Rubber & FoamSKU IP-SILP-7.7X7.1-BLACK
Silicone L Profile – 7.7mm x 7.1mm – 25m Coil
A heavy, solid silicone L profile measuring 7.7mm wide x 7.1mm high. The upright is a thick 5.2mm and the base is 3.0mm, so it works as a tough corner bumper and seal for exposed edges on food, water, HVAC and general engineering equipment. It is made from 70 Shore A silicone: firm enough to hold its square shape and absorb knocks, yet flexible enough to follow gentle curves. It comes as a continuous 25m coil in seven colours, all held in stock for same-day dispatch.
At a glance
- Size: 7.7mm wide x 7.1mm high, solid L section
- Walls: 5.2mm upright, 3.0mm base. The inside step is 2.5mm x 4.1mm.
- Material: silicone rubber, 70 Shore A, rated -50°C to +180°C
- Compliance: FDA 21 CFR 177.2600, EC 1935/2004 and WRAS approved material
- Colours: black, blue, green, red, translucent, white and yellow
- Supplied as: one 25m coil, £675.00 inc VAT (£27.00 per metre)
Technical drawing
![]()
Nominal dimensions in mm. Tolerances are to ISO 3302-1:2014 class E2 for extruded solid rubber sections.
Specification
| Property | Value | Test method |
|---|---|---|
| Profile type | Solid L (angle) section | – |
| Overall width | 7.7 mm | Nominal, ISO 3302-1 E2 |
| Overall height | 7.1 mm | Nominal, ISO 3302-1 E2 |
| Upright (leg) thickness | 5.2 mm | Nominal, ISO 3302-1 E2 |
| Base thickness | 3.0 mm | Nominal, ISO 3302-1 E2 |
| Wall thickness range | 3.0 mm to 5.2 mm | Nominal |
| Inside step (derived) | 2.5 mm wide x 4.1 mm deep | Calculated from the dimensions above |
| Coil length | 25 m continuous | – |
| Material | Silicone rubber | – |
| Hardness | 70 Shore A | DIN ISO 48-4 |
| Density | 1.18 g/cm³ | DIN EN ISO 1183-1 method A |
| Tensile strength | 11.3 N/mm² (11.3 MPa) | ISO 37 type 1 |
| Elongation at break | 530 % | ISO 37 type 1 |
| Tear strength | 31 N/mm | ASTM D624 die B |
| Compression set, 22 h at 175°C | 40 % | DIN ISO 815-1 type B, method A |
| Rebound resilience | 55 % | ISO 4662 |
| Operating temperature | -50°C to +180°C | – |
| Environmental resistance | Ozone, UV, oxidation, weathering, cosmic and ionising radiation, corona discharge | – |
| Dimensional tolerance | ISO 3302-1 class E2 | ISO 3302-1:2014 |
| Colours | Black, blue, green, red, translucent, white, yellow | – |
| SKU | IP-SILP-7.7X7.1-[COLOUR] | – |
All values are for this profile's silicone compound.
Download the technical data sheet (PDF)
Materials and compliance
- FDA 21 CFR 177.2600: the compound complies with the US rule for rubber articles in repeated food contact.
- EC 1935/2004: the compound complies with the EU framework regulation for food-contact materials.
- WRAS approved material: suitable for potable water and public water supply applications.
- Free from TSE/BSE-derived products and free from phthalates.
Food-contact and water approvals cover the material. Check that your finished assembly meets your own process requirements.
Typical uses
- Bumper and seal for outside corners on machine guards, enclosures and HVAC units
- Impact and abrasion protection for glass, sheet metal and panel edges
- Corner seals on doors, windows, hatches and frames, keeping out water, air and dust
- Food and beverage processing equipment
- Potable water and public water supply equipment
- Cleanrooms and laboratories, where a smooth, wipe-clean edge is needed
- Classic cars, caravans, motorhomes and rail vehicles
- Colour coding: use red, blue, green or yellow to mark hygiene zones or hazard edges
How it fits
![]()
The inside step of the L sits on the corner. It covers 2.5mm of one face and 4.1mm of the other, with 3.0mm of silicone over the first face and a thick 5.2mm over the second.
- Clean and degrease the edge first.
- For many edge-protection jobs it can simply be laid in place without adhesive. For a permanent or watertight joint, bed it in a compatible silicone or polyurethane adhesive sealant.
- Lay it in relaxed, without stretching. Cut slightly long, then trim.
- Cut with a sharp knife or shears. Mitre at 45° for neat closed corners.
Which one do I need?
| Need | Suggested profile |
|---|---|
| Heavy corner bumper with a 5.2mm thick upright | This 7.7mm x 7.1mm silicone L profile, 70 Shore A |
| Slightly smaller, with even 3mm walls | Silicone L profile 6.2mm x 5.2mm |
| Similar width, lower height | Silicone L profile 7.5mm x 5.5mm |
| Small, hard angle | Silicone L profile 5mm x 6mm, 80 Shore A |
| Wider leg to cover more of the face | Silicone L profile 10mm x 7mm |
| Larger section with 10mm legs | Silicone L profile 10mm x 10mm, heavy 5mm wall |
How much do I need?
Measure every edge you want to cover and add about 5% for cuts and mitres. For example, edging four inspection doors of 400mm x 600mm needs 4 x 2.0m = 8m, plus 5% = 8.4m. One 25m coil covers that job almost three times. At £27.00 per metre, a full coil is the most economical way to buy.
Frequently asked questions
How does it fit onto an edge?
Seat the inside step of the L over an outside corner. It wraps 2.5mm onto one face and 4.1mm onto the other. For light-duty edge protection it can be laid in place without adhesive; for a permanent or watertight fit, bond it with silicone or polyurethane sealant.
What size edge or corner does it suit?
It suits any 90° outside corner. The step covers 2.5mm x 4.1mm, and overall the profile adds 7.7mm x 7.1mm to the corner, with 5.2mm of silicone on one face and 3.0mm on the other for strong impact protection.
Is it food safe?
Yes. The compound meets FDA 21 CFR 177.2600 and EC 1935/2004 for food-contact use, and it is free from phthalates and TSE/BSE-derived products.
Can it be used near drinking water?
Yes. The material is WRAS approved for potable water applications.
What temperatures can it take?
It works continuously from -50°C to +180°C. It also resists UV, ozone and weathering, so it is suitable outdoors.
How hard is it, and will it spring back?
It is 70 Shore A: firm enough to stay square on a corner, but still flexible. Its compression set is 40% after 22 hours at 175°C, so it recovers well when pressed, which helps it keep sealing over time.
How do I cut and join it?
Cut it with a sharp knife or shears on a cutting board. Mitre corners at 45° and bond the joint with a silicone adhesive sealant. Do not join it with standard cyanoacrylate glues: silicone does not bond well without a silicone primer.
Is it in stock, and how is it supplied?
Yes. All seven colours are held in stock as continuous 25m coils, priced per coil.
Need help choosing a silicone L profile? Contact our team on +44 1282 277786 or sales@industrial-polymers.co.uk.
Product details
| SKU | IP-SILP-7.7X7.1-BLACK |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone L Profile – 7.7mm x 7.1mm – 25m Coil