
Typical uses
- Capping and cushioning sheet-metal and panel corners on machine guards, enclosures and conveyor side guards
- Edge protection for glass, acrylic and composite panels
- Food, bakery and beverage equipment where an FDA or EC 1935/2004 material is needed
- Drinking-water equipment covers and housings (WRAS-approved compound)
- Oven, dryer and hot-cabinet panel edges, up to +180°C
- Colour-coded edges for zone marking in food plants and cleanrooms
Fitting
- Clean the edge and dry it. Remove grease with isopropyl alcohol.
- Seat the panel corner into the 6.4 x 3mm step so the 2mm base lies along one face and the 3.6mm upright covers the other.
- For a permanent or watertight fit, run a thin bead of silicone adhesive-sealant along the inside of the step before pressing it home. Most adhesives do not bond to silicone.
- Cut lengths about 1% long and push them together, so the ends stay closed as the profile relaxes.
- At corners, mitre the profile at 45° with a sharp blade and seal the joint with silicone sealant. Alternatively, cut a V-notch out of the upright and bend the base round.
Frequently asked questions
What size edge does it fit?
The step is 6.4mm wide and 3mm deep. It caps the corner of a sheet or panel, covering up to 6.4mm of one face and up to 3mm of the other. It is a solid angle, not a push-on U channel, so it is bonded or held in place rather than gripping the edge.
How is this different from your other 10 x 5mm silicone L profile?
Both measure 10 x 5mm overall. This light section has a 3.6mm upright and a 2mm base. The heavy section has a 5mm upright and a 2.5mm base. It is stiffer and absorbs more impact, but its step is smaller (5 x 2.5mm).
Can it be used in food production?
Yes. The manufacturer states the compound meets FDA 21 CFR 177.2600 and EC 1935/2004. The colours also suit colour-coded hygiene zones.
What temperatures can it take?
The working range is -50°C to +180°C. At 175°C for 22 hours it takes a compression set of 31%, so it keeps its shape well on hot equipment.
How do I cut and join it?
Cut it with a sharp knife or a rubber cutter against a straight edge. Make butt joints and mitres with a silicone sealant or a silicone-compatible instant adhesive with primer. Ordinary contact adhesives will not hold silicone.
Is it suitable outdoors?
Yes. The datasheet lists resistance to ozone, UV, oxidation and weathering, so it will not crack or chalk outdoors as many black rubbers do.
Can I buy it by the metre?
This profile comes as a full 25m coil, which works out at £27.00 per metre inc VAT. Contact us if you need a shorter length or a different colour.
When will it arrive?
It is held in stock. See the dispatch message above the add-to-basket button.
Data sheet
Download the technical data sheet (PDF)
Related profiles
- Silicone L Profile 10 x 5mm, heavy section (5mm upright, 2.5mm base)
- Silicone L Profile 7.7 x 7.1mm, 25m coil
- Silicone L Profile 10 x 10mm, 25m coil
Need help choosing? Call +44 1282 277786 or email sales@industrial-polymers.co.uk.
Product details
| SKU | IP-SLLP-10X5-BLACK |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone L Profile – 10mm x 5mm, Light Section (3.6mm Upright, 2mm Base) – 25m Coil